2011-2013 Land Cruiser · Service Manual Vehicle Interior

One or more Power Seat Motors do not Operate

Circuit diagnosis · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

When the front power seat switch is operated, a command signal is sent to the position control ECU. The position control ECU then controls the appropriate seat motor as needed. The position control ECU is designed so that a malfunction of the seat memory system will not interfere with manual seat control.

WIRING DIAGRAM

B183730E01

INSPECTION PROCEDURE


1. CHECK FRONT POWER SEAT OPERATION
  1. Check that each function of the power seat operates normally by using the front power seat switches.

    Result 
    Result
    Proceed to
    All front power seat switch operations are malfunctioning except lumbar support switch operation
    A
    Only lumbar support switch operation is malfunctioning
    B



B
Go to step 6
A


2. READ VALUE USING INTELLIGENT TESTER (FRONT POWER SEAT SWITCH)
  1. Using the intelligent tester, read the Data List.

    Driver Seat 
    Item
    Measurement Item/Display (Range)
    Normal Condition
    Diagnostic Note
    Reclining Rear
    Reclining switch signal (Rearward) / ON or OFF
    ON: Reclining switch (Rearward) on
    OFF: Reclining switch (Rearward) off
    -
    Reclining Front
    Reclining switch signal (Forward) / ON or OFF
    ON: Reclining switch (Forward) on
    OFF: Reclining switch (Forward) off
    -
    Front Vertical Down
    Front vertical switch signal (Downward) / ON or OFF
    ON: Front vertical switch (Downward) on
    OFF: Front vertical switch (Downward) off
    -
    Front Vertical Up
    Front vertical switch signal (Upward) / ON or OFF
    ON: Front vertical switch (Upward) on
    OFF: Front vertical switch (Upward) off
    -
    Lifter Switch Down
    Lifter switch signal (Downward) / ON or OFF
    ON: Lifter switch (Downward) on
    OFF: Lifter switch (Downward) off
    -
    Lifter Switch Up
    Lifter switch signal (Upward) / ON or OFF
    ON: Lifter switch (Upward) on
    OFF: Lifter switch (Upward) off
    -
    Slide Rear
    Sliding switch signal (Rearward) / ON or OFF
    ON: Sliding switch (Rearward) on
    OFF: Sliding switch (Rearward) off
    -
    Slide Front
    Sliding switch signal (Forward) / ON or OFF
    ON: Sliding switch (Forward) on
    OFF: Sliding switch (Forward) off
    -

    OK:
    On intelligent tester screen, each item changes between ON and OFF according to above chart.



NG
REPLACE POSITION CONTROL ECU AND SWITCH (Click here)
OK


3. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (FRONT POWER SEAT MOTOR)
  1. Using the intelligent tester, perform the Active Test.

    Driver Seat 
    Tester Display
    Test Part
    Control Range
    Diagnostic Note
    Seat Reclining
    Seat reclining operation
    Front / OFF / Rear
    -
    Front Vertical Operation
    Seat front vertical operation
    Up / OFF / Down
    -
    Lifter Operation
    Seat lifter operation
    Up / OFF / Down
    -
    Seat Slide Operation
    Seat sliding operation
    Front / OFF / Rear
    -

    OK:
    The power seat motors operate normally.



NG
Go to step 4
OK

REPLACE POSITION CONTROL ECU AND SWITCH (Click here)

4. INSPECT FRONT SEAT ASSEMBLY (FRONT POWER SEAT MOTOR)
  1. Remove the front seat assembly LH (for LHD) (Click here).

  1. Remove the front seat assembly RH (for RHD) (Click here).

  1. B188327E01
    Check operation of the slide motor.
    1. Check if the seat moves smoothly when the battery is connected to the slide motor connector terminals.

      OK:
      for LHD 
      Measurement Condition
      Specified Condition
      Battery positive (+) → 1
      Battery negative (-) → 2
      Forward
      Battery positive (+) → 2
      Battery negative (-) → 1
      Rearward
      for RHD 
      Measurement Condition
      Specified Condition
      Battery positive (+) → 2
      Battery negative (-) → 1
      Forward
      Battery positive (+) → 1
      Battery negative (-) → 2
      Rearward

  1. B188327E03
    Check operation of the front vertical motor.
    1. Check if the seat moves smoothly when the battery is connected to the front vertical motor connector terminals.

      OK:
      for LHD 
      Measurement Condition
      Specified Condition
      Battery positive (+) → 1
      Battery negative (-) → 2
      Upward
      Battery positive (+) → 2
      Battery negative (-) → 1
      Downward
      for RHD 
      Measurement Condition
      Specified Condition
      Battery positive (+) → 2
      Battery negative (-) → 1
      Upward
      Battery positive (+) → 1
      Battery negative (-) → 2
      Downward

  1. B188327E04
    Check operation of the lifter motor.
    1. Check if the seat moves smoothly when the battery is connected to the lifter motor connector terminals.

      OK:
      for LHD 
      Measurement Condition
      Specified Condition
      Battery positive (+) → 2
      Battery negative (-) → 1
      Upward
      Battery positive (+) → 1
      Battery negative (-) → 2
      Downward
      for RHD 
      Measurement Condition
      Specified Condition
      Battery positive (+) → 1
      Battery negative (-) → 2
      Upward
      Battery positive (+) → 2
      Battery negative (-) → 1
      Downward

  1. B188327E05
    Check operation of the reclining motor.
    1. Check if the seat moves smoothly when the battery is connected to the reclining motor connector terminals.

      OK:
      Measurement Condition
      Specified Condition
      Battery positive (+) → 2
      Battery negative (-) → 1
      Forward
      Battery positive (+) → 1
      Battery negative (-) → 2
      Rearward

Result 
Result
Proceed to
OK
A
NG (for LHD)
B
NG (for RHD)
C


B
REPLACE FRONT SEAT ASSEMBLY LH (Click here)

C
REPLACE FRONT SEAT ASSEMBLY RH
A


5. CHECK HARNESS AND CONNECTOR (POSITION CONTROL ECU AND SWITCH - POWER SEAT MOTOR)
B128944E04
  1. Disconnect the c14*1 or c26*2 switch connector.

  1. Disconnect the c17*1, c18*1, c19*1, c20*1 or c3*2, c4*2, c5*2, c6*2 motor connectors.

    HINT:
    *1: for LHD
    *2: for RHD

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    c14-3 (SLD-) - c17-2
    Always
    Below 1 Ω
    c14-2 (SLD+) - c17-1
    Always
    Below 1 Ω
    c14-4 (FRV-) - c19-2
    Always
    Below 1 Ω
    c14-6 (FRV+) - c19-1
    Always
    Below 1 Ω
    c14-9 (LFT-) - c18-1
    Always
    Below 1 Ω
    c14-7 (LFT+) - c18-2
    Always
    Below 1 Ω
    c14-10 (RCL-) - c20-1
    Always
    Below 1 Ω
    c14-8 (RCL+) - c20-2
    Always
    Below 1 Ω
    c14-1 (GND) - Body ground
    Always
    Below 1 Ω
    c14-3 (SLD-) or c17-2 - Body ground
    Always
    10 kΩ or higher
    c14-2 (SLD+) or c17-1 - Body ground
    Always
    10 kΩ or higher
    c14-4 (FRV-) or c19-2 - Body ground
    Always
    10 kΩ or higher
    c14-6 (FRV+) or c19-1 - Body ground
    Always
    10 kΩ or higher
    c14-9 (LFT-) or c18-1 - Body ground
    Always
    10 kΩ or higher
    c14-7 (LFT+) or c18-2 - Body ground
    Always
    10 kΩ or higher
    c14-10 (RCL-) or c20-1 - Body ground
    Always
    10 kΩ or higher
    c14-8 (RCL+) or c20-2 - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    c26-3 (SLD-) - c3-1
    Always
    Below 1 Ω
    c26-2 (SLD+) - c3-2
    Always
    Below 1 Ω
    c26-4 (FRV-) - c5-1
    Always
    Below 1 Ω
    c26-6 (FRV+) - c5-2
    Always
    Below 1 Ω
    c26-9 (LFT-) - c4-2
    Always
    Below 1 Ω
    c26-7 (LFT+) - c4-1
    Always
    Below 1 Ω
    c26-10 (RCL-) - c6-1
    Always
    Below 1 Ω
    c26-8 (RCL+) - c6-2
    Always
    Below 1 Ω
    c26-1 (GND) - Body ground
    Always
    Below 1 Ω
    c26-3 (SLD-) or c3-1 - Body ground
    Always
    10 kΩ or higher
    c26-2 (SLD+) or c3-2 - Body ground
    Always
    10 kΩ or higher
    c26-4 (FRV-) or c5-1 - Body ground
    Always
    10 kΩ or higher
    c26-6 (FRV+) or c5-2 - Body ground
    Always
    10 kΩ or higher
    c26-9 (LFT-) or c4-2 - Body ground
    Always
    10 kΩ or higher
    c26-7 (LFT+) or c4-1 - Body ground
    Always
    10 kΩ or higher
    c26-10 (RCL-) or c6-1 - Body ground
    Always
    10 kΩ or higher
    c26-8 (RCL+) or c6-2 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE POSITION CONTROL ECU AND SWITCH (Click here)

6. INSPECT LUMBAR SUPPORT SWITCH
B183731E01
  1. Remove the lumbar support switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Switch Condition
    Specified Condition
    3 (B) - 4 (H)
    Hold
    Below 1 Ω
    1 (R) - 2 (E2)
    4 (H) - 5 (E2)
    Off
    1 (R) - 2 (E2)
    4 (H) - 5 (E2)
    Release
    1 (R) - 3 (B)
    for RHD 
    Tester Connection
    Switch Condition
    Specified Condition
    3 (B) - 4 (H)
    Hold
    Below 1 Ω
    1 (R) - 2 (E)
    4 (H) - 5 (E)
    Off
    1 (R) - 2 (E)
    4 (H) - 5 (E)
    Release
    1 (R) - 3 (B)



NG
REPLACE LUMBAR SUPPORT SWITCH (Click here)
OK


7. INSPECT LUMBAR SUPPORT ADJUSTER ASSEMBLY
B107944E06
  1. Remove the lumbar support adjuster (Click here).

  1. Check operation of the lumbar support adjuster.

    1. Check that the lumbar support adjuster moves smoothly when the battery is connected to the lumbar support adjuster motor connector terminals.

      OK:
      for LHD 
      Measurement Condition
      Specified Condition
      Battery positive (+) → 1
      Battery negative (-) → 2
      Clockwise
      Battery positive (+) → 2
      Battery negative (-) → 1
      Counterclockwise
      for RHD 
      Measurement Condition
      Specified Condition
      Battery positive (+) → 2
      Battery negative (-) → 1
      Clockwise
      Battery positive (+) → 1
      Battery negative (-) → 2
      Counterclockwise



NG
REPLACE LUMBAR SUPPORT ADJUSTER ASSEMBLY (Click here)
OK


8. CHECK HARNESS AND CONNECTOR (LUMBAR SUPPORT SWITCH - BATTERY AND BODY GROUND)
B179858E02
  1. Disconnect the c16*1 or c28*2 switch connector.

    HINT:
    *1: for LHD
    *2: for RHD

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    c16-3 (B) - Body ground
    Always
    11 to 14 V
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    c28-3 (B) - Body ground
    Always
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    c16-5 (E2) - Body ground
    Always
    Below 1 Ω
    c16-2 (E2) - Body ground
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    c28-5 (E) - Body ground
    Always
    Below 1 Ω
    c28-2 (E) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (LUMBAR SUPPORT SWITCH - LUMBAR SUPPORT ADJUSTER ASSEMBLY)


← Front Power Seat does not Operate with Front Power Seat Switch (from Jan 2012)One or more Power Seat Motors do not Operate (from Jan 2012) →