2011-2013 Land Cruiser · Service Manual Brake

C1242/42 IG2 Power Source Circuit

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

DESCRIPTION

If there is a problem with the master cylinder solenoid (skid control ECU) power supply circuit, the skid control ECU stores DTCs and prohibits operation under the fail-safe function.
If the voltage supplied to the IG2 terminal is within the DTC detection range due to malfunctions in components such as the battery and alternator circuit, this DTC is stored.
DTC Code
DTC Detection Condition
Trouble Area
C1242/42
The vehicle speed is 3 km/h (1.9 mph) or more and the voltage of the ECU IG2 terminal remains below 6.5 V for more than 7 seconds.
  1. Battery
  2. IGN fuse
  3. Charging system
  4. Harness or connector
  5. Master cylinder solenoid (Skid control ECU)

WIRING DIAGRAM

C173290E01

INSPECTION PROCEDURE

NOTICE:
When replacing the master cylinder solenoid, perform zero point calibration (Click here).


1. INSPECT BATTERY
  1. Check the battery voltage.

    Standard voltage:
    11 to 14 V

    Result 
    Result
    Proceed to
    OK
    A
    NG
    1GR-FE
    B
    2UZ-FE
    C
    1VD-FTV
    D



B
GO TO CHARGING SYSTEM (ON-VEHICLE INSPECTION) (Click here)

C
GO TO CHARGING SYSTEM (ON-VEHICLE INSPECTION) (Click here)

D
GO TO CHARGING SYSTEM (ON-VEHICLE INSPECTION) (Click here)
A


2. INSPECT IGN FUSE

  1. C176465E01
    Remove the IGN fuse from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    IGN fuse
    Always
    Below 1 Ω



NG
REPLACE IGN FUSE
OK


3. INSPECT SKID CONTROL ECU (IG2 TERMINAL)
  1. Install the IGN fuse.

  1. C173360E02
    Disconnect the A25 skid control ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    A25-1 (IG2) - Body ground
    Ignition switch ON
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. INSPECT SKID CONTROL ECU (GND TERMINAL)

  1. C124799E41
    Disconnect the A24 and A25 skid control ECU connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    A24-1 (GND1) - Body ground
    Always
    Below 1 Ω
    A24-32 (GND2) - Body ground
    Always
    Below 1 Ω
    A25-4 (GND3) - Body ground
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. RECONFIRM DTC
  1. Clear the DTC (Click here).

  1. Check if the same DTC is output (Click here).

    HINT:
    Reinstall the sensors, connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.

    Result 
    Result
    Proceed to
    DTC is not output
    A
    DTC is output
    LHD
    B
    RHD
    C



B
REPLACE MASTER CYLINDER SOLENOID (Click here)

C
REPLACE MASTER CYLINDER SOLENOID (Click here)
A

USE SIMULATION METHOD TO CHECK (Click here)


← C1242 Open Circuit in IG1/IG2 Power Source Circuit (from Jan 2012)C1243 Acceleration Sensor Stuck Malfunction (+ C1245, C1279, C1381, C1418) (from Jan 2012) →