2011-2013 Land Cruiser · Service Manual Vehicle Exterior

Rear Power Window LH does not Operate with Rear Power Window Switch LH

Circuit diagnosis · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

  1. If the manual up/down function does not operate, there may be a malfunction in the rear power window regulator switch, power window rear regulator motor LH, multiplex network master switch assembly, harness or connector.

WIRING DIAGRAM

B292714E02

INSPECTION PROCEDURE


1. INSPECT REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH

  1. B107881E07
    Remove the rear power window regulator switch assembly LH (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    4 (U) - 3 (B)
    UP
    Below 1 Ω
    2 (SD) - 1 (D)
    5 (SU) - 4 (U)
    OFF
    Below 1 Ω
    2 (SD) - 1 (D)
    5 (SU) - 4 (U)
    DOWN
    Below 1 Ω
    3 (B) - 1 (D)



NG
REPLACE REAR POWER WINDOW REGULATOR SWITCH ASSEMBLY LH (Click here)
OK


2. INSPECT REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH

  1. B171738E15
    Remove the rear window regulator motor assembly LH (Click here).

  1. Apply battery voltage to the motor connector according to the table below.

    Text in Illustration 
    *1
    Motor Gear
    *a
    Counterclockwise
    *b
    Clockwise

    OK:
    Measurement Condition
    Specified Condition
    Battery positive (+) → 1
    Battery negative (-) → 2
    Motor gear rotates clockwise
    Battery positive (+) → 2
    Battery negative (-) → 1
    Motor gear rotates counterclockwise



NG
REPLACE REAR POWER WINDOW REGULATOR MOTOR ASSEMBLY LH (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH LH - BATTERY)

  1. B291669E06
    Disconnect the J23 rear power window regulator switch assembly LH connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    J23-3 (B) - Body ground
    Ignition switch ON
    11 to 14 V

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Rear Power Window Regulator Switch Assembly LH)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH LH - REAR POWER WINDOW REGULATOR MOTOR LH)
  1. Disconnect the J23 rear power window regulator switch assembly LH connector.

  1. Disconnect the J22 rear power window regulator motor assembly LH connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    J23-4 (U) - J22-1
    Always
    Below 1 Ω
    J23-1 (D) - J22-2
    Always
    Below 1 Ω
    J23-4 (U) or J22-1 - Body ground
    Always
    10 KΩ or higher
    J23-1 (D) or J22-2 - Body ground
    Always
    10 KΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK HARNESS AND CONNECTOR (REAR POWER WINDOW REGULATOR SWITCH LH - MULTIPLEX NETWORK MASTER SWITCH)
  1. Disconnect the J23 rear power window regulator switch assembly LH connector.

  1. Disconnect the I31*1 or I26*2 multiplex network master switch assembly connector.

    1. *1: for LHD
    2. *2: for RHD

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    J23-5 (SU) - I31-12 (U)
    Always
    Below 1 Ω
    J23-2 (SD) - I31-13 (D)
    Always
    Below 1 Ω
    J23-5 (SU) or I30-12 (U) - Body ground
    Always
    10 kΩ or higher
    J23-2 (SD) or I30-13 (D) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    J23-5 (SU) - I26-18 (U)
    Always
    Below 1 Ω
    J23-2 (SD) - I26-10 (D)
    Always
    Below 1 Ω
    J23-5 (SU) or I26-18 (U) - Body ground
    Always
    10 kΩ or higher
    J23-2 (SD) or I26-10 (D) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MULTIPLEX NETWORK MASTER SWITCH ASSEMBLY (Click here)


← Rear Power Window LH does not Operate with Rear Power Window Switch LH (Sep 2011 – Dec 2011)Rear Power Window RH does not Operate with Rear Power Window Switch RH (Sep 2011 – Dec 2011) →