P0443 Evaporative Emission Control System Purge Control Valve Circuit
Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
DESCRIPTION
To reduce HC emissions, evaporated fuel from the fuel tank is routed through a charcoal canister to the intake manifold for combustion in the cylinders.The ECM changes the duty signals to the purge VSV so that the intake amount of HC emissions is appropriate for driving conditions (engine load, engine speed, vehicle speed, etc.) after the engine is warmed up.
| DTC Code |
DTC Detection Condition |
Trouble Area |
| P0443 |
The terminal voltage of the ECM output circuit does not correspond with the drive signals from the ECM to the purge VSV (1 trip detection logic). |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air fuel ratio was lean or rich, and other data from the time the malfunction occurred.
| 1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (ACTIVATE THE VSV FOR EVAP CONTROL) |
Connect the intelligent tester to the DLC3.

Remove the vacuum hose of the purge VSV from the charcoal canister.
Start the engine and turn the tester on.
Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Evap Control.
When the purge VSV is operated using the intelligent tester, check whether the disconnected hose applies suction to your finger.
- OK:
Tester Operation
Specified Condition
VSV is ON
Disconnected hose applies suction to finger
VSV is OFF
Disconnected hose applies no suction to finger
|
|
||||
| NG | |
| 2. INSPECT PURGE VSV |
Inspect the purge VSV (Click here).
|
|
||||
| OK | |
| 3. INSPECT PURGE VSV (POWER SOURCE VOLTAGE) |
![]() ![]() |
Disconnect the purge VSV connector.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
C19-1 - Body ground
Ignition switch ON
11 to 14 V
|
|
||||
| NG | |
| 4. CHECK HARNESS AND CONNECTOR (PURGE VSV - EFI NO. 2 FUSE) |
![]() ![]() |
Remove the EFI NO. 2 fuse from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance (Check for Open):
Tester Connection
Condition
Specified Condition
C19-1 - EFI NO. 2 fuse (2)
Always
Below 1 Ω
- Standard Resistance (Check for Short):
Tester Connection
Condition
Specified Condition
C19-1 or EFI NO. 2 fuse (2) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||
| 5. CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM) |
![]() ![]() |
Disconnect the purge VSV connector.
Disconnect the ECM connector.
Measure the resistance between the terminals of the wire harness side connectors.
- Standard Resistance (Check for Open):
for LHD Tester Connection
Condition
Specified Condition
C19-2 - PRG (C45-108)
Always
Below 1 Ω
for RHD Tester Connection
Condition
Specified Condition
C19-2 - PRG (C46-108)
Always
Below 1 Ω
- Standard Resistance (Check for Short):
for LHD Tester Connection
Condition
Specified Condition
C19-2 or PRG (C45-108) - Body ground
Always
10 kΩ or higher
for RHD Tester Connection
Condition
Specified Condition
C19-2 or PRG (C46-108) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||



