2011-2013 Land Cruiser · Service Manual Brake

C1231/31 Steering Angle Sensor Circuit Malfunction

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

DESCRIPTION

The steering angle sensor signal is sent to the skid control ECU through the CAN communication system. When there is a malfunction in the communication system, it will be detected by the diagnosis function.
DTC Code
DTC Detection Condition
Trouble Area
C1231/31
When the ECU IG1 terminal voltage is 9.5 V or higher, the steering angle sensor malfunction signal is received.
  1. Steering angle sensor
  2. Harness or connector
  3. Steering angle sensor power supply
  4. CAN communication system
  5. Master cylinder solenoid (Skid control ECU)

WIRING DIAGRAM

C248799E01

INSPECTION PROCEDURE

NOTICE:
  1. When replacing the master cylinder solenoid, perform zero point calibration (Click here).
  2. Inspect the fuses for circuits related to this system before performing the following inspection procedure.

HINT:
  1. When U0073/94, U0100/65, U0114/38, U0123/62, U0124/95, U0126/63 or U0130/68 is output together with C1231/31, inspect and repair the trouble areas indicated by U0073/94, U0100/65, U0114/38, U0123/62, U0124/95, U0126/63 or U0130/68 first.
  2. When the speed sensor or the yaw rate and G sensor has trouble, DTCs of the steering angle sensor may be stored even when the steering angle sensor is normal. When DTCs of the speed sensor (C0200/31, C0205/32, C0210/33, C0215/34, C1235/35, C1236/36, C1238/38, C1239/39) or yaw rate and G sensor (C1232/32, C1234/34, C1243/43, C1244/44, C1245/45, C1381/97) are output together with DTCs of the steering angle sensor, inspect and repair the speed sensor and yaw rate and G sensor first, and then inspect and repair the steering angle sensor.


1. READ VALUE USING INTELLIGENT TESTER (STEERING ANGLE SENSOR)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the intelligent tester on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

    ABS/VSC/TRC 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Steering Angle Sensor
    Steering angle sensor / min.: -3276.8°, max.: 3276.7°
    Left turn: Increase
    Right turn: Decrease
    -

  1. Check that the steering wheel turning angle value of the steering angle sensor displayed on the intelligent tester changes when turning the steering wheel.

    OK:
    Steering angle sensor value changes.



NG
Go to step 3
OK


2. RECONFIRM DTC
  1. Clear the DTCs (Click here).

  1. Drive the vehicle at a speed of approximately 10 km/h (6 mph) or more for 10 seconds or more.

  1. Check if the same DTCs are output (Click here).

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    for LHD
    B
    for RHD
    C



B
REPLACE MASTER CYLINDER SOLENOID (Click here)

C
REPLACE MASTER CYLINDER SOLENOID (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)

3. CHECK HARNESS AND CONNECTOR (STEERING ANGLE SENSOR - BATTERY AND BODY GROUND)

  1. G030156E46
    Remove the steering wheel and the lower steering column cover.

  1. Disconnect the E11 steering angle sensor connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E11-1 (IG1) - Body ground
    Ignition switch ON
    11 to 14 V
    E11-3 (BAT) - Body ground
    Always
    11 to 14 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E11-2 (ESS) - Body ground
    Always
    Below 1 Ω

    HINT:
    1. When troubleshooting in accordance with the Diagnostic Trouble Code Chart, check DTCs before replacing the steering angle sensor (Click here).
    2. When troubleshooting in accordance with the Problem Symptoms Table, be sure to follow the table before replacing the steering angle sensor (Click here).



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE STEERING ANGLE SENSOR (Click here)


← C1225 SM Solenoid Circuit (+ 7 more codes) (from Jan 2012)C1232 Acceleration Sensor Stuck Malfunction (+ C1243, C1245, C1279) (from Jan 2012) →