2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

P0571 Brake Switch "A" Circuit

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

When the brake pedal is depressed, the stop light switch sends a signal to the ECM. When the ECM receives this signal, it cancels the cruise control. The fail-safe function operates to enable normal driving even if there is a malfunction in the stop light signal circuit. The cancellation condition occurs when voltage is applied to terminal STP. When the brake is applied, voltage is applied to terminal STP of the ECM through the STOP fuse and the stop light switch, and the ECM turns the cruise control off.
DTC Code
DTC Detection Condition
Trouble Area
P0571
When the voltage of the STP terminal and the ST1- terminal of the ECM is below than 1 V for 0.5 sec. or more.
  1. Stop light switch
  2. Stop light switch circuit
  3. ECM

WIRING DIAGRAM

E149082E03

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH)
  1. Using the intelligent tester, read the Data List.

    Cruise Control 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Stop Light SW M-CPU
    Stop light switch signal (Main CPU) / ON or OFF
    ON: Brake pedal depressed
    OFF: Brake pedal released
    -

    OK:
    Normal conditions listed above are displayed.

    Result 
    Result
    Proceed to
    OK
    (for 3UR-FE)
    A
    OK
    (for 2UZ-FE)
    B
    OK
    (for 1GR-FE)
    C
    OK
    (for 1VD-FTV)
    D
    NG
    E



B
REPLACE ECM (Click here)

C
REPLACE ECM (Click here)

D
REPLACE ECM (Click here)

E
Go to step 2
A

REPLACE ECM (Click here)

2. INSPECT STOP LIGHT SWITCH
E164228E01
  1. Remove the stop light switch (Click here for LHD, Click here for RHD).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Pin pushed
    10 kΩ or higher
    Pin not pushed
    Below 1 Ω
    3 - 4
    Pin pushed
    Below 1 Ω
    Pin not pushed
    10 kΩ or higher

    Result 
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C



B
REPLACE STOP LIGHT SWITCH (Click here)

C
REPLACE STOP LIGHT SWITCH (Click here)
A


3. CHECK HARNESS AND CONNECTOR (BATTERY - STOP LIGHT SWITCH)
E149003E01
  1. Disconnect the A30 stop light switch connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    A30-2 - Body ground
    Always
    11 to 14 V
    A30-3 - Body ground
    Ignition switch ON



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH - ECM)
E158851E01
  1. Disconnect the A30 stop light switch connector.

  1. Disconnect the A38*1 or A52*2 ECM connector.

    HINT:
    1. *1: for LHD
    2. *2: for RHD

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    A30-1 - A38-36 (STP)
    Always
    Below 1 Ω
    A30-1 - Body ground
    Always
    10 kΩ or higher
    A30-4 - A38-35 (ST1-)
    Always
    Below 1 Ω
    A30-4 - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    A30-1 - A52-36 (STP)
    Always
    Below 1 Ω
    A30-1 - Body ground
    Always
    10 kΩ or higher
    A30-4 - A52-35 (ST1-)
    Always
    Below 1 Ω
    A30-4 - Body ground
    Always
    10 kΩ or higher

    Result 
    Result
    Proceed to
    OK
    (for 3UR-FE)
    A
    OK
    (for 2UZ-FE)
    B
    OK
    (for 1GR-FE)
    C
    OK
    (for 1VD-FTV)
    D
    NG
    E



B
REPLACE ECM (Click here)

C
REPLACE ECM (Click here)

D
REPLACE ECM (Click here)

E
REPAIR OR REPLACE HARNESS OR CONNECTOR
A

REPLACE ECM (Click here)


← P0503 Vehicle Speed Sensor "A" Intermittent / Erratic / High (from Jan 2012)P0571 Brake Switch "A" Circuit (from Jan 2012) →