C1243 Acceleration Sensor Stuck Malfunction
Diagnostic trouble codes · Vehicles built from Jan 2012
Also covers:
- C1245 Acceleration Sensor Output Malfunction
- C1279 Acceleration Sensor Output Voltage Malfunction (Test Mode DTC)
- C1381 Acceleration Sensor Power Supply Voltage Malfunction
- C1418 Open or Short in Acceleration Sensor Circuit
DESCRIPTION
The skid control ECU (master cylinder solenoid) receives signals from the deceleration sensor. If the sensor functions abnormally, the ABS warning light turns on.| DTC Code |
DTC Detection Condition |
Trouble Area |
| C1243 |
The following condition repeats 16 times.
|
|
| C1245 |
The following condition continues for at least 60 seconds.
|
|
| C1381 |
At a vehicle speed of more than 3 km/h (2 mph), the deceleration sensor power source malfunction signal is received for 10 seconds or more. |
|
| C1418 |
One of the following conditions is met when the voltage at terminal IG1 is 9.5 V or higher:
|
|
| C1279 |
Stored during test mode. |
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- After replacing the deceleration sensor, perform zero point calibration (Click here).
| 1. CHECK DECELERATION SENSOR INSTALLATION |
Check that the deceleration sensor is installed properly.
Result Result
Proceed to
The sensor is tightened to the specified torque.
The sensor is not tilted.
A
The sensor is not tightened to the specified torque.
Or the sensor is tilted.
B
|
|
||||
| A | |
| 2. READ VALUE USING GTS (DECELERATION SENSOR) |
Turn the ignition switch off.
Connect the GTS to the DLC3.
Start the engine.
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
ABS/VSC/TRC Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Deceleration Sensor
Deceleration sensor reading / min.: -18.525 m/s2, max.: 18.387 m/s2
Approximately -1.28 to 1.27 m/s2 while stationary
The reading changes when the vehicle is bounced.
Check the Data List for proper functioning of the deceleration sensor.
- OK:
- Deceleration value changes.
|
|
||||
| OK | |
| 3. CHECK DTC |
Install the deceleration sensor to the vehicle.
Clear the DTCs (Click here).
Turn the ignition switch off.
Drive the vehicle at 6 km/h (4 mph) or more.
Check if the same DTCs are output (Click here).
Result Result
Proceed to
DTC is not output
A
DTC is output (for LHD)
B
DTC is output (for RHD)
C
|
|
||||
|
|
||||
| A | ||
| ||
| 4. INSPECT DECELERATION SENSOR |
![]() ![]() |
Remove the deceleration sensor (Click here).
Connect 3 dry cell batteries of 1.5 V in series.
- NOTICE:
- Do not apply 6 V or more to terminals 3 (VGS) and 2 (GGND).
Check the output voltage of terminal 1 (GL1) when the sensor is tilted forward and rearward.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
1 (GL1) - Battery negative (-) lead
Horizontal
Approximately 2.5 V
Tilted forward
Approximately 0.5 to 2.5 V
Tilted rearward
Approximately 2.5 to 4.5 V
Text in Illustration *a
Component without harness connected
(Deceleration Sensor)
*b
Front
*c
Tilted forward
*d
Tilted rearward
- HINT:
- If the sensor is tilted too much, it may output the wrong value.
- If the voltage drops, the sensor should be replaced with a new one.
- When replacing the sensor, it should not be placed upside down.
- If the sensor is tilted too much, it may output the wrong value.
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - DECELERATION SENSOR) |
Disconnect the A24 skid control ECU (master cylinder solenoid) connector.
Disconnect the E88 deceleration sensor connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
A24-39 (GL1) - E88-1 (GL1)
Always
Below 1 Ω
A24-23 (GGND) - E88-2 (GGND)
Always
Below 1 Ω
A24-22 (VGS) - E88-3 (VGS)
Always
Below 1 Ω
E88-1 (GL1) - Body ground
Always
10 kΩ or higher
E88-2 (GGND) - Body ground
Always
10 kΩ or higher
E88-3 (VGS) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 6. CHECK DTC |
Install the deceleration sensor to the vehicle.
Clear the DTCs (Click here).
Turn the ignition switch off.
Drive the vehicle at 6 km/h (4 mph) or more.
Check if the same DTCs are output (Click here).
Result Result
Proceed to
DTC is not output
A
DTC is output (for LHD)
B
DTC is output (for RHD)
C
|
|
||||
|
|
||||
| A | ||
| ||

