C1252 Brake Booster Pump Motor on Time Abnormally Long
Diagnostic trouble codes · Vehicles built from Jan 2012
DESCRIPTION
The motor relay (semiconductor relay) is built into the master cylinder solenoid and drives the pump motor based on a signal from the skid control ECU (master cylinder solenoid).| DTC Code |
DTC Detection Condition |
Trouble Area |
| C1252 |
The motor operates for 3 minutes or more. |
|
- HINT:
- The pump motor continues operation for the first 3 minutes, and then starts and stops repeatedly.
INSPECTION PROCEDURE
- NOTICE:
- After replacing the master cylinder solenoid, perform zero point calibration (Click here).
- HINT:
- When DTC C1253, C1254, C1256 or C1452 is output together with DTC C1252, inspect and repair the trouble area indicated by DTC C1253, C1254, C1256 or C1452 first.
| 1. CHECK PUMP MOTOR OPERATION |
Turn the ignition switch off.
Depress the brake pedal more than 40 times.
Turn the ignition switch to ON.
Check how the pump motor operates.
Result Result
Proceed to
Pump motor does not operate
A
Pump motor operates continuously and does not stop
B
Pump motor operates intermittently
C
Pump motor operates, and then stops
D
- HINT:
- Refer to the hydraulic brake booster assembly installation procedures:
- for LHD (Click here)
- for RHD (Click here)
- for LHD (Click here)
|
|
||||
|
|
||||
|
|
||||
| A | |
| 2. CHECK CONNECTION OF PUMP MOTOR WIRE HARNESS |
Remove the hydraulic brake booster assembly (for LHD: Click here, for RHD: Click here).
Check the tightening torque of the 2 screws which secure the wire harness connecting the master cylinder solenoid and brake booster with accumulator pump assembly (for LHD: Click here, for RHD: Click here).
- OK:
- The harness is tightened to the specified torque.
|
|
||||
| OK | |
| 3. CHECK RESISTANCE OF PUMP MOTOR WIRE HARNESS |
Using a screwdriver, remove the 2 screws and pull out the wire harness from the master cylinder solenoid.
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Condition
Specified Condition
Red wire terminal - Black wire terminal
Always
Below 2 Ω
Text in Illustration *1
Pump motor wire harness
*a
Red wire
*b
Black wire
- HINT:
-
Refer to the brake booster with accumulator pump assembly installation procedures:
- for LHD (Click here)
- for RHD (Click here)
- for LHD (Click here)
|
|
||||
| OK | |
| 4. READ VALUE USING GTS (ACCUMULATOR SENSOR) |
Turn the ignition switch off.
Connect the GTS to the DLC3.
Turn the ignition switch to ON.
Turn the GTS on.
Enter the following menus: Chassis / ABS/VSC/TRC / Data List.
ABS/VSC/TRC Tester Display
Measurement Item/Range
Normal Condition
Diagnostic Note
Accumulator Sensor
Accumulator pressure sensor reading/ Min.: 0.00 V, Max.: 5.00 V
3.58 to 5 V
If the value is constant regardless of the pump operation, an accumulator pressure sensor malfunction is suspected.
Check the accumulator output value.
Result Result
Proceed to
Output value is within "Normal Condition" range
A
Output value is out of "Normal Condition" range
B
Output value is constant regardless of pump operation
C
- HINT:
- Refer to the hydraulic brake booster assembly installation procedures:
for LHD (Click here)
for RHD (Click here)
- Refer to the master cylinder solenoid installation procedures:
for LHD (Click here)
for RHD (Click here)
- Refer to the hydraulic brake booster assembly installation procedures:
|
|
||||
|
|
||||
| A | |
| 5. RECONFIRM DTC |
Clear the DTCs (Click here).
Turn the ignition switch off.
Turn the ignition switch to ON.
Wait for more than 5 minutes.
Check if the same DTC is output (Click here).
Result Result
Proceed to
DTC is output
A
DTC is not output
B
- HINT:
- Reinstall the sensors, reconnect the connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.
- Refer to the hydraulic brake booster assembly installation procedures:
for LHD (Click here)
for RHD (Click here)
- Refer to the brake booster with accumulator pump assembly installation procedures:
for LHD (Click here)
for RHD (Click here)
- Reinstall the sensors, reconnect the connectors, etc. and restore the previous vehicle conditions before rechecking for DTCs.
|
|
||||
| A | ||
| ||
