2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

P0500 Vehicle Speed Sensor "A"

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

DESCRIPTION

The speed sensor detects the wheel speed and sends the appropriate signals to the skid control ECU. The skid control ECU converts these wheel speed signals into a 4-pulse signal and outputs it to the ECM via the combination meter. The ECM determines the vehicle speed based on the frequency of these pulse signals.

HINT:
  1. A voltage of 12 V or 5 V is output from each ECU and then input to the combination meter. The signal is changed to a pulse signal at the transistor in the combination meter. Each ECU controls the respective system based on the pulse signal.
  2. If a short occurs in any of the ECUs or in the wire harness connected to an ECU, all systems in the diagram below will not operate normally.

A115899E04
DTC Code
DTC Detection Condition
Trouble Area
P0500
While the vehicle is being driven, no vehicle speed sensor signal is transmitted to the ECM (2 trip detection logic).
  1. Open or short in speed signal circuit
  2. Combination meter
  3. ECM
  4. Skid control ECU

MONITOR DESCRIPTION


  1. The ECM assumes that the vehicle is being driven when the indicated vehicle speed is more than 9 km/h (5.6 mph). If there is no speed signal from the combination meter despite these conditions being met, the ECM interprets this as a malfunction in the speed signal circuit. The ECM then illuminates the MIL and stores the DTC.

WIRING DIAGRAM

A238382E03

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. CHECK OPERATION OF SPEEDOMETER
  1. Drive the vehicle and check whether the operation of the speedometer in the combination meter is normal.

    OK:
    Speedometer operation is normal.

    HINT:
    1. The vehicle speed sensor is operating normally if the speedometer reading is normal.
    2. If the speedometer does not operate, check it by following the procedure described in Speedometer Malfunction (Click here).



NG
GO TO MALFUNCTION IN SPEEDOMETER (Click here)
OK


2. READ VALUE USING INTELLIGENT TESTER (VEHICLE SPD)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

  1. Turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Data List / Vehicle Speed.

  1. Drive the vehicle.

  1. Read the value displayed on the tester.

    OK:
    Vehicle speeds displayed on tester and speedometer display are equal.



NG
Go to step 3
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)

3. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - ECM)
  1. Disconnect the combination meter connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (for LHD):
    Tester Connection
    Condition
    Specified Condition
    E7-4 (+S) - A38-13 (SPD)
    Always
    Below 1 Ω
    E7-4 (+S) or A38-13 (SPD) - Body ground
    Always
    10 kΩ or higher

    Standard Resistance (for RHD):
    Tester Connection
    Condition
    Specified Condition
    E7-4 (+S) - A52-13 (SPD)
    Always
    Below 1 Ω
    E7-4 (+S) or A52-13 (SPD) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK COMBINATION METER ASSEMBLY (+S VOLTAGE)
E154777E02
  1. Disconnect the combination meter connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E7-4 (+S) - Body ground
    Engine switch on (IG)
    4.5 to 5.5 V



NG
REPLACE ECM (Click here)
OK


5. CHECK COMBINATION METER ASSEMBLY (SPD SIGNAL WAVEFORM)
A179960E04
  1. Move the shift lever to N.

  1. Jack up the vehicle.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E7-4 (+S) - Body ground
    1. Engine switch on (IG)
    2. Wheel is turned slowly
    Voltage generated intermittently

    HINT:
    The output voltage should fluctuate up and down, similarly to the diagram, when the wheel is turned slowly.



NG
Go to step 6
OK

REPLACE ECM (Click here)

6. CHECK COMBINATION METER ASSEMBLY (SPD SIGNAL WAVEFORM)
A179960E05
  1. Move the shift lever to N.

  1. Jack up the vehicle.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E7-3 (IS) - Body ground
    1. Engine switch on (IG)
    2. Wheel is turned slowly
    Voltage generated intermittently

    Result 
    Result
    Proceed to
    NG
    A
    OK (w/ Multi-information Display)
    B
    OK (w/o Multi-information Display)
    C

    HINT:
    The output voltage should fluctuate up and down, similarly to the diagram, when the wheel is turned slowly.



B
REPLACE COMBINATION METER ASSEMBLY (Click here)

C
REPLACE COMBINATION METER ASSEMBLY (Click here)
A


7. CHECK HARNESS AND CONNECTOR (COMBINATION METER ASSEMBLY - SKID CONTROL ECU)
  1. Disconnect the combination meter connector.

  1. Disconnect the skid control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E7-3 (IS) - A24-12 (SPD)
    Always
    Below 1 Ω
    E7-3 (IS) or A24-12 (SPD) - Body ground
    Always
    10 kΩ or higher

Result 
Result
Proceed to
NG
A
OK (for LHD)
B
OK (for RHD)
C


B
REPLACE MASTER CYLINDER SOLENOID (Click here)

C
REPLACE MASTER CYLINDER SOLENOID (Click here)
A

REPAIR OR REPLACE HARNESS OR CONNECTOR


← P0443 Evaporative Emission Control System Purge Control Valve Circuit (Sep 2011 – Dec 2011)P0504 Brake Switch "A" / "B" Correlation (Sep 2011 – Dec 2011) →