2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

P0443 Evaporative Emission Control System Purge Control Valve Circuit

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

DESCRIPTION

To reduce HC emissions, evaporated fuel from the fuel tank is routed through the canister to the intake manifold for combustion in the cylinders.
The ECM changes the duty signal to the purge VSV so that the intake quantity of HC emissions is appropriate for the driving conditions (engine load, engine speed, vehicle speed, etc.) after the engine is warmed up.
DTC Code
DTC Detection Condition
Trouble Area
P0443
The proper response to the ECM command does not occur (1 trip detection logic).
  1. Open or short in purge VSV circuit
  2. Purge VSV
  3. ECM

WIRING DIAGRAM

A182400E01

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when a malfunction is detected. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (PURGE VSV)
A140697E01
  1. Disconnect the vacuum hose from the purge VSV.

  1. Connect the intelligent tester to the DLC3.

  1. Start the engine and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Activate the VSV for Evap Control.

  1. Check if air is sucked into the port when operating the purge VSV using the intelligent tester.

    OK:
    Tester Operation
    Specified Condition
    VSV is ON
    Suction of air
    VSV is OFF
    No suction of air



NG
Go to step 2
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)

2. INSPECT PURGE VSV
  1. Inspect the purge VSV (Click here).



NG
REPLACE PURGE VSV (Click here)
OK


3. INSPECT PURGE VSV (POWER SOURCE VOLTAGE)

  1. A182261E02
    Disconnect the purge VSV connector.

  1. Turn the engine switch on (IG).

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    C55-2 - Body ground
    Always
    11 to 14 V



NG
Go to step 5
OK


4. CHECK HARNESS AND CONNECTOR (PURGE VSV - ECM)
A182263E02
  1. Disconnect the purge VSV connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (for LHD):
    Tester Connection
    Condition
    Specified Condition
    C55-1 - C45-63 (PRG)
    Always
    Below 1 Ω
    C55-1 or C45-63 (PRG) - Body ground
    Always
    10 kΩ or higher

    Standard Resistance (for RHD):
    Tester Connection
    Condition
    Specified Condition
    C55-1 - C46-63 (PRG)
    Always
    Below 1 Ω
    C55-1 or C46-63 (PRG) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)

5. CHECK HARNESS AND CONNECTOR (PURGE VSV - EFI NO. 2 FUSE)

  1. A182401E01
    Disconnect the purge VSV connector.

  1. Remove the EFI No. 2 fuse from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    C55-2 - EFI No. 2 fuse terminal 2
    Always
    Below 1 Ω
    C55-2 or EFI No. 2 fuse terminal 2 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK ECM POWER SOURCE CIRCUIT (Click here)


← P0420 Catalyst System Efficiency Below Threshold (Bank 1) (+ P0430) (Sep 2011 – Dec 2011)P0500 Vehicle Speed Sensor "A" (Sep 2011 – Dec 2011) →