2011-2013 Land Cruiser · Service Manual Steering

B2603 Tilt and Telescopic Manual Switch Circuit Malfunction

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

Different voltage values are input to the multiplex tilt and telescopic ECU by operating the tilt and telescopic manual switch. The multiplex tilt and telescopic ECU then judges which motor and in which direction that motor should be moved based on the voltage value.
DTC Code
Detection Condition
Trouble Area
B2603
When operating the tilt and telescopic manual switch, an abnormal voltage value is input to the multiplex tilt and telescopic ECU.
  1. Tilt and telescopic manual switch
  2. Tilt and telescopic manual switch circuit
  3. Multiplex tilt and telescopic ECU

WIRING DIAGRAM

C175603E03
C175603E02

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER (TILT AND TELESCOPIC MANUAL SWITCH)
C113518E01
  1. Use the Data List to check if the tilt and telescopic manual switch is functioning properly.

    Tilt & Telescopic 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Tilt Up Switch
    Input state of tilt up by manual switch/ON or OFF
    ON: Tilt up activated by manual switch
    OFF: Tilt up not activated by manual switch
    -
    Tilt Down Switch
    Input state of tilt down by manual switch/ON or OFF
    ON: Tilt down activated by manual switch
    OFF: Tilt down not activated by manual switch
    -
    Telesco Short Switch
    Input state of telescopic short by manual switch/ON or OFF
    ON: Telescopic short activated by manual switch
    OFF: Telescopic short not activated by manual switch
    -
    Telesco Long Switch
    Input state of telescopic long by manual switch/ON or OFF
    ON: Telescopic long activated by manual switch
    OFF: Telescopic long not activated by manual switch
    -

OK:
"ON" is displayed on the intelligent tester screen when each switch is turned on.
"OFF" is displayed on the intelligent tester screen when each switch is turned off.



NG
Go to step 3
OK


2. CONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    Result 
    Result
    Proceed to
    DTC is output
    A
    DTC is not output
    B



B
USE SIMULATION METHOD TO CHECK (Click here)
A

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU (Click here)

3. CHECK HARNESS AND CONNECTOR (MULTIPLEX TILT AND TELESCOPIC ECU - HEADLIGHT DIMMER SWITCH)
C177727E01
  1. Disconnect the E27 multiplex tilt and telescopic ECU connector.

  1. Disconnect the E14 headlight dimmer switch or E15 windshield wiper switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for Headlight Dimmer Switch LH Side Type 
    Tester Connection
    Condition
    Specified Condition
    E27-4 (VC) - E14-8 (VC)
    Always
    Below 1 Ω
    E27-3 (MSW) - E14-10 (MSV)
    E14-8 (VC) - Body ground
    Always
    10 kΩ or higher
    E14-10 (MSV) - Body ground
    for Headlight Dimmer Switch RH Side Type 
    Tester Connection
    Condition
    Specified Condition
    E27-4 (VC) - E15-6 (VC)
    Always
    Below 1 Ω
    E27-3 (MSW) - E15-7 (MSV)
    E15-6 (VC) - Body ground
    Always
    10 kΩ or higher
    E15-7 (MSV) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK MULTIPLEX TILT AND TELESCOPIC ECU (VC TERMINAL VOLTAGE)

  1. C149088E18
    Reconnect the E27 multiplex tilt and telescopic ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    E27-4 (VC) - E27-3 (MSW)
    Engine switch on (IG)
    4.9 to 5.1 V



NG
REPLACE MULTIPLEX TILT AND TELESCOPIC ECU (Click here)
OK


5. INSPECT TILT AND TELESCOPIC MANUAL SWITCH

  1. C176286E01
    Remove the tilt and telescopic manual switch (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 (VC) - 3 (MSW)
    Tilt up
    342 to 378 Ω
    Tilt down
    1890.5 to 2089.5 Ω
    Telescopic contract
    750.5 to 829.5 Ω
    Telescopic extend
    152 to 168 Ω

    Result 
    Result
    Proceed to
    OK (for headlight dimmer switch LH side)
    A
    OK (for headlight dimmer switch RH side)
    B
    NG
    C



B
REPLACE WINDSHIELD WIPER SWITCH (Click here)

C
REPLACE TILT AND TELESCOPIC MANUAL SWITCH (Click here)
A

REPLACE HEADLIGHT DIMMER SWITCH (Click here)


← B2602 Key Unlock Warning Switch Circuit Malfunction (+ B2606) (from Jan 2012)B2603 Tilt and Telescopic Manual Switch Circuit Malfunction (from Jan 2012) →