2011-2013 Land Cruiser · Service Manual Audio / Visual / Telematics

Illumination Circuit

Circuit diagnosis · Vehicles built Sep 2011 – Dec 2011

DESCRIPTION

Power is supplied to the display and navigation module display, radio receiver assembly and steering pad switch assembly illumination when the light control switch is in the TAIL or HEAD position.

WIRING DIAGRAM

E194884E01

INSPECTION PROCEDURE

NOTICE:
The vehicle is equipped with an SRS (Supplemental Restraint System) which includes components such as airbags. Before servicing (including removal or installation of parts), be sure to read the Precaution in the Supplemental Restraint System (Click here).


1. CHECK ILLUMINATION
  1. Check if the illumination for the display and navigation module display, steering pad switch, glove box light, cigarette lighter, or other parts (seat heater switch, front seat memory switch, etc.) comes on when the light control switch is turned to the HEAD or TAIL position.

    Result 
    Result
    Proceed to
    Illumination comes on for all components except steering pad switch assembly.
    A
    Illumination comes on for all components except radio receiver assembly.
    B
    Illumination comes on for all components except display and navigation module display.
    C
    No illumination comes on for all components.
    D



B
Go to step 6

C
Go to step 7

D
GO TO LIGHTING SYSTEM (Click here)
A


2. CHECK HARNESS AND CONNECTOR (BATTERY - SPIRAL CABLE SUB-ASSEMBLY)

  1. E194873E01
    Disconnect the E12 spiral cable sub-assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E12-12 (IL+2) - Body ground
    Light control switch in tail or head
    11 to 14 V

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Spiral Cable Sub-assembly)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. INSPECT STEERING PAD SWITCH ASSEMBLY
E154802E03
Text in Illustration 
*1
Component without harness connected
(Steering Pad Switch Assembly)
-
-
  1. Disconnect the z36 steering pad switch assembly connector.

  1. Connect a positive (+) lead from the battery to terminal 5 (IL+2) and a negative (-) lead from the battery to terminal 8 (EAU) of the steering pad switch assembly connector.

  1. Check if the illumination for the steering pad switch assembly comes on.

    OK:
    Illumination for the steering pad switch assembly comes on.



NG
REPLACE STEERING PAD SWITCH ASSEMBLY (Click here)
OK


4. INSPECT SPIRAL CABLE SUB-ASSEMBLY

  1. E168547E27
    Disconnect the z36 and E12 spiral cable sub-assembly connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    z36-5 (IL+2) - E12-12 (IL+2)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right
    z36-8 (EAU) - E12-4 (EAU)
    Center
    Below 1 Ω
    2.5 rotations to the left
    2.5 rotations to the right

    Text in Illustration 
    *1
    Component without harness connected
    (Spiral Cable Sub-assembly)
    *2
    Steering Pad Switch Side
    *3
    Vehicle Side

    NOTICE:
    The spiral cable is an important part of the SRS airbag system. Incorrect removal or installation of the spiral cable may prevent the airbag from deploying. Be sure to read the Precaution for the supplemental restraint system (Click here).



NG
REPLACE SPIRAL CABLE SUB-ASSEMBLY (Click here)
OK


5. CHECK HARNESS AND CONNECTOR (SPIRAL CABLE - DISPLAY AND NAVIGATION MODULE DISPLAY AND RADIO RECEIVER)
  1. Disconnect the E12 spiral cable sub-assembly connector.

  1. Disconnect the F64 display and navigation module display connector.

  1. Disconnect the F56 radio receiver assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E12-12 (IL+2) - F64-12 (ILL+)
    Always
    Below 1 Ω
    E12-12 (IL+2) - F56-3 (ILL+)
    Always
    Below 1 Ω
    E12-4 (EAU) - F64-23 (SWG)
    Always
    Below 1 Ω
    E12-12 (IL+2) - Body ground
    Always
    10 kΩ or higher
    E12-4 (EAU) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

PROCEED TO NEXT SUSPECTED AREA SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

6. CHECK HARNESS AND CONNECTOR (RADIO RECEIVER - BATTERY AND BODY GROUND)
  1. Disconnect the F56 radio receiver assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    F56-3 (ILL+) - Body ground
    Light control switch in TAIL or HEAD
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F56-17 (ILL-) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE RADIO RECEIVER ASSEMBLY (Click here)

7. CHECK HARNESS AND CONNECTOR (DISPLAY AND NAVIGATION MODULE DISPLAY - BATTERY AND BODY GROUND)
  1. Disconnect the F64 and F62 display and navigation module display connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    F64-12 (ILL+) - Body ground
    Light control switch in TAIL or HEAD
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F62-1 (HILL) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE DISPLAY AND NAVIGATION MODULE DISPLAY (Click here)


← Steering Pad Switch Circuit (Sep 2011 – Dec 2011)Parking Brake Switch Circuit (Sep 2011 – Dec 2011) →