2011-2013 Land Cruiser · Service Manual Audio / Visual / Telematics

B15D3 Stereo Component Amplifier Disconnected

Diagnostic trouble codes · Vehicles built from Jan 2012

DESCRIPTION

The multi-media module receiver assembly and stereo component amplifier assembly are connected by the MOST communication line.
When a MOST communication error occurs between the multi-media module receiver assembly and stereo component amplifier assembly, these DTCs will be stored.
DTC Code
DTC Detection Condition
Trouble Area
B15D3
A device that is listed in the MOST network connected device record of the master unit is missing.
  1. Stereo component amplifier assembly power source circuit
  2. MOST circuit between multi-media module receiver assembly and stereo component amplifier assembly
  3. Stereo component amplifier assembly
  4. Multi-media module receiver assembly

HINT:
For the MOST network, the multi-media module receiver assembly is the master unit.


WIRING DIAGRAM

E250950E02

INSPECTION PROCEDURE

NOTICE:
Inspect the fuses for circuits related to this system before performing the following inspection procedure.


1. CHECK OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
  1. Check for optional components.

    1. Check that optional components (including associated wiring) which generate radio waves are not installed.

      Result 
      Result
      Proceed to
      Optional components (including associated wiring) are installed.
      A
      Optional components (including associated wiring) are not installed.
      B

      HINT:
      1. Electrical noise from radio waves generated by optional components or the wiring for those components may affect MOST communication.
      2. This DTC may be stored when a MOST communication error occurs due to electrical noise.



B
Go to step 3
A


2. REMOVE OPTIONAL COMPONENTS (INCLUDING ASSOCIATED WIRING)
  1. Remove optional components (including associated wiring).

    NOTICE:
    Do not remove optional components or associated wiring without the permission of the customer.


NEXT


3. CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


4. CHECK DTC
  1. Recheck for DTCs and check if the same DTC is output again (Click here).

    OK:
    No DTCs are output.



NG
Go to step 5
OK

END (COMMUNICATION MALFUNCTION DUE TO NOISE)

5. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - BATTERY AND BODY GROUND)

  1. E240104E07
    Disconnect the stereo component amplifier assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F74-3 (GND) - Body ground
    Always
    Below 1 Ω
    F74-18 (GND2) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    F74-1 (+B) - F74-3 (GND)
    Always
    11 to 14 V
    F74-16 (+B2) - F74-3 (GND)
    Always
    11 to 14 V

Text in Illustration 
*a
Front view of wire harness connector
(to Stereo Component Amplifier Assembly)
Result 
Result
Proceed to
OK (w/o Rear Seat Entertainment System)
A
OK (w/ Rear Seat Entertainment System)
B
NG
C


B
Go to step 10

C
REPAIR OR REPLACE HARNESS OR CONNECTOR
A


6. CHECK HARNESS AND CONNECTOR (MULTI-MEDIA MODULE RECEIVER ASSEMBLY - STEREO COMPONENT AMPLIFIER ASSEMBLY)
  1. Disconnect the F84 multi-media module receiver assembly connector.

  1. Disconnect the F85 stereo component amplifier assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F84-2 (MI+) - F85-5 (MO+)
    Always
    Below 1 Ω
    F84-3 (MI-) - F85-6 (MO-)
    Always
    Below 1 Ω
    F84-4 (SLDI) - F85-7 (SLDO)
    Always
    Below 1 Ω
    F84-5 (MO+) - F85-2 (MI+)
    Always
    Below 1 Ω
    F84-6 (MO-) - F85-3 (MI-)
    Always
    Below 1 Ω
    F84-7 (SLDO) - F85-4 (SLDI)
    Always
    Below 1 Ω
    F84-2 (MI+) - Body ground
    Always
    10 kΩ or higher
    F84-3 (MI-) - Body ground
    Always
    10 kΩ or higher
    F84-4 (SLDI) - Body ground
    Always
    10 kΩ or higher
    F84-5 (MO+) - Body ground
    Always
    10 kΩ or higher
    F84-6 (MO-) - Body ground
    Always
    10 kΩ or higher
    F84-7 (SLDO) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7. REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY
  1. Replace the stereo component amplifier assembly with a new or normally functioning one (Click here).


NEXT


8. CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


Go to step 10

9. CHECK DTC
  1. Recheck for DTCs and check if the same DTC is output again (Click here).

    OK:
    No DTCs are output



NG
REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY (Click here)
OK

END (STEREO COMPONENT AMPLIFIER ASSEMBLY IS DEFECTIVE)

10. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER ASSEMBLY - MULTI-MEDIA MODULE RECEIVER AND TELEVISION DISPLAY)
  1. Disconnect the F84 multi-media module receiver assembly connector.

  1. Disconnect the F85 stereo component amplifier assembly connector.

  1. Disconnect the L56 television assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F84-5 (MO+) - F85-2 (MI+)
    Always
    Below 1 Ω
    F84-6 (MO-) - F85-3 (MI-)
    Always
    Below 1 Ω
    F84-7 (SLDO) - F85-4 (SLDI)
    Always
    Below 1 Ω
    F85-5 (MO+) - L56-2 (MI+)
    Always
    Below 1 Ω
    F85-6 (MO-) - L56-3 (MI-)
    Always
    Below 1 Ω
    F85-7 (SLDO) - L56-4 (SLDI)
    Always
    Below 1 Ω
    F85-2 (MI+) - Body ground
    Always
    10 kΩ or higher
    F85-3 (MI-) - Body ground
    Always
    10 kΩ or higher
    F85-4 (SLDI) - Body ground
    Always
    10 kΩ or higher
    F85-5 (MO+) - Body ground
    Always
    10 kΩ or higher
    F85-6 (MO-) - Body ground
    Always
    10 kΩ or higher
    F85-7 (SLDO) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


11. REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY
  1. Replace the stereo component amplifier assembly with a new or normally functioning one (Click here).


NEXT


12. CLEAR DTC
  1. Clear the DTCs (Click here).


NEXT


13. CHECK DTC
  1. Recheck for DTCs and check if the same DTC is output again (Click here).



NG
REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY (Click here)
OK

END (STEREO COMPONENT AMPLIFIER ASSEMBLY IS DEFECTIVE)


← B15D0 MOST Communication Malfunction (from Jan 2012)B15D5 Rear Seat Entertainment System Disconnected (from Jan 2012) →