2011-2013 Land Cruiser · Service Manual Drivetrain

REMOVAL

Removal / installation · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here)


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable some systems need to be initialized after the cable is reconnected (Click here).


3. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY LH

  1. B310791
    Remove the 3 bolts and screw.

  1. Turn the clip indicated by the arrow in the illustration to remove the front fender splash shield sub-assembly LH.


4. REMOVE FRONT FENDER SPLASH SHIELD SUB-ASSEMBLY RH

  1. B310792
    Remove the 3 bolts and 2 screws.

  1. Turn the clip indicated by the arrow in the illustration to remove the front fender splash shield sub-assembly RH.


5. REMOVE NO. 1 ENGINE UNDER COVER SUB-ASSEMBLY

  1. A178461
    Remove the 10 bolts and No. 1 engine under cover.


6. REMOVE NO. 2 ENGINE UNDER COVER

  1. A178462
    Remove the 2 bolts and No. 2 engine under cover.


7. REMOVE OIL PAN PROTECTOR ASSEMBLY

C171483
  1. Remove the 4 bolts and oil pan protector.


8. REMOVE FRONT FENDER APRON TRIM PACKING A

  1. A177003
    Remove the 3 clips and front fender apron seal front RH.


9. REMOVE FRONT FENDER APRON TRIM PACKING C

  1. A177002
    Remove the 4 clips and front fender apron seal rear RH.


10. DRAIN AUTOMATIC TRANSMISSION FLUID
  1. Remove the drain plug and gasket, and drain the ATF.

  1. Install a new gasket and the drain plug.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }


11. DISCONNECT FLOOR SHIFT GEAR SHIFTING ROD SUB-ASSEMBLY

C170828
  1. Remove the clip and pin, and disconnect the gear shifting rod from the transmission control shaft lever RH.


12. REMOVE FRONT PROPELLER SHAFT ASSEMBLY
(Click here)

13. REMOVE PROPELLER SHAFT ASSEMBLY
(Click here)

14. REMOVE EXHAUST PIPE (w/ DPF)
(Click here)

15. REMOVE EXHAUST PIPE (w/o DPF)
(Click here)

16. REMOVE DRIVE PLATE AND TORQUE CONVERTER CLUTCH SETTING BOLT

A170323
  1. Remove the 2 bolts and oil pan insulator.

  1. C171531
    Turn the crankshaft to gain access to the 6 bolts and remove the bolts while holding the crankshaft pulley setting bolt with a wrench.


17. DISCONNECT OIL COOLER TUBE

C177423
  1. Disconnect the 2 transmission oil cooler hoses from the oil cooler tube union.

  1. Remove the 3 bolts and separate the oil cooler tube from the engine.


18. SUPPORT AUTOMATIC TRANSMISSION ASSEMBLY

C161356
  1. Support the transmission with a transmission jack. Lift the transmission slightly from the crossmember.


19. REMOVE NO. 2 FRAME CROSSMEMBER SUB-ASSEMBLY

C171484
  1. Remove the engine mounting hole cover.

  1. C171489
    Remove the 4 bolts of the rear engine mounting insulator.

  1. C171490E01
    Remove the 4 nuts, 4 bolts and frame crossmember.


20. REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR

C172398
  1. Remove the 4 bolts and rear engine mounting insulator from the transmission.


21. DISCONNECT BREATHER PLUG HOSE

C171532
  1. Disconnect the 3 breather plug hoses from the wire harness.


22. DISCONNECT WIRE HARNESS AND CONNECTOR

C171503
  1. Remove the bolt and disconnect the ground cable.

  1. C162764E01
    Tilt the transmission downward.

    NOTICE:
    Make sure the cooling fan does not contact the fan shroud.

  1. Disconnect the park/neutral position switch connector, 2 transmission wire connectors, 2 speed sensor connectors and 2 or 3 transfer control side connectors.

    C172390E01

    HINT:
    Detach the claw, press down the lever, and then disconnect the transmission wire connector.

  1. Disconnect the 8 harness clamps.

  1. Remove the 2 bolts and disconnect the wire harness.


23. REMOVE OIL PAN COVER

C172394
  1. Remove the 2 bolts and oil pan cover.


24. REMOVE TRANSMISSION HOUSING COVER

C175581
  1. Remove the 3 bolts and transmission housing cover.


25. REMOVE AUTOMATIC TRANSMISSION ASSEMBLY

C175537
  1. Remove the 10 bolts and transmission.

    NOTICE:
    Do not use excess force to pry off the transmission assembly.


26. REMOVE TRANSFER ASSEMBLY

C171493
  1. Remove the 7 bolts and transfer case lower protector.

  1. C171523
    Remove the 8 bolts and transfer.


27. REMOVE TORQUE CONVERTER CLUTCH ASSEMBLY

28. INSPECT TORQUE CONVERTER ASSEMBLY
(Click here)
← REMOVAL (Sep 2011 – Dec 2011)INSTALLATION (Sep 2011 – Dec 2011) →