2011-2013 Land Cruiser · Service Manual Vehicle Exterior

B2342 Switch Failure

Diagnostic trouble codes · Vehicles built from Sep 2011

DESCRIPTION

This DTC is stored when the sliding roof drive gear (sliding roof ECU) detects that the SLIDE OPEN or TILT UP switch in the map light is stuck for 30 seconds or more.
DTC Code
DTC Detection Condition
Trouble Area
B2342
Sliding roof drive gear (sliding roof ECU) detects sliding roof switch in map light is stuck for 30 seconds or more
  1. Sliding roof drive gear sub-assembly (Sliding roof ECU)
  2. Map light assembly (Sliding roof switch)
  3. Harness or connector

WIRING DIAGRAM

B181150E01

INSPECTION PROCEDURE


1. CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check the DTCs (Click here).

    Result 
    Result
    Proceed to
    DTC B2342 is output
    A
    No DTC is output
    B



B
USE SIMULATION METHOD TO CHECK (Click here)
A


2. READ VALUE USING INTELLIGENT TESTER (SWITCH STATUS)
  1. Use the Data List to check if the sliding roof switch is functioning properly (Click here).

    Sliding Roof 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Down Switch Failure(Current)
    Down switch failure signal (Current)/Fail or Not Fail
    Fail: Sliding roof tilt down signal failure (Current)
    Not Fail: Sliding roof tilt down signal not fail (Current)
    -
    Up Switch Failure(Current)
    Up switch failure signal (Current)/Fail or Not Fail
    Fail: Sliding roof tilt up signal failure (Current)
    Not Fail: Sliding roof tilt up signal not fail (Current)
    -
    Close Switch Failure(Current)
    Close switch failure signal (Current)/Fail or Not Fail
    Fail: Sliding roof close signal failure (Current)
    Not Fail: Sliding roof close signal not fail (Current)
    -
    Open Switch Failure(Current)
    Open switch failure signal (Current)/Fail or Not Fail
    Fail: Sliding roof open signal failure (Current)
    Not Fail: Sliding roof open signal not fail (Current)
    -
    Down Switch Failure(Past)
    Down switch failure signal (Past)/Fail or Not Fail
    Fail: Sliding roof tilt down signal failure (Past)
    Not Fail: Sliding roof tilt down signal not fail (Past)
    -
    Up Switch Failure(Past)
    Up switch failure signal (Past)/Fail or Not Fail
    Fail: Sliding roof tilt up signal failure (Past)
    Not Fail: Sliding roof tilt up signal not fail (Past)
    -
    Close Switch Failure(Past)
    Close switch failure signal (Past)/Fail or Not Fail
    Fail: Sliding roof close signal failure (Past)
    Not Fail: Sliding roof close signal not fail (Past)
    -
    Open Switch Failure(Past)
    Open switch failure signal (Past)/Fail or Not Fail
    Fail: Sliding roof open signal failure (Past)
    Not Fail: Sliding roof open signal not fail (Past)
    -

OK:
"Not Fail" appears on screen.



NG
Go to step 3
OK

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU) (Click here)

3. INSPECT MAP LIGHT ASSEMBLY (SLIDING ROOF SWITCH)
B237546E01
  1. Remove the map light (Click here).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    19 (UP) - 17 (GND9)
    UP switch is pressed
    Below 1 Ω
    19 (UP) - 17 (GND9)
    UP switch is not pressed
    10 kΩ or higher
    18 (DOWN) - 17 (GND9)
    DOWN switch is pressed
    Below 1 Ω
    18 (DOWN) - 17 (GND9)
    DOWN switch is not pressed
    10 kΩ or higher
    8 (OPN) - 17 (GND9)
    OPEN switch is pressed
    Below 1 Ω
    8 (OPN) - 17 (GND9)
    OPEN switch is not pressed
    10 kΩ or higher
    7 (CLS) - 17 (GND9)
    CLOSE switch is pressed
    Below 1 Ω
    7 (CLS) - 17 (GND9)
    CLOSE switch is not pressed
    10 kΩ or higher



NG
REPLACE MAP LIGHT ASSEMBLY (SLIDING ROOF SWITCH) (Click here)
OK


4. CHECK HARNESS AND CONNECTOR (SLIDING ROOF DRIVE GEAR - MAP LIGHT)
B181149E01
  1. Disconnect the R5 drive gear connector.

  1. Disconnect the R7 map light connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    R5-10 (UP) - R7-19 (UP)
    Always
    Below 1 Ω
    R5-8 (DWN) - R7-18 (DOWN)
    Always
    Below 1 Ω
    R5-7 (OPN) - R7-8 (OPN)
    Always
    Below 1 Ω
    R5-9 (CLS) - R7-7 (CLS)
    Always
    Below 1 Ω
    R7-17 (GND9) - Body ground
    Always
    Below 1 Ω
    R5-2 (E) - Body ground
    Always
    Below 1 Ω
    R5-10 (UP) or R7-19 (UP) - Body ground
    Always
    10 kΩ or higher
    R5-8 (DWN) or R7-18 (DOWN) - Body ground
    Always
    10 kΩ or higher
    R5-7 (OPN) or R7-8 (OPN) - Body ground
    Always
    10 kΩ or higher
    R5-9 (CLS) or R7-7 (CLS) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE SLIDING ROOF DRIVE GEAR SUB-ASSEMBLY (SLIDING ROOF ECU) (Click here)


← B2341 Sensor (Motor) Failure (+ B2344) (from Sep 2011)B2343 Position Initialization Incomplete (from Sep 2011) →