Open in CAN Main Wire
Circuit diagnosis · Vehicles built from Jan 2012
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
DESCRIPTION
There may be an open circuit in the CAN main wire and/or DLC3 CAN branch wire when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 69 Ω or higher.| Symptom |
Trouble Area |
| The resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is 69 Ω or higher. |
|
- *: w/o Network Gateway ECU
WIRING DIAGRAM




INSPECTION PROCEDURE
- HINT:
- Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
| 1. PRECAUTION |
- NOTICE:
- After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
| NEXT | |
| 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.
- CAUTION:
- For vehicles with an SRS system:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
- NOTICE:
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).
| NEXT | |
| 3. CHECK FOR OPEN IN CAN BUS WIRE (NO. 3 JUNCTION CONNECTOR - DLC3) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E22-6 (CANH) - E22-14 (CANL)
Ignition switch off
108 to 132 Ω
Text in Illustration *a
Front view of DLC3
- NOTICE:
- When the measured value is 133 Ω or higher and a CAN communication system diagnostic trouble code is output, there may be a fault besides disconnection of the DLC3 branch wire. For that reason, troubleshooting should be performed again from "How to Proceed with Troubleshooting" (Click here) after repairing the trouble area.
|
|
||||
| OK | |
| 4. CHECK FOR OPEN IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - ECM) |
Disconnect the E69 No. 2 junction connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E69-1 (CANH) - E69-12 (CANL)
Ignition switch off
108 to 132 Ω
Text in Illustration *a
Rear view of wire harness connector
(to No. 2 Junction Connector)
|
|
||||
| OK | |
| 5. CHECK FOR OPEN IN CAN BUS WIRE (NO. 2 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E69-4 (CANH) - E69-15 (CANL)
Ignition switch off
108 to 132 Ω
Text in Illustration *a
Rear view of wire harness connector
(to No. 2 Junction Connector)
|
|
||||
| OK | ||
| ||
| 6. CONNECT CONNECTOR |
Reconnect the E69 No. 2 junction connector.
| NEXT | |
| 7. CHECK FOR OPEN IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - ECM) |
Disconnect the E72 No. 1 junction connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E72-2 (CANH) - E72-13 (CANL)
Ignition switch off
108 to 132 Ω
Text in Illustration *a
Rear view of wire harness connector
(to No. 1 Junction Connector)
|
|
||||
| OK | |
| 8. CHECK FOR OPEN IN CAN BUS WIRE (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E72-1 (CANH) - E72-12 (CANL)
Ignition switch off
108 to 132 Ω
Text in Illustration *a
Rear view of wire harness connector
(to No. 1 Junction Connector)
|
|
||||
| OK | ||
| ||
| 9. CONNECT CONNECTOR |
Reconnect the E72 No. 1 junction connector.
| NEXT | |
| 10. CHECK FOR OPEN IN CAN BUS MAIN WIRE (ECM - NO. 1 JUNCTION CONNECTOR) |
Disconnect the A38 ECM connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
except 1VD-FTV Tester Connection
Switch Condition
Specified Condition
A38-10 (CANH) - A38-11 (CANL)
Ignition switch off
108 to 132 Ω
for 1VD-FTV Tester Connection
Switch Condition
Specified Condition
A38-41 (CANH) - A38-49 (CANL)
Ignition switch off
108 to 132 Ω
Text in Illustration *A
except 1VD-FTV
*B
for 1VD-FTV
*a
Front view of wire harness connector
(to ECM)
Result Result
Proceed to
OK (for 1GR-FE)
A
OK (for 1UR-FE)
B
OK (for 3UR-FE)
C
OK (for 1VD-FTV)
D
NG
E
|
|
||||
|
|
||||
|
|
||||
|
|
||||
| A | ||
| ||
| 11. CONNECT CONNECTOR |
Reconnect the E69 No. 2 junction connector.
| NEXT | |
| 12. SYSTEM CHECK |
Check the vehicle specifications.
Result Result
Proceed to
w/ Network Gateway ECU
A
w/o Network Gateway ECU
B
|
|
||||
| A | |
| 13. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 3 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY) |
Disconnect the E75 No. 3 junction connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E75-3 (CANH) - E75-14 (CANL)
Ignition switch off
108 to 132 Ω
Text in Illustration *a
Rear view of wire harness connector
(to No. 3 Junction Connector)
|
|
||||
| OK | |
| 14. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 3 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E75-1 (CANH) - E75-12 (CANL)
Ignition switch off
108 to 132 Ω
Text in Illustration *a
Rear view of wire harness connector
(to No. 3 Junction Connector)
|
|
||||
| OK | ||
| ||
| 15. CONNECT CONNECTOR |
Reconnect the E75 No. 3 junction connector.
| NEXT | |
| 16. CHECK FOR OPEN IN CAN BUS MAIN WIRE (COMBINATION METER - NO. 3 JUNCTION CONNECTOR) |
Disconnect the E7 combination meter assembly connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E7-25 (CANH) - E7-26 (CANL)
Ignition switch off
108 to 132 Ω
Text in Illustration *a
Front view of wire harness connector
(to Combination Meter Assembly)
Result Result
Proceed to
OK (w/ Multi-information Display)
A
OK (w/o Multi-information Display)
B
NG
C
|
|
||||
|
|
||||
| A | ||
| ||
| 17. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 6 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY) |
Disconnect the F73 No. 6 junction connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
F73-6 (CANH) - F73-17 (CANL)
Ignition switch off
108 to 132 Ω
Text in Illustration *a
Rear view of wire harness connector
(to No. 6 Junction Connector)
|
|
||||
| OK | |
| 18. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 6 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
F73-7 (CANH) - F73-18 (CANL)
Ignition switch off
108 to 132 Ω
Text in Illustration *a
Rear view of wire harness connector
(to No. 6 Junction Connector)
|
|
||||
| OK | ||
| ||
| 19. CONNECT CONNECTOR |
Reconnect the F73 No. 6 junction connector.
| NEXT | |
| 20. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 3 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY) |
Disconnect the E75 No. 3 junction connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E75-3 (CANH) - E75-14 (CANL)
Ignition switch off
108 to 132 Ω
Text in Illustration *a
Rear view of wire harness connector
(to No. 3 Junction Connector)
|
|
||||
| OK | |
| 21. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 3 JUNCTION CONNECTOR - NO. 6 JUNCTION CONNECTOR) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E75-1 (CANH) - E75-12 (CANL)
Ignition switch off
108 to 132 Ω
Text in Illustration *a
Rear view of wire harness connector
(to No. 3 Junction Connector)
|
|
||||
| OK | ||
| ||
| 22. CONNECT CONNECTOR |
Reconnect the E75 No. 3 junction connector.
| NEXT | |
| 23. CHECK FOR OPEN IN CAN BUS MAIN WIRE (COMBINATION METER ASSEMBLY - NO. 3 JUNCTION CONNECTOR) |
Disconnect the E7 combination meter assembly connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E7-25 (CANH) - E7-26 (CANL)
Ignition switch off
108 to 132 Ω
Text in Illustration *a
Front view of wire harness connector
(to Combination Meter Assembly)
Result Result
Proceed to
OK (w/ Multi-information Display)
A
OK (w/o Multi-information Display)
B
NG
C
|
|
||||
|
|
||||
| A | ||
| ||
