2011-2013 Land Cruiser · Service Manual Brake

C1202/58 Brake Fluid Level Low / Open Circuit in Brake Fluid Level Warning Switch Circuit

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

DESCRIPTION

The brake fluid level warning switch sends the appropriate signal to the skid control ECU when the brake fluid level drops.
DTC Code
DTC Detection Condition
Trouble Area
C1202/58
When either of the following conditions is detected:
  1. The fluid level of the reservoir is LOW for 4 seconds, or 40 seconds after the ignition switch is turned to ON, or for 7 seconds during pump motor operation.
  2. With the ECU terminal IG1 voltage at 9.5 V to 17.0 V, an open in the brake fluid level warning switch circuit continues for 2 seconds or more.
  1. Brake fluid level
  2. Brake fluid level warning switch
  3. Harness or connector
  4. Master cylinder solenoid (Skid control ECU)

WIRING DIAGRAM

C173284E02

INSPECTION PROCEDURE

NOTICE:
When replacing the master cylinder solenoid, perform zero point calibration (Click here).

HINT:
When C1241/41 is output together with C1202/58, inspect and repair the trouble areas indicated by C1241/41 first.


1. CHECK BRAKE FLUID LEVEL
  1. Turn the ignition switch off.

  1. Depress the brake pedal 20 times or more (until the pedal reaction feels light and pedal stroke becomes longer).

  1. Check the amount of fluid in the brake reservoir.

    HINT:
    When the ignition switch is turned to ON, brake fluid is sent to the accumulator and the fluid level decreases by approximately 10 mm (0.394 in.) from the level when the ignition switch is off (normal).

    OK:
    Brake fluid level is normal.



NG
CHECK AND REPAIR BRAKE FLUID LEAKAGE (Click here)
OK


2. INSPECT BRAKE FLUID LEVEL WARNING SWITCH

  1. C173352E05
    Disconnect the A26 brake fluid level warning switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    HINT:
    1. A float is placed inside the reservoir. Its position can be changed by increasing/decreasing the level of brake fluid.
    2. The warning switch is switched on/off at +/-5 mm (+/-0.197 in.) from the MIN level.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Float UP (Switch off)
    1.9 to 2.1 kΩ
    1 - 2
    Float DOWN (Switch on)
    Below 1 Ω

    Result
    Proceed to
    OK
    A
    NG
    for LHD
    B
    for RHD
    C

    HINT:
    If there is no problem after finishing the above check, adjust the brake fluid level to the MAX level.



B
REPLACE BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY (Click here)

C
REPLACE BRAKE MASTER CYLINDER RESERVOIR SUB-ASSEMBLY (Click here)
A


3. CHECK HARNESS AND CONNECTOR (BRAKE FLUID LEVEL WARNING SWITCH - SKID CONTROL ECU)

  1. C173353E03
    Disconnect the A24 skid control ECU connector and A26 brake fluid level warning switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A24-41 (LBL) - A26-2 (LBL)
    Always
    Below 1 Ω
    A24-41 (LBL) - Body ground
    Always
    10 kΩ or higher
    A26-1 (GND) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. RECONFIRM DTC
  1. Clear the DTC (Click here).

  1. Drive the vehicle at a speed of approximately 32 km/h (20 mph) or more for 60 seconds or more.

  1. Check if the same DTC is output (Click here).

    HINT:
    Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    for LHD
    B
    for RHD
    C



B
REPLACE MASTER CYLINDER SOLENOID (Click here)

C
REPLACE MASTER CYLINDER SOLENOID (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)


← C1201/51 Engine Control System Malfunction (Sep 2011 – Dec 2011)C1203 ECM Communication Circuit Malfunction (from Jan 2012) →