B15D0 MOST Communication Malfunction
Diagnostic trouble codes · Vehicles built from Jan 2012
DESCRIPTION
This DTC is stored when the MOST network cannot be established after the master unit is activated.- HINT:
- If a short occurs in a speaker circuit, the sound from the corresponding speaker will be low or almost impossible to hear. If the volume is turned up in this situation, to prevent excessive current flow due to the short circuit, the stereo component amplifier assembly stops operating when its output exceeds a certain level. When the operation of the stereo component amplifier assembly stops, the audio and visual system will not function normally. This is because MOST communication will stop due to the shut down of the amplifier causing an error in the MOST network. The stereo component amplifier assembly will start operating again when the engine switch is turned off and back on (ACC) again. However, the amplifier will stop operating again if its output exceeds a certain level.
- When the stereo component amplifier assembly stops operating and a malfunction occurs in the audio and visual system due to a short in a speaker circuit, this DTC will be stored.
- If a short occurs in a speaker circuit, the sound from the corresponding speaker will be low or almost impossible to hear. If the volume is turned up in this situation, to prevent excessive current flow due to the short circuit, the stereo component amplifier assembly stops operating when its output exceeds a certain level. When the operation of the stereo component amplifier assembly stops, the audio and visual system will not function normally. This is because MOST communication will stop due to the shut down of the amplifier causing an error in the MOST network. The stereo component amplifier assembly will start operating again when the engine switch is turned off and back on (ACC) again. However, the amplifier will stop operating again if its output exceeds a certain level.
| DTC Code |
DTC Detection Condition |
Trouble Area |
| B15D0 |
MOST network cannot be established. |
|
- *: w/ Rear Seat Entertainment System
- HINT:
- For the MOST network, the multi-media module receiver assembly is the master unit.
- Errors may occur in MOST communication between devices due to problems such as electrical noise.
- For the MOST network, the multi-media module receiver assembly is the master unit.
WIRING DIAGRAM


INSPECTION PROCEDURE
| 1. CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING) |
Check that optional components (including associated wiring) which generate radio waves are not installed.
Result Result
Proceed to
Optional components (including associated wiring) are installed.
A
Optional components (including associated wiring) are installed.
DTCs are not output.
B
- HINT:
- Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.
- These DTCs may be stored when an AVC-LAN communication error occurs due to electrical noise.
- Electrical noise from radio waves generated by optional components or the wiring for those components may affect AVC-LAN communication.
|
|
||||
| A | |
| 2. CONFIRM SYMPTOMS |
Turn the engine switch off.
Turn the engine switch on (ACC) and check if the audio system activates and if the speakers operate.
- HINT:
- Choose a source such as radio so that sound can be output from the speakers.
- If sound from the speakers is low, turn up the volume.
- Choose a source such as radio so that sound can be output from the speakers.
Result Result
Proceed to
Even after the engine switch is turned on (ACC), the audio system does not activate and sound is not output from the speakers (w/o Rear Seat Entertainment System).
A
Even after the engine switch is turned on (ACC), the audio system does not activate and sound is not output from the speakers (w/ Rear Seat Entertainment System).
B
The audio system activates when the engine switch is turned on (ACC) but the sound stops being output when the amplifier output exceeds a certain level.
C
- HINT:
- If a short occurs in a speaker circuit, the sound from the corresponding speaker will be low or almost impossible to hear. If the volume is turned up in this situation, to prevent excessive current flow due to the short circuit, the stereo component amplifier assembly stops operating when its output exceeds a certain level. When the operation of the stereo component amplifier assembly stops, the audio and visual system will not function normally. This is because MOST communication will stop due to the shut down of the amplifier causing an error in the MOST network. The stereo component amplifier assembly will start operating again when the engine switch is turned off and back on (ACC) again. However, the amplifier will stop operating again if its output exceeds a certain level.
- When the stereo component amplifier assembly stops operating and a malfunction occurs in the audio and visual system due to a short in a speaker circuit, this DTC will be stored. In this case, check each speaker circuit and repair or replace malfunctioning parts, and then recheck for DTCs.
- If a short occurs in a speaker circuit, the sound from the corresponding speaker will be low or almost impossible to hear. If the volume is turned up in this situation, to prevent excessive current flow due to the short circuit, the stereo component amplifier assembly stops operating when its output exceeds a certain level. When the operation of the stereo component amplifier assembly stops, the audio and visual system will not function normally. This is because MOST communication will stop due to the shut down of the amplifier causing an error in the MOST network. The stereo component amplifier assembly will start operating again when the engine switch is turned off and back on (ACC) again. However, the amplifier will stop operating again if its output exceeds a certain level.
|
|
||||
|
|
||||
| A | |
| 3. CHECK MOST COMMUNICATION CONNECTORS |
Display the "MOST Line Check" screen (Click here).

Check the result on the "MOST Line Check" screen.
Result Result
Proceed to
"NCON" is displayed for "AMP".
A
"OK" is displayed for all items.
B
- When "NCON" is displayed for more than 1 item, proceed to the step for the device that has the smallest node position number.
- The "MOST Line Check" screen can be displayed only when DTC B15D0 is stored.
Text in Illustration *a
Node position number for devices that use MOST communication
*b
Device name
*c
Result
- When "NCON" is displayed for more than 1 item, proceed to the step for the device that has the smallest node position number.
|
|
||||
| A | |
| 4. CONFIRM SYMPTOMS |
Check the MOST communication line connectors.
Check if the MOST communication line connector between the multi-media module receiver assembly and stereo component amplifier assembly has any connection problems (Click here).
Display the "MOST Line Check" screen and check the result (Click here).
Result Result
Proceed to
"NCON" is displayed for "AMP".
A
The screen cannot be changed to the "MOST Line Check" screen.
B
- HINT:
- When the malfunction in the MOST network is repaired, the screen cannot be changed to the "MOST Line Check" screen.
|
|
||||
| A | |
| 5. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY WAKE UP LINE) |
Disconnect the stereo component amplifier assembly connector.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
F85-8 (WUI) - Body ground
Engine switch on (ACC)
4.5 V or higher
Text in Illustration *a
Front view of wire harness connector
(to Stereo Component Amplifier Assembly)
|
|
||||
| OK | ||
| ||
| 6. CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY) |
Disconnect the F84 multi-media module receiver assembly connector.
Disconnect the F85 stereo component amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
F84-1 (WUO) - F85-8 (WUI)
Always
Below 1 Ω
F84-1 (WUO) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 7. CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY) |
Disconnect the F84 multi-media module receiver assembly connector.
Disconnect the F85 stereo component amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
F84-2 (MI+) - F85-5 (MO+)
Always
Below 1 Ω
F84-3 (MI-) - F85-6 (MO-)
Always
Below 1 Ω
F84-4 (SLDI) - F85-7 (SLDO)
Always
Below 1 Ω
F84-5 (MO+) - F85-2 (MI+)
Always
Below 1 Ω
F84-6 (MO-) - F85-3 (MI-)
Always
Below 1 Ω
F84-7 (SLDO) - F85-4 (SLDI)
Always
Below 1 Ω
F84-2 (MI+) - Body ground
Always
10 kΩ or higher
F84-3 (MI-) - Body ground
Always
10 kΩ or higher
F84-4 (SLDI) - Body ground
Always
10 kΩ or higher
F84-5 (MO+) - Body ground
Always
10 kΩ or higher
F84-6 (MO-) - Body ground
Always
10 kΩ or higher
F84-7 (SLDO) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 8. REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY |
Replace the stereo component amplifier assembly with a new or normally functioning one (Click here).
| NEXT | |
| 9. CLEAR DTC |
Clear the DTCs (Click here).
| NEXT | |
| 10. CHECK DTC |
Recheck for DTCs and check if the same DTC is output again (Click here).
- OK:
- No DTCs are output.
|
|
||||
| OK | ||
| ||
| 11. CHECK MOST COMMUNICATION CONNECTORS |
Display the "MOST Line Check" screen (Click here).

Check the result on the "MOST Line Check" screen.
Result Result
Proceed to
"NCON" is displayed for "AMP".
A
"NCON" is displayed for "RSE".
B
"OK" is displayed for all items.
C
- When "NCON" is displayed for more than 1 item, proceed to the step for the device that has the smallest node position number.
- The "MOST Line Check" screen can be displayed only when DTC B15D0 is stored.
Text in Illustration *a
Node position number for devices that use MOST communication
*b
Device name
*c
Result
- When "NCON" is displayed for more than 1 item, proceed to the step for the device that has the smallest node position number.
|
|
||||
|
|
||||
| A | |
| 12. CONFIRM SYMPTOMS |
Check the MOST communication line connectors.
Check if the MOST communication line connector between the multi-media module receiver assembly and stereo component amplifier assembly has any connection problems (Click here).
Display the "MOST Line Check" screen and check the result (Click here).
Result Result
Proceed to
"NCON" is displayed for "AMP".
A
The screen cannot be changed to the "MOST Line Check" screen.
B
- HINT:
- When the malfunction in the MOST network is repaired, the screen cannot be changed to the "MOST Line Check" screen.
|
|
||||
| A | |
| 13. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY WAKE UP LINE) |
Disconnect the stereo component amplifier assembly connector.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
F85-8 (WUI) - Body ground
Engine switch on (ACC)
4.5 V or higher
Text in Illustration *a
Front view of wire harness connector
(to Stereo Component Amplifier Assembly)
|
|
||||
| OK | ||
| ||
| 14. CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY) |
Disconnect the F84 multi-media module receiver assembly connector.
Disconnect the F85 stereo component amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
F84-1 (WUO) - F85-8 (WUI)
Always
Below 1 Ω
F84-1 (WUO) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||
| 15. CONFIRM SYMPTOMS |
Check the MOST communication line connectors.
Check if the MOST communication line connector between the multi-media module receiver assembly and stereo component amplifier assembly has any connection problems (Click here).
Display the "MOST Line Check" screen and check the result (Click here).
Result Result
Proceed to
"NCON" is displayed for "RSE".
A
The screen cannot be changed to the "MOST Line Check" screen.
B
- HINT:
- When the malfunction in the MOST network is repaired, the screen cannot be changed to the "MOST Line Check" screen.
|
|
||||
| A | |
| 16. CHECK HARNESS AND CONNECTOR (TELEVISION DISPLAY ASSEMBLY WAKE UP LINE) |
Disconnect the television display assembly connector.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
L56-8 (WUI) - Body ground
Engine switch on (ACC)
4.5 V or higher
Text in Illustration *a
Front view of wire harness connector
(to Television Display Assembly)
|
|
||||
| OK | ||
| ||
| 17. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - TELEVISION DISPLAY ASSEMBLY) |
Disconnect the F85 stereo component amplifier assembly connector.
Disconnect the L56 television display assembly connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
F85-1 (WUO) - L56-8 (WUI)
Always
Below 1 Ω
F85-1 (WUO) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||
| 18. CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY) |
Disconnect the F84 multi-media module receiver assembly connector.
Disconnect the F85 stereo component amplifier assembly connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
F84-2 (MI+) - F85-5 (MO+)
Always
Below 1 Ω
F84-3 (MI-) - F85-6 (MO-)
Always
Below 1 Ω
F84-4 (SLDI) - F85-7 (SLDO)
Always
Below 1 Ω
F84-5 (MO+) - F85-2 (MI+)
Always
Below 1 Ω
F84-6 (MO-) - F85-3 (MI-)
Always
Below 1 Ω
F84-7 (SLDO) - F85-4 (SLDI)
Always
Below 1 Ω
F84-2 (MI+) - Body ground
Always
10 kΩ or higher
F84-3 (MI-) - Body ground
Always
10 kΩ or higher
F84-4 (SLDI) - Body ground
Always
10 kΩ or higher
F84-5 (MO+) - Body ground
Always
10 kΩ or higher
F84-6 (MO-) - Body ground
Always
10 kΩ or higher
F84-7 (SLDO) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 19. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - TELEVISION DISPLAY ASSEMBLY) |
Disconnect the F85 stereo component amplifier assembly connector.
Disconnect the L56 television display assembly connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
F85-5 (MO+) - L56-2 (MI+)
Always
Below 1 Ω
F85-6 (MO-) - L56-3 (MI-)
Always
Below 1 Ω
F85-7 (SLDO) - L56-4 (SLDI)
Always
Below 1 Ω
F85-5 (MO+) - Body ground
Always
10 kΩ or higher
F85-6 (MO-) - Body ground
Always
10 kΩ or higher
F85-7 (SLDO) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 20. CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - TELEVISION DISPLAY ASSEMBLY) |
Disconnect the F84 multi-media module receiver assembly connector.
Disconnect the L56 television display assembly connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
F84-2 (MI+) - L56-5 (MO+)
Always
Below 1 Ω
F84-3 (MI-) - L56-6 (MO-)
Always
Below 1 Ω
F84-4 (SLDI) - L56-7 (SLDO)
Always
Below 1 Ω
F84-2 (MI+) - Body ground
Always
10 kΩ or higher
F84-3 (MI-) - Body ground
Always
10 kΩ or higher
F84-4 (SLDI) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 21. CLEAR DTC |
Clear the DTCs (Click here).
| NEXT | |
| 22. CHECK DTC |
Recheck for DTCs and check if the same DTC is output again (Click here).
- OK:
- No DTCs are output.
|
|
||||
| OK | ||
| ||
