2011-2013 Land Cruiser · Service Manual Power Source / Network

Short in CAN Bus Lines

Circuit diagnosis · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

There may be a short circuit between the CAN bus lines when the resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 54 Ω.
Symptom
Trouble Area
Resistance between terminals 6 (CANH) and 14 (CANL) of the DLC3 is below 54 Ω.
  1. Short between CAN bus lines
  2. ECM
  3. Center airbag sensor assembly*1
  4. Display and navigation module display*2
  5. Air conditioning amplifier assembly
  6. Network gateway ECU*3
  7. Main body ECU (cowl side junction block LH)
  8. Combination meter assembly
  9. 4WD control ECU*4
  10. Clearance warning ECU*4
  11. Master cylinder solenoid (skid control ECU)*4
  12. No. 1 junction connector
  13. No. 2 junction connector
  14. No. 3 junction connector
  15. No. 6 junction connector*4
  1. *1: w/ Airbag System
  2. *2: w/ Navigation System
  3. *3: w/ Network Gateway ECU
  4. *4: w/o Network Gateway ECU

WIRING DIAGRAM

E207342E03
E207343E02
C246723E01
E207345E02

INSPECTION PROCEDURE

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.

    CAUTION:
    For vehicles with an SRS system:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


2. CHECK FOR SHORT IN CAN BUS WIRES (DLC3 BRANCH WIRE)

  1. E194588E09
    Disconnect the E75 No. 3 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E22-6 (CANH) - E22-14 (CANL)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *1
    DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DLC3 (CANH, CANL)
OK


3. CONNECT CONNECTOR
  1. Reconnect the E75 No. 3 junction connector connector.


NEXT


4. SYSTEM CHECK
  1. Check the vehicle specifications.

    Result 
    Result
    Proceed to
    w/ Network Gateway ECU
    A
    w/o Network Gateway ECU
    B



B
Go to step 25
A


5. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR SIDE)

  1. E194588E09
    Disconnect the E72 No. 1 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E22-6 (CANH) - E22-14 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *1
    DLC3



NG
Go to step 10
OK


6. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - CENTER AIRBAG SENSOR)

  1. E186808E31
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E72-4 (CANH) - E72-15 (CANL)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 1 Junction Connector)



NG
Go to step 8
OK


7. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - ECM)

  1. E186808E33
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E72-2 (CANH) - E72-13 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 1 Junction Connector)



NG
Go to step 9
OK

REPAIR OR REPLACE NO. 1 JUNCTION CONNECTOR

8. CHECK FOR SHORT IN CAN BUS WIRES (CENTER AIRBAG SENSOR)

  1. E186808E31
    Disconnect the E47 center airbag sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E72-4 (CANH) - E72-15 (CANL)
    Ignition switch off
    1 MΩ or higher

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 1 Junction Connector)



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CENTER AIRBAG SENSOR (CANH, CANL)
OK

REPLACE CENTER AIRBAG SENSOR (Click here)

9. CHECK FOR SHORT IN CAN BUS WIRES (ECM)

  1. E186808E33
    Disconnect the A38 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E72-2 (CANH) - E72-13 (CANL)
    Ignition switch off
    1 MΩ or higher

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    Result 
    Result
    Proceed to
    OK (for 2UZ-FE)
    A
    OK (for 1GR-FE)
    B
    OK (for 1VD-FTV)
    C
    OK (for 3UR-FE)
    D
    NG
    E



B
REPLACE ECM (Click here)

C
REPLACE ECM (Click here)

D
REPLACE ECM (Click here)

E
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)
A

REPLACE ECM (Click here)

10. CONNECT CONNECTOR
  1. Reconnect the E72 No. 1 junction connector connector.


NEXT


11. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)

  1. E186808E34
    Disconnect the E69 No. 2 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E69-1 (CANH) - E69-12 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 2 Junction Connector)



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 2 JUNCTION CONNECTOR - NO. 1 JUNCTION CONNECTOR)
OK


12. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR SIDE)

  1. E194588E09
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E22-6 (CANH) - E22-14 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *1
    DLC3



NG
Go to step 19
OK


13. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - DISPLAY AND NAVIGATION MODULE DISPLAY)

NOTICE:
For vehicles without the navigation system, go to "Check for Short in CAN Bus Wires (No. 2 Junction Connector - Air Conditioning Amplifier)".

  1. E186808E35
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E69-2 (CANH) - E69-13 (CANL)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 2 Junction Connector)



NG
Go to step 16
OK


14. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER)

  1. E186808E36
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E69-5 (CANH) - E69-16 (CANL)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 2 Junction Connector)



NG
Go to step 17
OK


15. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - NETWORK GATEWAY ECU)

  1. E186808E37
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E69-3 (CANH) - E69-14 (CANL)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 2 Junction Connector)



NG
Go to step 18
OK

REPAIR OR REPLACE NO. 2 JUNCTION CONNECTOR

16. CHECK FOR SHORT IN CAN BUS WIRES (DISPLAY AND NAVIGATION MODULE DISPLAY)

  1. E186808E35
    Disconnect the F64 display and navigation module display connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E69-2 (CANH) - E69-13 (CANL)
    Ignition switch off
    1 MΩ or higher

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 2 Junction Connector)



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DISPLAY AND NAVIGATION MODULE DISPLAY (CANH, CANL)
OK

REPLACE DISPLAY AND NAVIGATION MODULE DISPLAY (Click here)

17. CHECK FOR SHORT IN CAN BUS WIRES (AIR CONDITIONING AMPLIFIER)

  1. E186808E36
    Disconnect the E35*1 or E81*2 air conditioning amplifier connector.*1: w/ Rear Air Conditioning System*2: w/o Rear Air Conditioning System

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E69-5 (CANH) - E69-16 (CANL)
    Ignition switch off
    1 MΩ or higher

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 2 Junction Connector)



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO AIR CONDITIONING AMPLIFIER (CANH, CANL)
OK

REPLACE AIR CONDITIONING AMPLIFIER (Click here)

18. CHECK FOR SHORT IN CAN BUS WIRES (NETWORK GATEWAY ECU)

  1. E186808E37
    Disconnect the E31 network gateway ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E69-3 (CANH) - E69-14 (CANL)
    Ignition switch off
    1 MΩ or higher

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 2 Junction Connector)



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO NETWORK GATEWAY ECU (CA1H, CA1L)
OK

REPLACE NETWORK GATEWAY ECU (Click here)

19. CONNECT CONNECTOR
  1. Reconnect the E69 No. 2 junction connector connector.


NEXT


20. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)

  1. E186808E38
    Disconnect the E75 No. 3 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E75-1 (CANH) - E75-12 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 3 Junction Connector)



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 2 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)
OK


21. CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - MAIN BODY ECU)

  1. E186808E39
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E75-4 (CANH) - E75-15 (CANL)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 3 Junction Connector)



NG
Go to step 23
OK


22. CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - COMBINATION METER)

  1. E186808E40
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E75-3 (CANH) - E75-14 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 3 Junction Connector)



NG
Go to step 24
OK

REPAIR OR REPLACE NO. 3 JUNCTION CONNECTOR

23. CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU)

  1. E186808E39
    Disconnect the E3 main body ECU (cowl side junction block LH) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E75-4 (CANH) - E75-15 (CANL)
    Ignition switch off
    1 MΩ or higher

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 3 Junction Connector)



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH) (CANH, CANL)
OK

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)

24. CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER)

  1. E186808E40
    Disconnect the E7 combination meter connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E75-3 (CANH) - E75-14 (CANL)
    Ignition switch off
    1 MΩ or higher

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 3 Junction Connector)

Result 
Result
Proceed to
OK (w/ Multi-information Display)
A
OK (w/o Multi-information Display)
B
NG
C


B
REPLACE COMBINATION METER (Click here)

C
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER (CANH, CANL)
A

REPLACE COMBINATION METER (Click here)

25. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR SIDE)

  1. E194588E09
    Disconnect the E72 No. 1 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E22-6 (CANH) - E22-14 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *1
    DLC3



NG
Go to step 32
OK


26. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - CENTER AIRBAG SENSOR)

NOTICE:
For vehicles without the airbag system, go to "Check for Short in CAN Bus Wires (No. 2 Junction Connector - 4WD Control ECU)".

  1. E186808E31
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E72-4 (CANH) - E72-15 (CANL)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 1 Junction Connector)



NG
Go to step 29
OK


27. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - 4WD CONTROL ECU)

  1. E186808E66
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E72-5 (CANH) - E72-16 (CANL)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 1 Junction Connector)



NG
Go to step 30
OK


28. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - ECM)

  1. E186808E33
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E72-2 (CANH) - E72-13 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 1 Junction Connector)



NG
Go to step 31
OK

REPAIR OR REPLACE NO. 1 JUNCTION CONNECTOR

29. CHECK FOR SHORT IN CAN BUS WIRES (CENTER AIRBAG SENSOR)

  1. E186808E31
    Disconnect the E47 center airbag sensor connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E72-4 (CANH) - E72-15 (CANL)
    Ignition switch off
    1 MΩ or higher

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 1 Junction Connector)



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CENTER AIRBAG SENSOR (CANH, CANL)
OK

REPLACE CENTER AIRBAG SENSOR (Click here)

30. CHECK FOR SHORT IN CAN BUS WIRES (4WD CONTROL ECU)

  1. E186808E67
    Disconnect the A27 4WD control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E72-5 (CANH) - E72-16 (CANL)
    Ignition switch off
    1 MΩ or higher

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 1 Junction Connector)



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO 4WD CONTROL ECU (CAN+, CAN-)
OK

REPLACE 4WD CONTROL ECU (Click here)

31. CHECK FOR SHORT IN CAN BUS WIRES (ECM)

  1. E186808E33
    Disconnect the A38 ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E72-2 (CANH) - E72-13 (CANL)
    Ignition switch off
    1 MΩ or higher

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 1 Junction Connector)
    Result 
    Result
    Proceed to
    OK (for 2UZ-FE)
    A
    OK (for 1GR-FE)
    B
    OK (for 1VD-FTV)
    C
    NG
    D



B
REPLACE ECM (Click here)

C
REPLACE ECM (Click here)

D
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO ECM (CANH, CANL)
A

REPLACE ECM (Click here)

32. CONNECT CONNECTOR
  1. Reconnect the E72 No. 1 junction connector connector.


NEXT


33. CHECK FOR SHORT IN CAN BUS WIRES (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)

  1. E186808E34
    Disconnect the E69 No. 2 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E69-1 (CANH) - E69-12 (CANL)
    Ignition switch off
    1 MΩ or higher

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 2 Junction Connector)



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 1 JUNCTION CONNECTOR - NO. 2 JUNCTION CONNECTOR)
OK


34. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR SIDE)

  1. E194588E09
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E22-6 (CANH) - E22-14 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *1
    DLC3



NG
Go to step 39
OK


35. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - DISPLAY AND NAVIGATION MODULE DISPLAY)

NOTICE:
For vehicles without the navigation system, go to "Check for Short in CAN Bus Wires (No. 2 Junction Connector - Air Conditioning Amplifier)".

  1. E186808E35
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E69-2 (CANH) - E69-13 (CANL)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 2 Junction Connector)



NG
Go to step 37
OK


36. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - AIR CONDITIONING AMPLIFIER)

  1. E186808E36
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E69-5 (CANH) - E69-16 (CANL)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 2 Junction Connector)



NG
Go to step 38
OK

REPAIR OR REPLACE NO. 2 JUNCTION CONNECTOR

37. CHECK FOR SHORT IN CAN BUS WIRES (DISPLAY AND NAVIGATION MODULE DISPLAY)

  1. E186808E35
    Disconnect the F64 display and navigation module display connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E69-2 (CANH) - E69-13 (CANL)
    Ignition switch off
    1 MΩ or higher

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 2 Junction Connector)



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO DISPLAY AND NAVIGATION MODULE DISPLAY (CANH, CANL)
OK

REPLACE DISPLAY AND NAVIGATION MODULE DISPLAY (Click here)

38. CHECK FOR SHORT IN CAN BUS WIRES (AIR CONDITIONING AMPLIFIER)

  1. E186808E36
    Disconnect the E35*1 or E81*2 air conditioning amplifier connector.
    1. *1: w/ Rear Air Conditioning System
    2. *2: w/o Rear Air Conditioning System

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E69-5 (CANH) - E69-16 (CANL)
    Ignition switch off
    1 MΩ or higher

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 2 Junction Connector)



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO AIR CONDITIONING AMPLIFIER (CANH, CANL)
OK

REPLACE AIR CONDITIONING AMPLIFIER (Click here)

39. CONNECT CONNECTOR
  1. Reconnect the E69 No. 2 junction connector connector.


NEXT


40. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 JUNCTION CONNECTOR - NO. 6 JUNCTION CONNECTOR)

  1. E186808E68
    except Double Swing Out Type:
    1. Disconnect the F21 No. 6 junction connector connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      F21-3 (CANH) - F21-14 (CANL)
      Ignition switch off
      108 to 132 Ω
      Text in Illustration 
      *1
      Rear view of wire harness connector
      (to No. 6 Junction Connector)

  1. E186808E71
    for Double Swing Out Type:
    1. Disconnect the F73 No. 6 junction connector connector.

    2. Measure the resistance according to the value(s) in the table below.

      Standard Resistance:
      Tester Connection
      Switch Condition
      Specified Condition
      F73-7 (CANH) - F73-18 (CANL)
      Ignition switch off
      108 to 132 Ω
      Text in Illustration 
      *1
      Rear view of wire harness connector
      (to No. 6 Junction Connector)



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 2 JUNCTION CONNECTOR - NO. 6 JUNCTION CONNECTOR)
OK


41. CHECK FOR SHORT IN CAN BUS WIRES (NO. 6 JUNCTION CONNECTOR SIDE)

  1. E194588E09
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E22-6 (CANH) - E22-14 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *1
    DLC3
    Result 
    Result
    Proceed to
    OK (w/ TOYOTA parking assist-sensor system)
    A
    OK (w/o TOYOTA parking assist-sensor system)
    B
    NG
    C



B
REPAIR OR REPLACE NO. 6 JUNCTION CONNECTOR

C
Go to step 44
A


42. CHECK FOR SHORT IN CAN BUS WIRES (NO. 6 JUNCTION CONNECTOR - CLEARANCE WARNING ECU)

  1. E186808E70
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F21-1 (CANH) - F21-12 (CANL)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 6 Junction Connector)



NG
Go to step 43
OK

REPAIR OR REPLACE NO. 6 JUNCTION CONNECTOR

43. CHECK FOR SHORT IN CAN BUS WIRES (CLEARANCE WARNING ECU)

  1. E186808E70
    Disconnect the F12 clearance warning ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    F21-1 (CANH) - F21-12 (CANL)
    Ignition switch off
    1 MΩ or higher

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 6 Junction Connector)



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CLEARANCE WARNING ECU (CANH, CANL)
OK

REPLACE CLEARANCE WARNING ECU (Click here)

44. CONNECT CONNECTOR
  1. Reconnect the F21 No. 6 junction connector connector.


NEXT


45. CHECK FOR SHORT IN CAN BUS WIRES (NO. 6 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)

  1. E186808E38
    Disconnect the E75 No. 3 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E75-1 (CANH) - E75-12 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 3 Junction Connector)



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 6 JUNCTION CONNECTOR - NO. 3 JUNCTION CONNECTOR)
OK


46. CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - MAIN BODY ECU)

  1. E186808E39
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E75-4 (CANH) - E75-15 (CANL)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 3 Junction Connector)



NG
Go to step 49
OK


47. CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - SKID CONTROL ECU)

  1. E186808E69
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E75-5 (CANH) - E75-16 (CANL)
    Ignition switch off
    200 Ω or higher

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 3 Junction Connector)



NG
Go to step 50
OK


48. CHECK FOR SHORT IN CAN BUS WIRES (NO. 3 JUNCTION CONNECTOR - COMBINATION METER)

  1. E186808E40
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E75-3 (CANH) - E75-14 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 3 Junction Connector)



NG
Go to step 51
OK

REPAIR OR REPLACE NO. 3 JUNCTION CONNECTOR

49. CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU)

  1. E186808E39
    Disconnect the E3 main body ECU (cowl side junction block LH) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E75-4 (CANH) - E75-15 (CANL)
    Ignition switch off
    1 MΩ or higher

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 3 Junction Connector)



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH) (CANH, CANL)
OK

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)

50. CHECK FOR SHORT IN CAN BUS WIRES (SKID CONTROL ECU)

  1. E186808E69
    Disconnect the A24 master cylinder solenoid (skid control ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E75-5 (CANH) - E75-16 (CANL)
    Ignition switch off
    1 MΩ or higher

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 3 Junction Connector)



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO SKID CONTROL ECU (CANH, CANL)
OK

REPLACE MASTER CYLINDER SOLENOID (SKID CONTROL ECU) (Click here)

51. CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER)

  1. E186808E40
    Disconnect the E7 combination meter connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E75-3 (CANH) - E75-14 (CANL)
    Ignition switch off
    1 MΩ or higher

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 3 Junction Connector)
    Result 
    Result
    Proceed to
    OK (w/ Multi-information Display)
    A
    OK (w/o Multi-information Display)
    B
    NG
    C



B
REPLACE COMBINATION METER (Click here)

C
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER (CANH, CANL)
A

REPLACE COMBINATION METER (Click here)


← Open in CAN Main Wire (from Jan 2012)Short in CAN Bus Lines (from Jan 2012) →