2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

ECM Power Source Circuit

Circuit diagnosis · Vehicles built Sep 2011 – Dec 2011

DESCRIPTION

When the engine switch is turned on (IG), battery voltage is applied to terminal IGSW of the ECM. The output signal from the MREL terminal of the ECM causes a current to flow to the coil, closing the contacts of the integration relay (EFI relay) and supplying power to either terminal +B or +B2 of the ECM.

WIRING DIAGRAM

A182935E01
A182935E02

INSPECTION PROCEDURE


1. CHECK HARNESS AND CONNECTOR (BATTERY VOLTAGE)
A181322E01
  1. Remove the integration relay from the engine room relay block.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    1C-1 - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - INTEGRATION RELAY)
OK


2. INSPECT FUSES (IG2 MAIN, EFI MAIN AND IGN)
A180645E01
  1. Remove the IG2 MAIN fuse, EFI MAIN fuse and IGN fuse from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    IG2 MAIN fuse
    Always
    Below 1 Ω
    EFI MAIN fuse
    Always
    Below 1 Ω
    IGN fuse
    Always
    Below 1 Ω



NG
CHECK FOR SHORT IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE
OK


3. INSPECT INTEGRATION NO.1 RELAY (IG2, EFI)
A148742E04
  1. Remove the integration relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1C-1 - 1B-8
    Battery voltage is not applied to terminals 1B-6 and 1B-7
    10 kΩ or higher
    1C-1 - 1B-8
    Battery voltage is applied to terminals 1B-6 and 1B-7
    Below 1 Ω
    1C-1 - 1B-4
    Battery voltage is not applied to terminals 1B-2 and 1B-3
    10 kΩ or higher
    1C-1 - 1B-4
    Battery voltage is applied to terminals 1B-2 and 1B-3
    Below 1 Ω



NG
REPLACE INTEGRATION NO.1 RELAY
OK


4. CHECK HARNESS AND CONNECTOR (INTEGRATION RELAY - ECM, BATTERY AND BODY GROUND)
A185380E01
  1. Disconnect the ECM connector.

  1. Remove the integration relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (for LHD):
    Tester Connection
    Condition
    Specified Condition
    A38-28 (IGSW) - 1B-8
    Always
    Below 1 Ω
    A38-3 (+B) - 1B-4
    Always
    Below 1 Ω
    A38-2 (+B2) - 1B-4
    Always
    Below 1 Ω
    A38-34 (MREL) - 1B-2
    Always
    Below 1 Ω
    1B-3 - Body ground
    Always
    Below 1 Ω
    1B-7 - Body ground
    Always
    Below 1 Ω
    A38-28 (IGSW) or 1B-8 - Body ground
    Always
    10 kΩ or higher
    A38-3 (+B) or 1B-4 - Body ground
    Always
    10 kΩ or higher
    A38-2 (+B2) or 1B-4 - Body ground
    Always
    10 kΩ or higher
    A38-34 (MREL) or 1B-2 - Body ground
    Always
    10 kΩ or higher

    Standard Resistance (for RHD):
    Tester Connection
    Condition
    Specified Condition
    A52-28 (IGSW) - 1B-8
    Always
    Below 1 Ω
    A52-3 (+B) - 1B-4
    Always
    Below 1 Ω
    A52-2 (+B2) - 1B-4
    Always
    Below 1 Ω
    A52-34 (MREL) - 1B-2
    Always
    Below 1 Ω
    1B-3 - Body ground
    Always
    Below 1 Ω
    1B-7 - Body ground
    Always
    Below 1 Ω
    A52-28 (IGSW) or 1B-8 - Body ground
    Always
    10 kΩ or higher
    A52-3 (+B) or 1B-4 - Body ground
    Always
    10 kΩ or higher
    A52-2 (+B2) or 1B-4 - Body ground
    Always
    10 kΩ or higher
    A52-34 (MREL) or 1B-2 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. CHECK HARNESS AND CONNECTOR (ECM - BODY GROUND)
A136305E51
  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (for LHD):
    Tester Connection
    Condition
    Specified Condition
    C45-81 (E1) - Body ground
    Always
    Below 1 Ω

    Standard Resistance (for RHD):
    Tester Connection
    Condition
    Specified Condition
    C46-81 (E1) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. INSPECT ECM (IGSW VOLTAGE)
A164768E09
  1. Disconnect the ECM connectors.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage (for LHD):
    Tester Connection
    Switch Condition
    Specified Condition
    A38-28 (IGSW) - Body ground
    Engine switch on (IG)
    11 to 14 V

    Standard Voltage (for RHD):
    Tester Connection
    Switch Condition
    Specified Condition
    A52-28 (IGSW) - Body ground
    Engine switch on (IG)
    11 to 14 V



NG
Go to step 9
OK


7. REPLACE ECM
  1. Replace the ECM (Click here).


NEXT


8. CHECK PROBLEM SYMPTOM DISAPPEARS
  1. Check if the problem symptom disappears.

    Result 
    Result
    Proceed to
    Problem symptom disappears
    A
    Problem symptom does not disappear
    B



B
GO TO PROBLEM SYMPTOMS TABLE (Click here)
A

END

9. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - INTEGRATION RELAY)
A182936E01
  1. Disconnect the main body ECU connector.

  1. Remove the integration relay.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E2-11 (IG2D) - 1B-6
    Always
    Below 1 Ω
    E2-11 (IG2D) or 1B-6 - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

GO TO ENTRY AND START SYSTEM (Click here)


← U0101 Lost Communication with TCM (Sep 2011 – Dec 2011)VC Output Circuit (Sep 2011 – Dec 2011) →