2011-2013 Land Cruiser · Service Manual Audio / Visual / Telematics

C1AEC Front Sensor Communication Malfunction

Diagnostic trouble codes · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

This DTC is stored when there is an open or short circuit in the communication line between the front sensors and the ECU, or when there is a malfunction in a front sensor.
DTC Code
DTC Detection Condition
Trouble Area
C1AEC
An open or short circuit in the communication line between the front sensors and ECU or a malfunction in a front sensor during initialization mode after the engine switch is turned on (IG).
  1. No. 1 ultrasonic sensor (front side)
  2. Harness or connector
  3. Parking assist ECU*1
  4. Clearance warning ECU assembly*2
  1. *1: w/ Side Monitor System
  2. *2: w/o Side Monitor System

WIRING DIAGRAM

E246937E01

INSPECTION PROCEDURE


1. CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    Result 
    Result
    Proceed to
    DTC C1AEC is output (w/ Side Monitor System)
    A
    DTC C1AEC is output (w/o Side Monitor System)
    B
    DTC C1AEC is not output
    C



B
Go to step 10

C
USE SIMULATION METHOD TO CHECK (Click here)
A


2. CHECK HARNESS AND CONNECTOR (NO. 1 ULTRASONIC SENSOR [FL SENSOR] - PARKING ASSIST ECU)
  1. Disconnect the B8 No. 1 ultrasonic sensor (FL sensor) connector.

  1. Disconnect the F76 parking assist ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B8-1 (BI) - F76-5 (CSB1)
    Always
    Below 1 Ω
    B8-3 (SI) - F76-23 (LIN1)
    Always
    Below 1 Ω
    B8-5 (EI) - F76-6 (CSG1)
    Always
    Below 1 Ω
    B8-1 (BI) - Body ground
    Always
    10 kΩ or higher
    B8-3 (SI) - Body ground
    Always
    10 kΩ or higher
    B8-5 (EI) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. CHECK HARNESS AND CONNECTOR (NO. 1 ULTRASONIC SENSOR [FL SENSOR] - NO. 1 ULTRASONIC SENSOR [FR SENSOR])
  1. Disconnect the B8 No. 1 ultrasonic sensor (FL sensor) connector.

  1. Disconnect the B7 No. 1 ultrasonic sensor (FR sensor) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B8-2 (BO) - B7-1 (BI)
    Always
    Below 1 Ω
    B8-4 (SO) - B7-3 (SI)
    Always
    Below 1 Ω
    B8-6 (EO) - B7-5 (EI)
    Always
    Below 1 Ω
    B8-2 (BO) - Body ground
    Always
    10 kΩ or higher
    B8-4 (SO) - Body ground
    Always
    10 kΩ or higher
    B8-6 (EO) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK PARKING ASSIST ECU

  1. E140580E15
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    F76-5 (CSB1) - Body ground
    Engine switch on (IG)
    7.2 to 8.8 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F76-6 (CSG1) - Body ground
    Always
    Below 1 Ω

Text in Illustration 
*a
Component with harness connected
(Parking Assist ECU)


NG
REPLACE PARKING ASSIST ECU (Click here)
OK


5. CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC C1AEC is not output.



NG
Go to step 6
OK

USE SIMULATION METHOD TO CHECK (Click here)

6. REPLACE NO. 1 ULTRASONIC SENSOR (FL SENSOR)
  1. Replace the No. 1 ultrasonic sensor (FL sensor) with a normally functioning one (Click here).


NEXT


7. CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC C1AEC is not output.



NG
Go to step 8
OK

END (NO. 1 ULTRASONIC SENSOR [FL SENSOR] IS DEFECTIVE)

8. REPLACE NO. 1 ULTRASONIC SENSOR (FR SENSOR)
  1. Replace the No. 1 ultrasonic sensor (FR sensor) with a normally functioning one (Click here)


NEXT


9. CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC C1AEC is not output.



NG
REPLACE PARKING ASSIST ECU (Click here)
OK

END (NO. 1 ULTRASONIC SENSOR [FR SENSOR] IS DEFECTIVE)

10. CHECK HARNESS AND CONNECTOR (NO. 1 ULTRASONIC SENSOR [FL SENSOR] - CLEARANCE WARNING ECU ASSEMBLY)
  1. Disconnect the B8 No. 1 ultrasonic sensor [FL sensor] connector.

  1. Disconnect the F12 clearance warning ECU assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B8-1 (BI) - F12-21 (CSB1)
    Always
    Below 1 Ω
    B8-3 (SI) - F12-9 (LIN1)
    Always
    Below 1 Ω
    B8-5 (EI) - F12-19 (CSG1)
    Always
    Below 1 Ω
    B8-1 (BI) - Body ground
    Always
    10 kΩ or higher
    B8-3 (SI) - Body ground
    Always
    10 kΩ or higher
    B8-5 (EI) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


11. CHECK HARNESS AND CONNECTOR (NO. 1 ULTRASONIC SENSOR [FL SENSOR] - NO. 1 ULTRASONIC SENSOR [FR SENSOR])
  1. Disconnect the B8 No. 1 ultrasonic sensor (FL sensor) connector.

  1. Disconnect the B7 No. 1 ultrasonic sensor (FR sensor) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    B8-2 (BO) - B7-1 (BI)
    Always
    Below 1 Ω
    B8-4 (SO) - B7-3 (SI)
    Always
    Below 1 Ω
    B8-6 (EO) - B7-5 (EI)
    Always
    Below 1 Ω
    B8-2 (BO) - Body ground
    Always
    10 kΩ or higher
    B8-4 (SO) - Body ground
    Always
    10 kΩ or higher
    B8-6 (EO) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


12. CHECK CLEARANCE WARNING ECU ASSEMBLY

  1. B179112E14
    Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    F12-21 (CSB1) - Body ground
    Engine switch on (IG)
    7.2 to 8.8 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    F12-19 (CSG1) - Body ground
    Always
    Below 1 Ω

Text in Illustration 
*a
Component with harness connected
(Clearance Warning ECU Assembly)


NG
REPLACE CLEARANCE WARNING ECU ASSEMBLY (Click here)
OK


13. CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC C1AEC is not output.



NG
Go to step 4
OK

USE SIMULATION METHOD TO CHECK (Click here)

14. REPLACE NO. 1 ULTRASONIC SENSOR (FL SENSOR)
  1. Replace the No. 1 ultrasonic sensor (FL sensor) with a normally functioning one (Click here).


NEXT


15. CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC C1AEC is not output.



NG
Go to step 16
OK

END (NO. 1 ULTRASONIC SENSOR [FL SENSOR] IS DEFECTIVE)

16. REPLACE NO. 1 ULTRASONIC SENSOR (FR SENSOR)
  1. Replace the No. 1 ultrasonic sensor (FR sensor) with a normally functioning one (Click here).


NEXT


17. CHECK FOR DTC
  1. Clear the DTCs (Click here).

  1. Check for DTCs (Click here).

    OK:
    DTC C1AEC is not output.



NG
REPLACE CLEARANCE WARNING ECU ASSEMBLY (Click here)
OK

END (NO. 1 ULTRASONIC SENSOR [FR SENSOR] IS DEFECTIVE)


← C1AEC Front Sensor Communication Malfunction (Sep 2011 – Dec 2011)C1AED Rear Sensor Communication Malfunction (Sep 2011 – Dec 2011) →