2011-2013 Land Cruiser · Service Manual Power Source / Network

Short to B+ in CAN Bus Line

Circuit diagnosis · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

There may be a short circuit between the CAN bus lines and +B when the resistance between terminals 6 (CANH) and 16 (BAT) or terminals 14 (CANL) and 16 (BAT) of the DLC3 is below 6 kΩ.
Symptom
Trouble Area
The resistance between terminals 6 (CANH) and 16 (BAT) or terminals 14 (CANL) and 16 (BAT) of the DLC3 is below 6 kΩ.
  1. Short between CAN bus lines and +B
  2. ECM
  3. Center airbag sensor assembly*1
  4. Headlight swivel ECU assembly*2
  5. Multi-media module receiver assembly*3
  6. Air conditioning amplifier assembly
  7. Network gateway ECU
  8. Main body ECU (cowl side junction block LH)
  9. Combination meter assembly
  10. No. 1 junction connector
  11. No. 2 junction connector
  12. No. 3 junction connector
  1. *1: w/ Airbag System
  2. *2: w/ Dynamic Headlight Auto Leveling
  3. *3: w/ Navigation System

WIRING DIAGRAM

C260052E01
C260053E01

INSPECTION PROCEDURE

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).


NEXT


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    For vehicles with an SRS system:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


3. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (DLC3 CAN BRANCH WIRE)

  1. C253362E07
    Disconnect the E75 No. 3 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E22-6 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E22-14 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)
OK


4. CONNECT CONNECTOR
  1. Reconnect the E75 No. 3 junction connector.


NEXT


5. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR SIDE)

  1. C253362E07
    Disconnect the E72 No. 1 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E22-6 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E22-14 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of DLC3



NG
Go to step 12
OK


6. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - CENTER AIRBAG SENSOR ASSEMBLY)

NOTICE:
For vehicles without an airbag system, go to "Check for Short to B+ in CAN Bus Wire (No. 1 Junction Connector - Main Body ECU)".

  1. C259545E02
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E72-4 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E72-15 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 9
OK


7. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - MAIN BODY ECU)

  1. C259545E01
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E72-3 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E72-14 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 10
OK


8. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - ECM)

  1. C259545E03
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E72-2 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E72-13 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 11
OK

REPLACE NO. 1 JUNCTION CONNECTOR

9. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (CENTER AIRBAG SENSOR ASSEMBLY)

  1. C259545E02
    Disconnect the E47 center airbag sensor assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E72-4 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E72-15 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CENTER AIRBAG SENSOR ASSEMBLY (CANH, CANL)
OK

REPLACE CENTER AIRBAG SENSOR ASSEMBLY (Click here)

10. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (MAIN BODY ECU)

  1. C259545E01
    Disconnect the E3 main body ECU (cowl side junction block LH) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E72-3 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E72-14 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MAIN BODY ECU (CANH, CANL)
OK

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)

11. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (ECM)

  1. C259545E03
    Disconnect the A52 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E72-2 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E72-13 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    *b
    Front view of DLC3
    Result 
    Result
    Proceed to
    OK (for 1GR-FE)
    A
    OK (for 1UR-FE)
    B
    OK (for 1VD-FTV)
    C
    NG
    D



B
REPLACE ECM (Click here)

C
REPLACE ECM (Click here)

D
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)
A

REPLACE ECM (Click here)

12. CONNECT CONNECTOR
  1. Reconnect the E72 No. 1 junction connector.


NEXT


13. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)

  1. C259545E53
    Disconnect the E69 No. 2 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E69-4 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E69-15 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)
OK


14. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR SIDE)

  1. C253362E07
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E22-6 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E22-14 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of DLC3



NG
Go to step 23
OK


15. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - MULTI-MEDIA MODULE RECEIVER ASSEMBLY)

NOTICE:
For vehicles without an navigation system, go to "Check for Short to B+ in CAN Bus Wire (No. 2 Junction Connector - Air Conditioning Amplifier)".

  1. C259545E05
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E69-2 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E69-13 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 19
OK


16. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER ASSEMBLY)

  1. C259545E07
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E69-5 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E69-16 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 20
OK


17. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - HEADLIGHT SWIVEL ECU ASSEMBLY)

NOTICE:
For vehicles without an dynamic headlight auto leveling, go to "Check for Short to B+ in CAN Bus Wire (No. 2 Junction Connector - Network Gateway ECU)".

  1. C259545E54
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E69-7 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E69-18 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 21
OK


18. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - NETWORK GATEWAY ECU)

  1. C259545E06
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E69-3 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E69-14 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 22
OK

REPLACE NO. 2 JUNCTION CONNECTOR

19. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (MULTI-MEDIA MODULE RECEIVER ASSEMBLY)

  1. C259545E05
    Disconnect the F77 multi-media module receiver assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E69-2 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E69-13 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MULTI-MEDIA MODULE RECEIVER ASSEMBLY (CANH, CANL)
OK

REPLACE MULTI-MEDIA MODULE RECEIVER ASSEMBLY (Click here)

20. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (AIR CONDITIONING AMPLIFIER ASSEMBLY)

  1. C259545E07
    Disconnect the E35*1 or E81*2 air conditioning amplifier connector.
    1. *1: w/ Rear Air Conditioning System
    2. *2: w/o Rear Air Conditioning System

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E69-5 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E69-16 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO AIR CONDITIONING AMPLIFIER ASSEMBLY (CANH, CANL)
OK

REPLACE AIR CONDITIONING AMPLIFIER ASSEMBLY (Click here)

21. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (HEADLIGHT SWIVEL ECU ASSEMBLY)

  1. C259545E54
    Disconnect the E101 headlight swivel ECU assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E69-7 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E69-18 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO HEADLIGHT SWIVEL ECU ASSEMBLY (MPX1, MPX2)
OK

REPLACE HEADLIGHT SWIVEL ECU ASSEMBLY (Click here)

22. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NETWORK GATEWAY ECU)

  1. C259545E06
    Disconnect the E31 network gateway ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E69-3 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E69-14 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO NETWORK GATEWAY ECU (CANH, CANL)
OK

REPLACE NETWORK GATEWAY ECU (Click here)

23. CONNECT CONNECTOR
  1. Reconnect the E69 No. 2 junction connector.


NEXT


24. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)

  1. C259545E08
    Disconnect the E75 No. 3 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E75-1 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E75-12 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
OK


25. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)

  1. C259545E10
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E75-3 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E75-14 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 26
OK

REPLACE NO. 3 JUNCTION CONNECTOR

26. CHECK FOR SHORT TO B+ IN CAN BUS WIRE (COMBINATION METER ASSEMBLY)

  1. C259545E10
    Disconnect the E7 combination meter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E75-3 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E75-14 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 3 Junction Connector)
    *b
    Front view of DLC3
    Result 
    Result
    Proceed to
    OK (w/ Multi-information Display)
    A
    OK (w/o Multi-information Display)
    B
    NG
    C



B
REPLACE COMBINATION METER ASSEMBLY (Click here)

C
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ASSEMBLY (CANH, CANL)
A

REPLACE COMBINATION METER ASSEMBLY (Click here)


← Short to B+ in CAN Bus Line (Sep 2011 – Dec 2011)Short to GND in CAN Bus Line (Sep 2011 – Dec 2011) →