P0340 Camshaft Position Sensor Circuit Malfunction
Diagnostic trouble codes · Vehicles built from Jan 2012
Also covers:
- P0342 Camshaft Position Sensor "A" Circuit Low Input (Bank 1 or Single Sensor)
- P0343 Camshaft Position Sensor "A" Circuit High Input (Bank 1 or Single Sensor)
- P0345 Camshaft Position Sensor "A" Circuit (Bank 2)
- P0347 Camshaft Position Sensor "A" Circuit Low Input (Bank 2)
- P0348 Camshaft Position Sensor "A" Circuit High Input (Bank 2)
DESCRIPTION
The intake camshaft VVT sensor (VV1 and VV2 signal) consists of a magnet and MRE (Magnetoresistive Element).The intake camshaft has 3 teeth on its outer circumference. When the intake camshaft rotates, changes occur in the air gaps between the 3 teeth and MRE, which affects the magnetic field. As a result, the resistance of the MRE fluctuates. The VVT sensor converts the camshaft rotation data into pulse signals, uses the pulse signals to determine the camshaft angle, and sends the data to the ECM.
The crankshaft angle sensor rotor has 34 teeth. The MRE generates 34 signals for each crankshaft revolution. Based on a combination of the VVT signal and NE signal, the ECM detects the crankshaft angle. Then the ECM uses this data to control fuel injection time and injection timing. Also, based on the NE signal, the ECM detects the engine speed.
| DTC No. |
DTC Detection Condition |
Trouble Area |
| P0340 P0345 |
No VVT sensor signal is sent to the ECM at an engine speed of 600 rpm or more (1 trip detection logic). |
|
| P0342 P0347 |
Output voltage of VVT sensor is below 0.3 V for 4 seconds (1 trip detection logic). |
|
| P0343 P0348 |
Output voltage of VVT sensor is higher than 4.7 V for 4 seconds (1 trip detection logic). |
|
-
Reference: Inspection using an oscilloscope

- Standard:
for RHD Tester Connection
Tool Setting
Condition
Specified Condition
C46-110 (NE+) - C46-111 (NE-)
5 V/DIV.
20 msec./DIV.
Cranking or idling
The correct waveform is as shown
C46-92 (VV1+) - C46-91 (VV1-)
5 V/DIV.
20 msec./DIV.
Cranking or idling
The correct waveform is as shown
C46-87 (VV2+) - C46-88 (VV2-)
5 V/DIV.
20 msec./DIV.
Cranking or idling
The correct waveform is as shown
for LHD Tester Connection
Tool Setting
Condition
Specified Condition
C45-110 (NE+) - C45-111 (NE-)
5 V/DIV.
20 msec./DIV.
Cranking or idling
The correct waveform is as shown
C45-92 (VV1+) - C45-91 (VV1-)
5 V/DIV.
20 msec./DIV.
Cranking or idling
The correct waveform is as shown
C45-87 (VV2+) - C45-88 (VV2-)
5 V/DIV.
20 msec./DIV.
Cranking or idling
The correct waveform is as shown
- HINT:
- VV1 and VV2 are the VVT sensor signals, and NE is the crankshaft position sensor signal.
MONITOR DESCRIPTION
If no signal is transmitted by the VVT sensor despite the engine running, or the rotations of the camshaft and crankshaft are not synchronized, the ECM interprets this as a malfunction of the sensor.Also, when the sensor output voltage remains at below 0.3 V, or higher than 4.7 V for more than 4 seconds, the ECM stores a DTC.
CONFIRMATION DRIVING PATTERN
- Start the engine and run it at idle for 10 seconds or more.
WIRING DIAGRAM


INSPECTION PROCEDURE
- HINT:
- Read freeze frame data using the GTS. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
- Bank 1 refers to the bank that includes the No. 1 cylinder*.
*: The No. 1 cylinder is the cylinder which is farthest from the transmission.
- Bank 2 refers to the bank that does not include the No. 1 cylinder.
- Read freeze frame data using the GTS. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.
| 1. CHECK HARNESS AND CONNECTOR (SENSOR POWER SOURCE) |
![]() ![]() |
Disconnect the VVT sensor connector.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
3 (VC) - Body ground
Engine switch on (IG)
4.5 to 5.0 V
Text in Illustration *A
Bank 1
*B
Bank 2
*a
Front view of wire harness connector
(to VVT Sensor)
|
|
||||
| OK | |
| 2. CHECK HARNESS AND CONNECTOR (VVT SENSOR FOR INTAKE CAMSHAFT - ECM) |
Disconnect the VVT sensor connector.
Disconnect the ECM connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
for RHD Tester Connection
Condition
Specified Condition
C100-1 (VVL+) - C46-92 (VV1+)
Always
Below 1 Ω
C100-2 (VVL-) - C46-91 (VV1-)
Always
Below 1 Ω
C101-1 (VVR+) - C46-87 (VV2+)
Always
Below 1 Ω
C101-2 (VVR-) - C46-88 (VV2-)
Always
Below 1 Ω
C100-1 (VVL+) or C46-92 (VV1+) - Body ground
Always
10 kΩ or higher
C100-2 (VVL-) or C46-91 (VV1-) - Body ground
Always
10 kΩ or higher
C101-1 (VVR+) or C46-87 (VV2+) - Body ground
Always
10 kΩ or higher
C101-2 (VVR-) or C46-88 (VV2-) - Body ground
Always
10 kΩ or higher
for LHD Tester Connection
Condition
Specified Condition
C100-1 (VVL+) - C45-92 (VV1+)
Always
Below 1 Ω
C100-2 (VVL-) - C45-91 (VV1-)
Always
Below 1 Ω
C101-1 (VVR+) - C45-87 (VV2+)
Always
Below 1 Ω
C101-2 (VVR-) - C45-88 (VV2-)
Always
Below 1 Ω
C100-1 (VVL+) or C45-92 (VV1+) - Body ground
Always
10 kΩ or higher
C100-2 (VVL-) or C45-91 (VV1-) - Body ground
Always
10 kΩ or higher
C101-1 (VVR+) or C45-87 (VV2+) - Body ground
Always
10 kΩ or higher
C101-2 (VVR-) or C45-88 (VV2-) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 3. CHECK SENSOR INSTALLATION (VVT SENSOR FOR INTAKE CAMSHAFT) |
Check the VVT sensor installation.

- OK:
- Sensor is installed correctly.
|
|
||||
| OK | |
| 4. INSPECT INTAKE CAMSHAFT (TEETH) |
Check the teeth of the camshaft.
- OK:
- Teeth do not have any cracks or deformation.
|
|
||||
| OK | |
| 5. REPLACE VVT SENSOR |
Replace the VVT sensor (Click here).
| NEXT | |
| 6. CHECK WHETHER DTC OUTPUT RECURS |
Connect the GTS to the DLC3.
Turn the engine switch on (IG).
Turn the GTS on.
Clear DTCs.
Start the engine and idle it for 10 seconds or more.
Enter the following menus: Powertrain / Engine and ECT / Trouble Codes / Pending.
Read DTCs.
Result Result
Proceed to
No DTC is output
A
P0340, P0342, P0343, P0345, P0347 or P0348 is output
B
- HINT:
- If the engine does not start, replace the ECM.
|
|
||||
| A | ||
| ||

