ABS Warning Light Remains ON
Circuit diagnosis · Vehicles built from Jan 2012
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
DESCRIPTION
If any of the following is detected, the ABS warning light remains on.- The skid control ECU (master cylinder solenoid) connector is disconnected from the skid control ECU (master cylinder solenoid).
- There is a malfunction in the skid control ECU (master cylinder solenoid) internal circuit.
- There is an open in the harness between the combination meter and skid control ECU (master cylinder solenoid).
- The anti-lock brake system is defective.
- The voltage at terminal IG1 is high.
- The rear differential is locked.*
- *: w/ Rear Differential Lock
- HINT:
- It may not be possible to use the GTS when the skid control ECU (master cylinder solenoid) is abnormal.
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- After replacing the master cylinder solenoid, perform calibration (Click here).
| 1. CHECK THAT SKID CONTROL ECU CONNECTOR IS SECURELY CONNECTED |
Check the skid control ECU (master cylinder solenoid) connector connection.
- OK:
- The 2 connectors are securely connected.
|
|
||||
| OK | |
| 2. CHECK DTC |
Check for DTCs (Click here).
Result Result
Proceed to
DTC is not output
A
DTC is output
B
|
|
||||
| A | |
| 3. CHECK CAN COMMUNICATION LINE |
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Select CAN Bus Check from the System Selection Menu screen and follow the prompts on the screen to inspect the CAN bus.
- OK:
- CAN Bus Check indicates no malfunctions in CAN communication.
Result Result
Proceed to
OK
A
NG (for LHD)
B
NG (for RHD)
C
|
|
||||
|
|
||||
| A | |
| 4. READ VALUE USING GTS (IG1 VOLTAGE VALUE) |
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Start the engine.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
ABS/VSC/TRC Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
IG1 Voltage Value
IG1 voltage value/ Min.: 0.00 V, Max.: 20.00 V
Ignition switch ON: 11 to 14 V
-
Check the voltage output from the skid control ECU (master cylinder solenoid) displayed on the GTS.
- OK:
- The output voltage displayed on the GTS is within 11 to 14 V.
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (P TERMINAL) |
Disconnect the A24 skid control ECU (master cylinder solenoid) connector.
Measure the voltage according to the value(s) in the table below.

- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
A24-14 (P) - Body ground
Ignition switch ON
w/ Rear Differential Lock: Rear differential free
11 to 14 V
Text in Illustration *a
Front view of wire harness connector
(to Skid Control ECU [Master Cylinder Solenoid])
|
|
||||
| OK | |
| 6. PERFORM ACTIVE TEST USING GTS (ABS WARNING LIGHT) |
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Active Test.
ABS/VSC/TRC Tester Display
Test Part
Control Range
Diagnostic Note
ABS Warning Light
ABS warning light
Warning light ON/OFF
Observe the combination meter.
When performing the ABS Warning Light Active Test, check ABS Warning Light in the Data List (Click here).
ABS/VSC/TRC Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
ABS Warning Light
ABS warning light/ ON or OFF
ON: Warning light on
OFF: Warning light off
-
Result Result
Proceed to
Data List Display
Data List Display when Performing Active Test ON/OFF Operation
ON
Changes between ON and OFF
A
Does not change between ON and OFF (for LHD)
B
Does not change between ON and OFF (for RHD)
C
OFF
Changes between ON and OFF
A
Does not change between ON and OFF (for LHD)
B
Does not change between ON and OFF (for RHD)
C
|
|
||||
|
|
||||
| A | ||
| ||
| 7. CHECK HARNESS AND CONNECTOR (IG1 TERMINAL) |
Disconnect the skid control ECU (master cylinder solenoid) connector.
Measure the voltage according to the value(s) in the table below.

- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
A24-46 (IG1) - Body ground
Ignition switch ON
11 to 14 V
Text in Illustration *a
Front view of wire harness connector
(to Skid Control ECU (Master Cylinder Solenoid))
|
|
||||
| OK | |
| 8. CHECK HARNESS AND CONNECTOR (GND1, GND2 AND GND3 TERMINAL) |
Turn the ignition switch off.
Disconnect the A24 and A25 skid control ECU (master cylinder solenoid) connectors.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
A24-1 (GND1) - Body ground
Always
Below 1 Ω
A24-32 (GND2) - Body ground
Always
Below 1 Ω
A25-4 (GND3) - Body ground
Always
Below 1 Ω
Text in Illustration *a
Front view of wire harness connector
(to Skid Control ECU [Master Cylinder Solenoid])
Result Result
Proceed to
NG
A
OK (for LHD)
B
OK (for RHD)
C
|
|
||||
|
|
||||
| A | ||
| ||
| 9. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU P CIRCUIT) |
Disconnect the A24 skid control ECU (master cylinder solenoid) connector.
Disconnect the A27 4 wheel drive control ECU connector.
w/ Rear Differential Lock:Disconnect the f2 rear differential lock detection switch (No. 1 transfer indicator switch) connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
A24-14 (P) - Body ground
Always
10 kΩ or higher
Result Result
Proceed to
OK (w/o Rear Differential Lock)
A
OK (w/ Rear Differential Lock)
B
NG
C
|
|
||||
|
|
||||
| A | |
| 10. CHECK HARNESS AND CONNECTOR (P TERMINAL) |
Disconnect the A24 skid control ECU (master cylinder solenoid) connector.
Connect the A27 4 wheel drive control ECU connector.
Measure the voltage according to the value(s) in the table below.

- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
A24-14 (P) - Body ground
Ignition switch ON
11 to 14 V
Text in Illustration *a
Front view of wire harness connector
(to Skid Control ECU [Master Cylinder Solenoid])
Result Result
Proceed to
NG
A
OK (for LHD)
B
OK (for RHD)
C
|
|
||||
|
|
||||
| A | ||
| ||
| 11. INSPECT REAR DIFFERENTIAL LOCK DETECTION SWITCH (NO. 1 TRANSFER INDICATOR SWITCH) |
Remove the rear differential lock detection switch (No. 1 transfer indicator switch) (Click here).
Inspect the rear differential lock detection switch (No. 1 transfer indicator switch) (Click here).
|
|
||||
| OK | |
| 12. CHECK HARNESS AND CONNECTOR (P TERMINAL) |
Disconnect the A24 skid control ECU (master cylinder solenoid) connector.
Connect the A27 4 wheel drive control ECU connector.
Measure the voltage according to the value(s) in the table below.

- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
A24-14 (P) - Body ground
Ignition switch ON
11 to 14 V
Text in Illustration *a
Front view of wire harness connector
(to Skid Control ECU [Master Cylinder Solenoid])
Result Result
Proceed to
NG
A
OK (for LHD)
B
OK (for RHD)
C
|
|
||||
|
|
||||
| A | ||
| ||
