Stop Light Circuit
Circuit diagnosis · Vehicles built from Jan 2012
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
DESCRIPTION
When the stop light switch is turned on, current flows to the stop lights to illuminate them.WIRING DIAGRAM




INSPECTION PROCEDURE
| 1. READ VALUE USING INTELLIGENT TESTER (STOP LIGHT SWITCH) |
 |
Operate the intelligent tester according to the display and select the "Data List".
Main Body
Tester Display
|
Measurement Item/Range
|
Normal Condition
|
Diagnostic Note
|
Stop Light SW
|
Stop light switch / ON or OFF
|
ON: Brake pedal depressed OFF: Brake pedal released
|
-
|
- OK:
- On the intelligent tester screen, each item changes between ON and OFF according to above chart
|
NG |
 |
|
|
|
| OK |
|
 |
|
| 2. CHECK HARNESS AND CONNECTOR (STOP LIGHT CONTROL RELAY - BATTERY AND BODY GROUND) |
 |
- Disconnect the A39 relay connector.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
|
Condition
|
Specified Condition
|
A39-6 (+B) - Body ground
|
Always
|
11 to 14 V
|
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
A39-4 (GND) - Body ground
|
Always
|
Below 1 Ω
|
|
NG |
 |
|
| REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
| OK |
|
 |
|
| 3. CHECK HARNESS AND CONNECTOR (STOP LIGHT CONTROL RELAY - STOP LIGHT SWITCH) |
 |
- Disconnect the A30 stop light switch connector.
Disconnect the A39 relay connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
A30-1 - A39-2 (STP)
|
Always
|
Below 1 Ω
|
A30-1 - Body ground
|
Always
|
10 kΩ or higher
|
|
NG |
 |
|
| REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
| OK |
|
 |
|
| 4. CHECK VEHICLE TYPE |
 |
Check the vehicle type.
Result
Result
|
Proceed to
|
w/ VSC
|
A
|
w/o VSC
|
B
|
|
B |
 |
|
|
|
| A |
|
 |
|
| 5. INSPECT FUSE (ECU-IG No.2 FUSE) |
 |
Remove the ECU-IG No.2 fuse from the main body ECU.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
ECU-IG No.2 fuse
|
Always
|
Below 1 Ω
|
|
NG |
 |
|
|
|
| OK |
|
 |
|
| 6. INSPECT BRAKE LIGHT RELAY (BRK LP RELAY) |
 |
- Remove the brake light relay from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
3 - 5
|
Battery voltage not applied to terminals 1 and 2
|
10 kΩ or higher
|
Battery voltage applied to terminals 1 and 2
|
Below 1 Ω
|
3 - 4
|
Battery voltage not applied to terminals 1 and 2
|
Below 1 Ω
|
Battery voltage applied to terminals 1 and 2
|
10 kΩ or higher
|
|
NG |
 |
|
| REPLACE BRAKE LIGHT RELAY (BRK LP RELAY) (Click here)
|
|
|
| OK |
|
 |
|
| 7. CHECK HARNESS AND CONNECTOR (STOP LIGHT CONTROL RELAY - BRAKE LIGHT RELAY) |
 |
Remove the brake light relay from the engine room relay block.

Disconnect the A39 stop light control relay connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
A39-8 (OUT) - Brake light relay terminal 4
|
Always
|
Below 1 Ω
|
A39-6 (+B) - Brake light relay terminal 5
|
A39-8 (OUT) - Body ground
|
Always
|
10 kΩ or higher
|
A39-6 (+B) - Body ground
|
|
NG |
 |
|
| REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
| OK |
|
 |
|
| 8. CHECK HARNESS AND CONNECTOR (BRAKE LIGHT RELAY - BATTERY) |
 |
- Remove the brake light relay from the engine room relay block.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
|
Switch Condition
|
Specified Condition
|
Brake light relay terminal 1 - Body ground
|
Ignition switch ON
|
11 to 14 V
|
Ignition switch off
|
Below 1 V
|
|
NG |
 |
|
| REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
| OK |
|
 |
|
| 9. CHECK HARNESS AND CONNECTOR (BRAKE LIGHT RELAY - SKID CONTROL ECU) |
 |
Remove the brake light relay from the engine room relay block.

Disconnect the A24 ECU connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
Brake light relay terminal 2 - A24-16 (STPO)
|
Always
|
Below 1 Ω
|
Brake light relay terminal 2 - Body ground
|
Always
|
10 kΩ or higher
|
|
NG |
 |
|
| REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
| OK |
|
 |
|
| 10. CHECK VEHICLE TYPE |
 |
Check the vehicle type.
Result
Result
|
Proceed to
|
for Double Swing Out Type
|
A
|
except Double Swing Out Type
|
B
|
|
B |
 |
|
|
|
| A |
|
 |
|
| 11. CHECK HARNESS AND CONNECTOR (BRAKE LIGHT RELAY - STOP LIGHT AND BODY GROUND) |
 |
Remove the brake light relay from the engine room relay block.

for LH:
Disconnect the n1 light connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
Brake light relay terminal 3 - n1-2 (STP)
|
Always
|
Below 1 Ω
|
n1-4 (E) - Body ground
|
n1-2 (STP) - Body ground
|
Always
|
10 kΩ or higher
|
for RH:
Disconnect the Y1 light connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
Brake light relay terminal 3 - Y1-2 (STP)
|
Always
|
Below 1 Ω
|
Y1-6 (E) - Body ground
|
Y1-2 (STP) - Body ground
|
Always
|
10 kΩ or higher
|
Disconnect the T1 light connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
Brake light relay terminal 3 - T1-1 (B)
|
Always
|
Below 1 Ω
|
T1-2 (E) - Body ground
|
T1-1 (B) - Body ground
|
Always
|
10 kΩ or higher
|
|
NG |
 |
|
| REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
| OK |
|
 |
|
| 12. CHECK STOP LIGHT CONTROL RELAY ASSEMBLY |
 |
Temporarily replace the stop light control relay with a new or normally functioning one.
Check the stop light operation.
- OK:
- Stop light operation is normal.
|
NG |
 |
|
|
|
| OK |
|
 |
|
| REPLACE STOP LIGHT CONTROL RELAY ASSEMBLY (Click here)
|
|
| 13. CHECK HARNESS AND CONNECTOR (BRAKE LIGHT RELAY - STOP LIGHT AND BODY GROUND) |
 |
Remove the brake light relay from the engine room relay block.

for LH:
Disconnect the K4 light connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
Brake light relay terminal 3 - K4-5 (STP)
|
Always
|
Below 1 Ω
|
K4-3 (E) - Body ground
|
K4-5 (STP) - Body ground
|
Always
|
10 kΩ or higher
|
for RH:
Disconnect the L3 light connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
Brake light relay terminal 3 - L3-5 (STP)
|
Always
|
Below 1 Ω
|
L3-3 (E) - Body ground
|
L3-5 (STP) - Body ground
|
Always
|
10 kΩ or higher
|
Disconnect the S4 light connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
Brake light relay terminal 3 - S4-1 (B)
|
Always
|
Below 1 Ω
|
S4-2 (E) - Body ground
|
S4-1 (B) - Body ground
|
Always
|
10 kΩ or higher
|
|
NG |
 |
|
| REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
| OK |
|
 |
|
| 14. CHECK STOP LIGHT CONTROL RELAY ASSEMBLY |
 |
Temporarily replace the stop light control relay with a new or normally functioning one.
Check the stop light operation.
- OK:
- Stop light operation is normal.
|
NG |
 |
|
|
|
| OK |
|
 |
|
| REPLACE STOP LIGHT CONTROL RELAY ASSEMBLY (Click here)
|
|
| 15. CHECK VEHICLE TYPE |
 |
Check the vehicle type.
Result
Result
|
Proceed to
|
for Double Swing Out Type
|
A
|
except Double Swing Out Type
|
B
|
|
B |
 |
|
|
|
| A |
|
 |
|
| 16. CHECK HARNESS AND CONNECTOR (STOP LIGHT CONTROL RELAY - STOP LIGHT AND BODY GROUND) |
 |
Disconnect the A39 stop light control relay connector.

for LH:
Disconnect the n1 light connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
A39-8 (OUT) - n1-2 (STP)
|
Always
|
Below 1 Ω
|
n1-4 (E) - Body ground
|
n1-2 (STP) - Body ground
|
Always
|
10 kΩ or higher
|
for RH:
Disconnect the Y1 light connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
A39-8 (OUT) - Y1-2 (STP)
|
Always
|
Below 1 Ω
|
Y1-6 (E) - Body ground
|
Y1-2 (STP) - Body ground
|
Always
|
10 kΩ or higher
|
Disconnect the T1 light connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
A39-8 (OUT) - T1-1 (B)
|
Always
|
Below 1 Ω
|
T1-2 (E) - Body ground
|
T1-1 (B) - Body ground
|
Always
|
10 kΩ or higher
|
|
NG |
 |
|
| REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
| OK |
|
 |
|
| REPLACE STOP LIGHT CONTROL RELAY ASSEMBLY (Click here)
|
|
| 17. CHECK HARNESS AND CONNECTOR (STOP LIGHT CONTROL RELAY - STOP LIGHT AND BODY GROUND) |
 |
Disconnect the A39 stop light control relay connector.

for LH:
Disconnect the K4 light connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
A39-8 (OUT) - K4-5 (STP)
|
Always
|
Below 1 Ω
|
K4-3 (E) - Body ground
|
K4-5 (STP) - Body ground
|
Always
|
10 kΩ or higher
|
for RH:
Disconnect the L3 light connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
A39-8 (OUT) - L3-5 (STP)
|
Always
|
Below 1 Ω
|
L3-3 (E) - Body ground
|
L3-5 (STP) - Body ground
|
Always
|
10 kΩ or higher
|
Disconnect the S4 light connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
A39-8 (OUT) - S4-1 (B)
|
Always
|
Below 1 Ω
|
S4-2 (E) - Body ground
|
S4-1 (B) - Body ground
|
Always
|
10 kΩ or higher
|
|
NG |
 |
|
| REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
| OK |
|
 |
|
| REPLACE STOP LIGHT CONTROL RELAY ASSEMBLY (Click here)
|
|
| 18. INSPECT FUSE (STOP FUSE) |
 |
Remove the STOP fuse from the engine room relay block.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
STOP fuse
|
Always
|
Below 1 Ω
|
|
NG |
 |
|
|
|
| OK |
|
 |
|
| 19. INSPECT STOP LIGHT SWITCH |
 |
- Remove the stop light switch (Click here).
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
|
Switch Condition
|
Specified Condition
|
1 - 2
|
Switch pin released
|
Below 1 Ω
|
1 - 2
|
Switch pin pushed in
|
10 kΩ or higher
|
|
NG |
 |
|
|
|
| OK |
|
 |
|
| 20. CHECK HARNESS AND CONNECTOR (STOP LIGHT SWITCH - BODY GROUND) |
 |
Disconnect the A30 stop light switch connector.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
|
Condition
|
Specified Condition
|
A30-2 - Body ground
|
Always
|
11 to 14 V
|
|
NG |
 |
|
| REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
| OK |
|
 |
|
| 21. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - STOP LIGHT SWITCH AND BATTERY) |
 |
Disconnect the A30 stop light switch connector.
Disconnect the 2B ECU connector.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
|
Condition
|
Specified Condition
|
2B-22 (STP) - Body ground
|
Brake pedal depressed
|
11 to 14 V
|
Brake pedal released
|
Below 1 V
|
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
|
Condition
|
Specified Condition
|
2B-22 (STP) - A30-1
|
Always
|
Below 1 Ω
|
A30-1 - Body ground
|
Always
|
10 kΩ or higher
|
|
NG |
 |
|
| REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
| OK |
|
 |
|
|