2011-2013 Land Cruiser · Service Manual Brake

C1243/43 Acceleration Sensor Stuck Malfunction

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Also covers:

DESCRIPTION

The skid control ECU receives signals from the G sensor. If the sensor functions abnormally, the ABS warning light turns on.
DTC Code
DTC Detection Condition
Trouble Area
C1243/43
The following condition repeats 16 times.
  1. GL1 and GL2 do not change when the vehicle decelerates from 30 km/h (19 mph) to 0 km/h (0 mph).
  1. G sensor
  2. Harness or connector
  3. CAN communication system
C1244/44
When either of the following conditions is detected:
1. Both of the following conditions continue for at least 60 seconds.
  1. The vehicle is stopped.
  2. The difference between GL1 and GL2 does not drop to less than 0.4 G after it reaches 0.6 G or more.
2. A data malfunction signal is received from the G sensor.
  1. G sensor
  2. Harness or connector
  3. CAN communication system
C1245/45
The following condition continues for at least 60 seconds.
  1. The difference between the values calculated from the G sensor value and vehicle speed exceeds 0.35 G.
  1. G sensor
  2. Harness or connector
  3. CAN communication system
C1381/97
A G sensor power source malfunction signal is received for at least 10 seconds at a speed of more than 3 km/h (2 mph).
  1. G sensor
  2. Harness or connector
  3. CAN communication system

WIRING DIAGRAM

C177519E01

INSPECTION PROCEDURE

NOTICE:
When replacing the G sensor, perform zero point calibration (Click here).


1. CHECK G SENSOR INSTALLATION
  1. Check that the G sensor is installed properly.

    Result:
    Result
    Proceed to
    The sensor is tightened to the specified torque.
    The sensor is not tilted.
    A
    The sensor is not tightened to the specified torque.
    Or the sensor is tilted.
    for Automatic Transmission
    B
    for Manual Transmission
    C



B
INSTALL G SENSOR CORRECTLY (Click here)

C
INSTALL G SENSOR CORRECTLY (Click here)
A


2. READ VALUE USING INTELLIGENT TESTER (DECELERATION SENSOR)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the ignition switch to ON and turn the intelligent tester on.

  1. Enter the following menus: Chassis / ABS/VSC/TRC / Data List.

ABS/VSC/TRC 
Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Deceleration Sensor
G sensor reading / min.: -18.525 m/s2, max.: 18.387 m/s2
Approximately -1.28 to 1.27 m/s2 while stationary
The reading changes when the vehicle is bounced.
  1. Check the Data List for proper functioning of the G sensor.

    OK:
    Deceleration value changes.



NG
Go to step 4
OK


3. CHECK DTC
  1. Install the G sensor to the vehicle.

  1. Clear the DTCs (Click here).

  1. Drive the vehicle at 6 km/h (4 mph) or more.

  1. Check if the same DTCs are output (Click here).

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    LHD
    B
    RHD
    C



B
REPLACE MASTER CYLINDER SOLENOID (Click here)

C
REPLACE MASTER CYLINDER SOLENOID (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)

4. INSPECT G SENSOR

  1. C108887E01
    Remove the G sensor (Click here).

  1. Connect 3 dry cell batteries of 1.5 V in series.

    NOTICE:
    Do not apply 6 V or more to terminals 3 (VGS) and 2 (GGND).

  1. Check the output voltage of terminal 1 (GL1) when the sensor is tilted forward and rearward.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    1 (GL1) - Battery negative (-) lead
    Horizontal
    Approximately 2.5 V
    1 (GL1) - Battery negative (-) lead
    Tilted forward
    Approximately 0.5 to 2.5 V
    1 (GL1) - Battery negative (-) lead
    Tilted rearward
    Approximately 2.5 to 4.5 V

    HINT:
    1. If the sensor is tilted too much, it may output the wrong value.
    2. If the voltage drops, the sensor should be replaced with a new one.
    3. When replacing the sensor, it should not be placed upside down.



NG
REPLACE DECELERATION SENSOR (Click here)
OK


5. CHECK HARNESS AND CONNECTOR (SKID CONTROL ECU - G SENSOR)

  1. C177520E01
    Disconnect the A24 skid control ECU connector.

  1. Disconnect the E88 G sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A24-39 (GL1) - E88-1 (GL1)
    Always
    Below 1 Ω
    A24-23 (GGND) - E88-2 (GGND)
    Always
    Below 1 Ω
    A24-22 (VGS) - E88-3 (VGS)
    Always
    Below 1 Ω
    E88-1 (GL1) - Body ground
    Always
    10 kΩ or higher
    E88-2 (GGND) - Body ground
    Always
    10 kΩ or higher
    E88-3 (VGS) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


6. CHECK DTC
  1. Install the G sensor to the vehicle.

  1. Clear the DTCs (Click here).

  1. Drive the vehicle at 6 km/h (4 mph) or more.

  1. Check if the same DTCs are output (Click here).

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    LHD
    B
    RHD
    C



B
REPLACE MASTER CYLINDER SOLENOID (Click here)

C
REPLACE MASTER CYLINDER SOLENOID (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)


← C1243 Acceleration Sensor Stuck Malfunction (+ C1245, C1279, C1381, C1418) (from Jan 2012)C1246/46 Master Cylinder Pressure Sensor Malfunction (Sep 2011 – Dec 2011) →