After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
2.
DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
CAUTION:
Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).
3.
REMOVE FRONT SEAT ASSEMBLY LH
for Manual Seat: Remove the front seat assembly LH (Click here).
for Power Seat: Remove the front seat assembly LH (Click here).
4.
REMOVE FRONT SEAT ASSEMBLY RH
for Manual Seat: Remove the front seat assembly RH (Click here).
for Power Seat: Remove the front seat assembly RH (Click here).
HINT:
Use the same procedures described for the LH side.
5.
REMOVE REAR NO. 3 SEAT CUSHION HINGE COVER
Using a screwdriver, detach the 6 claws and remove the cover.
HINT:
Tape the screwdriver tip before use.
6.
REMOVE REAR NO. 5 SEAT CUSHION HINGE COVER
Using a screwdriver, detach the 7 claws and remove the cover.
HINT:
Tape the screwdriver tip before use.
7.
REMOVE REAR NO. 2 SEAT CUSHION HINGE COVER
Operate the reclining adjuster release handle to move the seat into the position shown in the illustration.
Using a screwdriver, detach the 2 claws and 2 clips, and remove the cover.
HINT:
Tape the screwdriver tip before use.
8.
REMOVE REAR NO. 4 SEAT CUSHION HINGE COVER
Using a screwdriver, detach the 2 claws and 2 clips, and remove the cover.
HINT:
Tape the screwdriver tip before use.
9.
REMOVE REAR NO. 1 SEAT ASSEMBLY LH
w/ Rear Seat Side Airbag: Disconnect the connector.
w/ Seat Heater System: Disconnect the connector.
Remove the 4 bolts and seat assembly.
NOTICE:
Be careful not to damage the vehicle body.
10.
REMOVE REAR NO. 2 SEAT CUSHION HINGE COVER
Using a screwdriver, detach the 6 claws and remove the cover.
HINT:
Tape the screwdriver tip before use.
11.
REMOVE REAR NO. 4 SEAT CUSHION HINGE COVER
Using a screwdriver, detach the 7 claws and remove the cover.
HINT:
Tape the screwdriver tip before use.
12.
REMOVE REAR NO. 1 SEAT CUSHION HINGE COVER
Operate the reclining adjuster release handle to move the seat into the position shown in the illustration.
Using a screwdriver, detach the 2 claws and 2 clips, and remove the cover.
HINT:
Tape the screwdriver tip before use.
13.
REMOVE REAR NO. 3 SEAT CUSHION HINGE COVER
Using a screwdriver, detach the 2 claws and 2 clips, and remove the cover.
HINT:
Tape the screwdriver tip before use.
14.
REMOVE REAR NO. 1 SEAT ASSEMBLY RH
w/ Rear Seat Side Airbag: Disconnect the connector.
w/ Seat Heater System: Disconnect the connector.
Remove the 4 bolts and seat assembly.
NOTICE:
Be careful not to damage the vehicle body.
15.
REMOVE INSTRUMENT SIDE PANEL LH
Place protective tape as shown in the illustration.
Text in Illustration
*1
Protective Tape
Using a moulding remover, detach the 6 claws and remove the instrument side panel.
16.
REMOVE INSTRUMENT SIDE PANEL RH (w/o Airbag Cut Off Switch)
Place protective tape as shown in the illustration.
Text in Illustration
*1
Protective Tape
Using a moulding remover, detach the 6 claws and remove the instrument side panel.
17.
REMOVE INSTRUMENT SIDE PANEL RH (w/ Airbag Cut Off Switch)
Place protective tape as shown in the illustration.
Text in Illustration
*1
Protective Tape
Using a moulding remover, detach the 6 claws.
Disconnect the connector and remove the instrument side panel.
18.
REMOVE FRONT DOOR SCUFF PLATE LH
Detach the 7 claws and 4 clips, and remove the scuff plate.
19.
REMOVE FRONT DOOR SCUFF PLATE RH
HINT:
Use the same procedures described for the LH side.
20.
REMOVE NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Floor Under Cover)
Remove the 2 screws.
Detach the 3 claws.
Disconnect the connectors and remove the No. 1 instrument panel under cover.
21.
REMOVE COWL SIDE TRIM BOARD LH
Remove the cap nut.
Detach the 2 clips and remove the cowl side trim board.
22.
REMOVE NO. 2 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Floor Under Cover)
Detach the 4 claws and remove the No. 2 instrument panel under cover.
23.
REMOVE COWL SIDE TRIM BOARD RH
Remove the cap nut.
Detach the 2 clips and remove the cowl side trim board.
24.
REMOVE REAR STEP COVER
HINT:
Use the same procedure to remove the step cover on the other side.
Detach the 2 claws and remove the step cover.
25.
REMOVE REAR DOOR SCUFF PLATE LH
Remove the screw.
Detach the 3 claws and 4 clips, and remove the scuff plate.
26.
REMOVE REAR DOOR SCUFF PLATE RH
HINT:
Use the same procedures described for the LH side.
27.
REMOVE NO. 2 AIR DUCT PLUG
Detach the 4 claws and remove the 2 plugs.
HINT:
Use the same procedures for both sides.
28.
REMOVE AIR HEATER GUIDE
Remove the 2 screws and guide.
HINT:
Use the same procedures for both sides.
29.
REMOVE AIR DUCT PLUG
Detach the 2 claws and remove the plug.
HINT:
Use the same procedures for both sides.
30.
REMOVE REAR AIR DUCT GUIDE
Remove the screw.
Detach the claw and remove the guide.
HINT:
Use the same procedures for both sides.
31.
REMOVE REAR NO. 1 SEAT PROTECTOR
Detach the clip and 4 claws, and remove the protector.
HINT:
Use the same procedures to remove the protector on the other side.
32.
REMOVE REAR NO. 2 SEAT PROTECTOR
Detach the clip and 4 claws, and remove the protector.
HINT:
Use the same procedures to remove the protector on the other side.