2011-2013 Land Cruiser · Service Manual Audio / Visual / Telematics

74-40 Short in Speaker Circuit

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

DTC No.
DTC Detection Condition
Trouble Area
74-40
Short is detected in the speaker output circuit.
  1. Harness or connector
  2. Speaker
  3. Stereo component amplifier assembly

WIRING DIAGRAM

E155742E04

INSPECTION PROCEDURE

HINT:
After the inspection is completed, clear the DTCs.


1. CHECK DTC
  1. Disconnect the F3 and F52 amplifier connectors.

  1. Clear the DTCs.

  1. Check if DTC 74-40 is output.

    OK:
    DTC 74-40 is not output.



NG
REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY (Click here)
OK


2. CHECK DTC
  1. Reconnect the F52 amplifier connector.

  1. Clear the DTCs.

  1. Check if DTC 74-40 is output.

    OK:
    DTC 74-40 is not output.



NG
Go to step 6
OK


3. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - SPEAKER)
  1. Disconnect the F3 amplifier connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F3-8 (CTR+) - Body ground
    Always
    10 kΩ or higher
    F3-7 (CTR-) - Body ground
    Always
    10 kΩ or higher
    F3-1 (WFL+) - Body ground
    Always
    10 kΩ or higher
    F3-5 (WFL-) - Body ground
    Always
    10 kΩ or higher
    F3-2 (WFR+) - Body ground
    Always
    10 kΩ or higher
    F3-6 (WFR-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. INSPECT FRONT NO. 1 SPEAKER ASSEMBLY

  1. E144966E35
    Disconnect the I10 and I1 speaker connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    3 Ω

    Text in Illustration 
    *1
    Component without harness connected
    (Front No. 1 Speaker)



NG
REPLACE FRONT NO. 1 SPEAKER ASSEMBLY (Click here)
OK


5. INSPECT FRONT NO. 4 SPEAKER ASSEMBLY

  1. E118525E33
    Disconnect the F6 speaker connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    6 Ω

    Text in Illustration 
    *1
    Component without harness connected
    (Front No. 4 Speaker)



NG
REPLACE FRONT NO. 4 SPEAKER ASSEMBLY (Click here)
OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY (Click here)

6. CHECK HARNESS AND CONNECTOR (STEREO COMPONENT AMPLIFIER - SPEAKER)
  1. Disconnect the F52 amplifier connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F52-8 (FL-) - Body ground
    Always
    10 kΩ or higher
    F52-3 (FL+) - Body ground
    Always
    10 kΩ or higher
    F52-9 (FR-) - Body ground
    Always
    10 kΩ or higher
    F52-10 (FR+) - Body ground
    Always
    10 kΩ or higher
    F52-5 (RR+) - Body ground
    Always
    10 kΩ or higher
    F52-12 (RR-) - Body ground
    Always
    10 kΩ or higher
    F52-4 (RL+) - Body ground
    Always
    10 kΩ or higher
    F52-11 (RL-) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7. INSPECT REAR SPEAKER SET

  1. E144966E35
    Disconnect the J17 and J15 speaker connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    4 Ω

    Text in Illustration 
    *1
    Component without harness connected
    (Rear Speaker Set)



NG
REPLACE REAR SPEAKER SET (Click here)
OK


Go to step 9

8. INSPECT FRONT NO. 2 SPEAKER ASSEMBLY

  1. E144969E35
    Disconnect the F8 and F7 speaker connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    Below 1 Ω
    3 - 4
    Always
    Below 1 Ω
    2 - 4
    Always
    4 Ω

    Text in Illustration 
    *1
    Component without harness connected
    (Front No. 2 Speaker)



NG
REPLACE FRONT NO. 2 SPEAKER ASSEMBLY (Click here)
OK


Go to step 10

9. INSPECT FRONT NO. 3 SPEAKER ASSEMBLY

  1. E197034E01
    Disconnect the F14 and F13 speaker connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    1 - 2
    Always
    4 Ω

    Text in Illustration 
    *1
    Component without harness connected
    (Front No. 3 Speaker)



NG
REPLACE FRONT NO. 3 SPEAKER ASSEMBLY (Click here)
OK


10. CHECK HARNESS AND CONNECTOR (FRONT NO. 2 SPEAKER - FRONT NO. 3 SPEAKER)
  1. Disconnect the F8, F7, F14 and F13 speaker connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for LH:
    Tester Connection
    Condition
    Specified Condition
    F8-2 (TWL+) - F14-1
    Always
    Below 1 Ω
    F8-4 (TWL-) - F14-2
    F8-2 (TWL+) - Body ground
    Always
    10 kΩ or higher
    F8-4 (TWL-) - Body ground
    for RH:
    Tester Connection
    Condition
    Specified Condition
    F7-2 (TWR+) - F13-1
    Always
    Below 1 Ω
    F7-4 (TWR-) - F13-2
    F7-2 (TWR+) - Body ground
    Always
    10 kΩ or higher
    F7-4 (TWR-) - Body ground



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE STEREO COMPONENT AMPLIFIER ASSEMBLY (Click here)


← 63-7D Disc cannot be Played (+ 63-7E, 63-7F) (from Jan 2012)74-40 Short in Speaker Circuit (from Jan 2012) →