2011-2013 Land Cruiser · Service Manual Vehicle Exterior

B2343 Position Initialization Incomplete

Diagnostic trouble codes · Vehicles built from Sep 2011

DESCRIPTION

This DTC is output when the sliding roof drive gear (sliding roof ECU) has not been initialized.
DTC Code
DTC Detection Condition
Trouble Area
B2343
The sliding roof drive gear (sliding roof ECU) has not been initialized
  1. Sliding roof drive gear sub-assembly (Sliding roof ECU)
  2. Map light assembly (Sliding roof switch)
  3. Harness or connector

WIRING DIAGRAM

B181150E01

INSPECTION PROCEDURE


1. INITIALIZE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU)
  1. Check that the sliding roof drive gear can be initialized (Click here).

    OK:
    Sliding roof drive gear can be initialized.



NG
Go to step 3
OK


2. CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check the DTCs (Click here).

    Result 
    Result
    Proceed to
    No DTC is output
    A
    DTC B2343 is output
    B



B
REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU) (Click here)
A

END

3. CHECK HARNESS AND CONNECTOR (SLIDING ROOF DRIVE GEAR - MAP LIGHT)
B181149E01
  1. Disconnect the R5 drive gear connector.

  1. Disconnect the R7 map light connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    R5-10 (UP) - R7-19 (UP)
    Always
    Below 1 Ω
    R5-8 (DWN) - R7-18 (DOWN)
    Always
    Below 1 Ω
    R5-7 (OPN) - R7-8 (OPN)
    Always
    Below 1 Ω
    R5-9 (CLS) - R7-7 (CLS)
    Always
    Below 1 Ω
    R7-17 (GND9) - Body ground
    Always
    Below 1 Ω
    R5-2 (E) - Body ground
    Always
    Below 1 Ω
    R5-10 (UP) or R7-19 (UP) - Body ground
    Always
    10 kΩ or higher
    R5-8 (DWN) or R7-18 (DOWN) - Body ground
    Always
    10 kΩ or higher
    R5-7 (OPN) or R7-8 (OPN) - Body ground
    Always
    10 kΩ or higher
    R5-9 (CLS) or R7-7 (CLS) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. INSPECT MAP LIGHT ASSEMBLY (SLIDING ROOF SWITCH)
B237546E01
  1. Remove the map light (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    19 (UP) - 17 (GND9)
    UP switch is pressed
    Below 1 Ω
    19 (UP) - 17 (GND9)
    UP switch is not pressed
    10 kΩ or higher
    18 (DOWN) - 17 (GND9)
    DOWN switch is pressed
    Below 1 Ω
    18 (DOWN) - 17 (GND9)
    DOWN switch is not pressed
    10 kΩ or higher
    8 (OPN) - 17 (GND9)
    OPEN switch is pressed
    Below 1 Ω
    8 (OPN) - 17 (GND9)
    OPEN switch is not pressed
    10 kΩ or higher
    7 (CLS) - 17 (GND9)
    CLOSE switch is pressed
    Below 1 Ω
    7 (CLS) - 17 (GND9)
    CLOSE switch is not pressed
    10 kΩ or higher



NG
REPLACE MAP LIGHT ASSEMBLY (SLIDING ROOF SWITCH) (Click here)
OK

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU) (Click here)


← B2342 Switch Failure (from Sep 2011)Sliding Roof Control Switch Circuit (from Sep 2011) →