Rear Power Window RH does not Operate with Rear Power Window Switch RH
Circuit diagnosis · Vehicles built Sep 2011 – Dec 2011
Versions by build date: Sep 2011 – Dec 2011from Jan 2012
DESCRIPTION
If the manual up/down function does not operate, there may be a malfunction in the rear power window regulator switch, rear power window regulator motor RH, multiplex network master switch assembly, harness or connector.
WIRING DIAGRAM
INSPECTION PROCEDURE
1. INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH
Remove the rear power window regulator switch assembly RH (Click here).
Measure the resistance according to the value(s) in the table below.
Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
4 (U) - 3 (B)
UP
Below 1 Ω
2 (SD) - 1 (D)
5 (SU) - 4 (U)
OFF
Below 1 Ω
2 (SD) - 1 (D)
5 (SU) - 4 (U)
DOWN
Below 1 Ω
3 (B) - 1 (D)
NG
REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY RH (Click here)
OK
2. INSPECT REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH
Remove the rear power window regulator motor assembly RH (Click here).
Apply battery voltage to the regulator motor and check the operation of the regulator motor.
Text in Illustration
*1
Motor Gear
*a
Clockwise
*b
Counterclockwise
OK:
Measurement Condition
Specified Condition
Battery positive (+) → 1 Battery negative (-) → 2
Motor gear rotates clockwise
Battery positive (+) → 2 Battery negative (-) → 1
Motor gear rotates counterclockwise
NG
REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY RH (Click here)
OK
3. CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH RH - BATTERY)
Disconnect the J21 rear power window regulator switch assembly RH connector.
Measure the voltage according to the value(s) in the table below.
Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
J21-3 (B) - Body ground
Ignition switch ON
11 to 14 V
Text in Illustration
*a
Front view of wire harness connector (to Rear Power Window Regulator Switch Assembly RH)
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
4. CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH RH - REAR POWER WINDOW REGULATOR MOTOR RH)
Disconnect the J21 rear power window regulator switch assembly RH connector.
Disconnect the J20 rear power window regulator motor assembly RH connector.
Measure the resistance according to the value(s) in the table below.
Standard Resistance:
for LHD
Tester Connection
Condition
Specified Condition
J21-4 (U) - J20-1
Always
Below 1 Ω
J21-1 (D) - J20-2
Always
Below 1 Ω
J21-4 (U) or J20-1 - Body ground
Always
10 KΩ or higher
J21-1 (D) or J20-2 - Body ground
Always
10 KΩ or higher
NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK
5. CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH RH - REAR POWER WINDOW REGULATOR MOTOR RH)
Disconnect the J21 rear power window regulator switch assembly RH connector.
Disconnect the I31*1 or I26*2 multiplex network master switch assembly connector.
*1: for LHD
*2: for RHD
Measure the resistance according to the value(s) in the table below.