2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

P0412 Secondary Air Injection System Switching Valve "A" Circuit

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

DESCRIPTION

The diagnostic trouble code (DTC) indicates an open or short in the electric air switching valve (E-ASV) circuit of the secondary air injection (AIR) system. The air injection control driver diagnoses the air pump circuit, E-ASV circuit and itself, and sends the diagnosis signal to the engine control module (ECM). If the ECM receives a malfunction signal from the air injection control driver, the ECM illuminates the malfunction indicator lamp (MIL), and stores a DTC.
The secondary air injection (AIR) system introduces fresh air into the exhaust manifold in order to reduce carbon monoxide (CO) and hydrocarbon (HC) in the exhaust emission. This system is activated just after the engine start, and is stopped when the catalyst converter is warmed-up. This system consists of the following components: 1) the air pump which sends fresh air to the exhaust manifold, 2) the electric air switching valve (E-ASV) which switches the fresh air flow, 3) the air switching valve (ASV) which switches the air passage to the exhaust manifold of each bank, 4) the vacuum switching valve (VSV) which switches the vacuum (intake manifold pressure) to operate the ASV, 5) the pressure sensor which detects the fresh air pressure and exhaust pulse, 6) the air injection control driver which controls the power sources of the air pump and E-ASV, 7) the engine control module (ECM) which controls and monitors this system.
A182943E01
DTC Code
DTC Detection Condition
Trouble Area
P0412
The ECM receives a diagnostic signal from the driver (40% duty-cycle) (1 trip detection logic).
  1. ASV circuit
  2. Air injection control driver
  3. Air switching valve

WIRING DIAGRAM

A182395E01
A182395E02

INSPECTION PROCEDURE

HINT:
Read freeze frame data using the intelligent tester. Freeze frame data records the engine conditions when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was running or stopped, if the engine was warmed up or not, if the air-fuel ratio was lean or rich, and other data from the time the malfunction occurred.


1. CHECK HARNESS AND CONNECTOR (AIR INJECTION CONTROL DRIVER - BODY GROUND)

  1. A182398E01
    Disconnect the air injection control driver connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    C61-6 (VV) or - Body ground
    20°C (68°F)
    4.5 to 5.5 Ω



NG
Go to step 2
OK

REPLACE AIR INJECTION CONTROL DRIVER (Click here)

2. INSPECT AIR SWITCHING VALVE
A182396E01
  1. Remove the intake manifold (Click here).

  1. Disconnect the Air Switching Valve (ASV) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    20°C (68°F)
    4.5 to 5.5 Ω



NG
REPLACE AIR SWITCHING VALVE (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (AIR SWITCHING VALVE - BODY GROUND)
A182397E01
  1. Remove the intake manifold (Click here).

  1. Disconnect the Air Switching Valve (ASV) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    D10-2 - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK HARNESS AND CONNECTOR (AIR SWITCHING VALVE - AIR INJECTION CONTROL DRIVER)
A121615E09
  1. Remove the intake manifold (Click here).

  1. Disconnect the air injection control driver connector.

  1. Disconnect the air switching valve connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    C61-6 (VV) - D10-1
    Always
    Below 1 Ω
    C61-6 (VV) or D10-1 - Body ground
    Always
    10 kΩ higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK FOR INTERMITTENT PROBLEMS (Click here)


← P0351 Ignition Coil "A" Primary / Secondary Circuit (+ 7 more codes) (Sep 2011 – Dec 2011)P0418 Secondary Air Injection System Control "A" Circuit (Sep 2011 – Dec 2011) →