2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

VC Output Circuit

Circuit diagnosis · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

The ECM constantly generates 5 V of power from the battery voltages supplied to the +B (BATT) terminal to operate the microprocessor. The ECM also provides this power to the sensors through the VC output circuit.
A116143E67
When the VC circuit is short-circuited, the microprocessor in the ECM and sensors that are supplied with power through the VC circuit are inactivated because the power is not supplied from the VC circuit. Under this condition, the system does not start up and the MIL does not illuminate even if the system malfunctions.

HINT:
Under normal conditions, the MIL is illuminated for several seconds when the ignition switch is first turned to ON. The MIL goes off when the engine is started.


WIRING DIAGRAM

A182330E01
A182330E02

INSPECTION PROCEDURE

HINT:
When viewed from the rear of the engine assembly, Bank 1 is on the right side and Bank 2 is on the left side.


1. CHECK MIL
  1. Check that the Malfunction Indicator Lamp (MIL) lights up when turning the ignition switch to ON.

    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B



A
SYSTEM OK
B


2. CHECK COMMUNICATION BETWEEN INTELLIGENT TESTER AND ECM
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and tester on.

  1. Check the communication between the tester and ECM.

    Result 
    Result
    Proceed to
    Communication is possible
    A
    Communication is not possible
    B



A
GO TO MIL CIRCUIT (Click here)
B


3. CHECK MIL (THROTTLE BODY)
  1. Disconnect the throttle body connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the throttle body connector.



A
REPLACE THROTTLE BODY ASSEMBLY (Click here)
B


4. CHECK MIL (ACCELERATOR PEDAL POSITION SENSOR)
  1. Disconnect the accelerator pedal position sensor connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the accelerator pedal position sensor connector.



A
REPLACE ACCELERATOR PEDAL ASSEMBLY (Click here)
B


5. CHECK MIL (VVT SENSOR FOR BANK 1)
  1. Disconnect the air cleaner assembly with element (Click here).

  1. Disconnect the VVT sensor (bank 1) connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the VVT sensor (bank 1) connector.



A
REPLACE VVT SENSOR (BANK 1) (Click here)
B


6. CHECK MIL (VVT SENSOR FOR BANK 2)
  1. Disconnect the VVT sensor (bank 2) connector.

  1. Turn the ignition switch to ON.

  1. Check the MIL.

    Result 
    Result
    Proceed to
    MIL illuminates
    A
    MIL does not illuminate
    B

  1. Reconnect the VVT sensor (bank 2) connector.



A
REPLACE VVT SENSOR (BANK 2) (Click here)
B


7. CHECK HARNESS AND CONNECTOR
  1. Disconnect the throttle body connector.

  1. Disconnect the accelerator pedal position sensor connector.

  1. Disconnect the VVT sensor (bank 1) connector.

  1. Disconnect the VVT sensor (bank 2) connector.

  1. A182331E01
    Disconnect the ECM connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (Check for Short):
    for LHD 
    Tester Connection
    Condition
    Specified Condition
    A38-57 (VCPA) - Body ground
    Always
    10 kΩ or higher
    A38-58 (VCP2) - Body ground
    Always
    10 kΩ or higher
    C45-96 (VCTA) - Body ground
    Always
    10 kΩ or higher
    C45-115 (VCV1) - Body ground
    Always
    10 kΩ or higher
    C45-113 (VCV2) - Body ground
    Always
    10 kΩ or higher
    for RHD 
    Tester Connection
    Condition
    Specified Condition
    A52-57 (VCPA) - Body ground
    Always
    10 kΩ or higher
    A52-58 (VCP2) - Body ground
    Always
    10 kΩ or higher
    C46-96 (VCTA) - Body ground
    Always
    10 kΩ or higher
    C46-115 (VCV1) - Body ground
    Always
    10 kΩ or higher
    C46-113 (VCV2) - Body ground
    Always
    10 kΩ or higher

  1. Reconnect the ECM connectors.

  1. Reconnect the throttle body connector.

  1. Reconnect the accelerator pedal position sensor connector.

  1. Reconnect the VVT sensor (bank 1) connector.

  1. Reconnect the VVT sensor (bank 2) connector.



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE ECM (Click here)


← ECM Power Source Circuit (from Jan 2012)VC Output Circuit (from Jan 2012) →