2011-2013 Land Cruiser · Service Manual Power Source / Network

U1002 (CAN MS BUS) Lost Communication with Gateway Module (Main body ECU)

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

If 2 or more DTCs are output during the DTC check, one side of the CAN branch wire may be open (One side of the CANH [branch wire]/CANL [branch wire] of the ECU and/or sensor is open).
DTC Code
DTC Detection Condition
Trouble Area
U1002 (CAN MS BUS)
Lost communication with the gateway module (main body ECU).
  1. MS bus circuit
  2. Certification ECU (smart key ECU assembly) branch wire or connector*4
  3. Position control ECU and switch branch wire or connector*2
  4. Outer mirror control ECU branch wire or connector*2
  5. Multiplex tilt and telescopic ECU branch wire or connector*3
  6. Windshield wiper ECU branch wire or connector*1
  7. Main body ECU (cowl side junction block LH) main wire or connector
  8. Combination meter main wire or connector
  9. Accessory bus buffer branch wire or connector
  10. Certification ECU (smart key ECU assembly)*4
  11. Position control ECU and switch*2
  12. Outer mirror control ECU*2
  13. Multiplex tilt and telescopic ECU*3
  14. Windshield wiper ECU*1
  15. Main body ECU (cowl side junction block LH)
  16. Combination meter
  17. Accessory bus buffer
  18. No. 8 junction connector
  19. No. 9 junction connector
  20. No. 10 junction connector
  21. No. 2 CAN junction connector
  1. *1: w/ Rain Sensor
    *2: w/ Seat Memory
    *3: w/ Power Tilt Power Telescopic Steering Column System
    *4: w/ Entry and Start System

WIRING DIAGRAM

C176915E04
E211918E03

INSPECTION PROCEDURE

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.

    CAUTION:
    For vehicles with an SRS system:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


2. CHECK CAN BUS WIRE (MAIN WIRE FOR DISCONNECTION, BUS LINE FOR SHORT CIRCUIT)

  1. E211919E01
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    Resistance Malfunction
    E3-16 (CANP) - E3-15 (CANN)
    Ignition switch off
    54 to 69 Ω
    Below 53 Ω: Short in line
    E3-16 (CANP) - E3-15 (CANN)
    Ignition switch off
    54 to 69 Ω
    70 Ω or higher: Open in CAN main bus line
    E3-16 (CANP) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    Below 6 kΩ: +B short
    E3-15 (CANN) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    Below 6 kΩ: +B short
    E3-16 (CANP) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    Below 200 Ω: Ground short
    E3-15 (CANN) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    Below 200 Ω: Ground short

    Text in Illustration 
    *1
    Component with harness connected
    (Main Body ECU)
    *2
    DLC3
    Result 
    Result
    Proceed to
    NG
    1. Open in CAN main wire
    A
    NG
    1. Short in line
    2. +B short
    3. Ground short
    B
    OK
    C



B
Go to step 18

C
Go to step 51
A


3. CHECK FOR OPEN IN MAIN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR - MAIN BODY ECU)

  1. C175832E05
    Disconnect the L29 No. 2 CAN junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    L29-1 (CANH) - L29-2 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 2 CAN Junction Connector)



NG
Go to step 5
OK


4. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 2 CAN JUNCTION CONNECTOR - COMBINATION METER)

  1. C175832E06
    Disconnect the L30 No. 2 CAN junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    L30-1 (CANH) - L30-2 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 2 CAN Junction Connector)



NG
Go to step 10
OK

REPAIR OR REPLACE NO. 2 CAN JUNCTION CONNECTOR

5. CONNECT CONNECTOR
  1. Reconnect the L29 No. 2 CAN junction connector connector.


NEXT


6. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 8 JUNCTION CONNECTOR - MAIN BODY ECU)

  1. E211920E01
    Disconnect the E76 No. 8 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E76-6 (CANH) - E76-17 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 8 Junction Connector)



NG
Go to step 8
OK


7. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 8 JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)

  1. E211920E02
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E76-1 (CANH) - E76-12 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 8 Junction Connector)



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 8 JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)
OK

REPAIR OR REPLACE NO. 8 JUNCTION CONNECTOR

8. CONNECT CONNECTOR
  1. Reconnect the E76 No. 8 junction connector connector.


NEXT


9. CHECK FOR OPEN IN CAN BUS MAIN WIRE (MAIN BODY ECU - NO. 8 JUNCTION CONNECTOR)

  1. E211922E01
    Disconnect the E3 main body ECU (cowl side junction block LH) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E3-16 (CANP) - E3-15 (CANN)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to Main Body ECU)



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH) (MAIN BODY ECU - NO. 8 JUNCTION CONNECTOR)
OK

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)

10. CONNECT CONNECTOR
  1. Reconnect the L29 and L30 No. 2 CAN junction connector connectors.


NEXT


11. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 9 JUNCTION CONNECTOR - NO. 10 JUNCTION CONNECTOR)

  1. E211920E03
    Disconnect the E70 No. 10 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E70-1 (CANH) - E70-12 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 10 Junction Connector)



NG
Go to step 15
OK


12. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 10 JUNCTION CONNECTOR - COMBINATION METER)

  1. E211920E04
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E70-3 (CANH) - E70-14 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 10 Junction Connector)



NG
Go to step 13
OK

REPAIR OR REPLACE NO. 10 CAN JUNCTION CONNECTOR

13. CONNECT CONNECTOR
  1. Reconnect the E70 No. 10 junction connector connector.


NEXT


14. CHECK FOR OPEN IN CAN BUS MAIN WIRE (COMBINATION METER - NO. 10 JUNCTION CONNECTOR)

  1. E211921E01
    Disconnect the E7 combination meter connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E7-1 (MPX+) - E7-2 (MPX-)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Combination Meter)
    Result 
    Result
    Proceed to
    OK (w/ Multi-information Display)
    A
    OK (w/o Multi-information Display)
    B
    NG
    C



B
REPLACE COMBINATION METER (Click here)

C
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER (COMBINATION METER - NO. 10 JUNCTION CONNECTOR)
A

REPLACE COMBINATION METER (Click here)

15. CONNECT CONNECTOR
  1. Reconnect the E70 No. 10 junction connector connector.


NEXT


16. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 9 JUNCTION CONNECTOR - NO. 10 JUNCTION CONNECTOR)

  1. E211920E05
    Disconnect the E73 No. 9 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E73-1 (CANH) - E73-12 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 9 Junction Connector)



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 9 JUNCTION CONNECTOR - NO. 10 JUNCTION CONNECTOR)
OK


17. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 2 CAN JUNCTION CONNECTOR - NO. 9 JUNCTION CONNECTOR)

  1. E211920E06
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E73-2 (CANH) - E73-13 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 9 Junction Connector)



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 2 CAN JUNCTION CONNECTOR - NO. 9 JUNCTION CONNECTOR)
OK

REPAIR OR REPLACE NO. 9 JUNCTION CONNECTOR

18. CHECK FOR SHORT IN CAN BUS WIRES (NO. 10 JUNCTION CONNECTOR SIDE)

  1. E211919E01
    Disconnect the E70 No. 10 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E3-16 (CANP) - E3-15 (CANN)
    Ignition switch off
    108 to 132 Ω
    E3-16 (CANP) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E3-15 (CANN) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E3-16 (CANP) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E3-15 (CANN) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *1
    Component with harness connected
    (Main Body ECU)
    *2
    DLC3



NG
Go to step 20
OK


19. CHECK FOR SHORT IN CAN BUS WIRES (NO. 10 JUNCTION CONNECTOR - COMBINATION METER)

  1. C175844E16
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E70-3 (CANH) - E70-14 (CANN)
    Ignition switch off
    108 to 132 Ω
    E70-3 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E70-14 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E70-3 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E70-14 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 10 Junction Connector)
    *2
    DLC3



NG
Go to step 35
OK

REPAIR OR REPLACE NO. 10 JUNCTION CONNECTOR

20. CONNECT CONNECTOR
  1. Reconnect the E70 No. 10 junction connector connector.


NEXT


21. CHECK FOR SHORT IN CAN BUS WIRES (NO. 10 JUNCTION CONNECTOR - NO. 9 JUNCTION CONNECTOR)

  1. C175844E17
    Disconnect the E73 No. 9 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E73-1 (CANH) - E73-12 (CANL)
    Ignition switch off
    108 to 132 Ω
    E73-1 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E73-12 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E73-1 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E73-12 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 9 Junction Connector)
    *2
    DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 10 JUNCTION CONNECTOR - NO. 9 JUNCTION CONNECTOR)
OK


22. CHECK FOR SHORT IN CAN BUS WIRES (NO. 9 JUNCTION CONNECTOR SIDE)

  1. E211919E01
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E3-16 (CANP) - E3-15 (CANN)
    Ignition switch off
    108 to 132 Ω
    E3-16 (CANP) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E3-15 (CANN) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E3-16 (CANP) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E3-15 (CANN) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *1
    Component with harness connected
    (Main Body ECU)
    *2
    DLC3
    Result 
    Result
    Proceed to
    OK (w/ Rain Sensor)
    A
    OK (w/o Rain Sensor)
    B
    NG
    C



B
Go to step 24

C
Go to step 25
A


23. CHECK FOR SHORT IN CAN BUS WIRES (NO. 9 JUNCTION CONNECTOR - WINDSHIELD WIPER ECU)

  1. C175844E18
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E73-4 (CANH) - E73-15 (CANL)
    Ignition switch off
    200 Ω or higher
    E73-4 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E73-15 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E73-4 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E73-15 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 9 Junction Connector)
    *2
    DLC3



NG
Go to step 37
OK


24. CHECK FOR SHORT IN CAN BUS WIRES (NO. 9 JUNCTION CONNECTOR - ACCESSORY BUS BUFFER)

  1. C175844E19
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E73-3 (CANH) - E73-14 (CANL)
    Ignition switch off
    200 Ω or higher
    E73-3 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E73-14 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E73-3 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E73-14 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 9 Junction Connector)
    *2
    DLC3



NG
Go to step 39
OK

REPAIR OR REPLACE NO. 9 JUNCTION CONNECTOR

25. CONNECT CONNECTOR
  1. Reconnect the E73 No. 9 junction connector connector.


NEXT


26. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION CONNECTOR - NO. 9 JUNCTION CONNECTOR)

  1. C175841E10
    Disconnect the L30 No. 2 CAN junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    L30-1 (CANH) - L30-2 (CANL)
    Ignition switch off
    108 to 132 Ω
    L30-1 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    L30-2 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    L30-1 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    L30-2 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 2 CAN Junction Connector)
    *2
    DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 2 CAN JUNCTION CONNECTOR - NO. 9 JUNCTION CONNECTOR)
OK


27. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION CONNECTOR - NO. 8 JUNCTION CONNECTOR)

  1. C175841E11
    Disconnect the L29 No. 2 CAN junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    L29-1 (CANH) - L29-2 (CANL)
    Ignition switch off
    108 to 132 Ω
    L29-1 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    L29-2 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    L29-1 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    L29-2 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 2 CAN Junction Connector)
    *2
    DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 8 JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)
OK


28. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION CONNECTOR SIDE)

  1. E211919E01
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E3-16 (CANP) - E3-15 (CANN)
    Ignition switch off
    108 to 132 Ω
    E3-16 (CANP) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E3-15 (CANN) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E3-16 (CANP) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E3-15 (CANN) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *1
    Component with harness connected
    (Main Body ECU)
    *2
    DLC3



NG
Go to step 29
OK

REPLACE NO. 2 CAN JUNCTION CONNECTOR

29. CONNECT CONNECTOR
  1. Reconnect the L29 and L30 No. 2 CAN junction connector connectors.


NEXT


30. CHECK FOR SHORT IN CAN BUS WIRES (NO. 8 JUNCTION CONNECTOR - CERTIFICATION ECU)

NOTICE:
For vehicles without the entry and start system, go to "Check for Short in CAN Bus Wires (No. 8 Junction Connector - Position Control and Switch)".

  1. C175835E14
    Disconnect the E76 No. 8 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E76-2 (CANH) - E76-13 (CANL)
    Ignition switch off
    200 Ω or higher
    E76-2 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E76-13 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E76-2 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E76-13 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 8 Junction Connector)
    *2
    DLC3



NG
Go to step 41
OK


31. CHECK FOR SHORT IN CAN BUS WIRES (NO. 8 JUNCTION CONNECTOR - POSITION CONTROL AND SWITCH)

NOTICE:
For vehicles without the seat memory, go to "Check for Short in CAN Bus Wires (No. 8 Junction Connector - Multiplex Tilt and Telescopic ECU)".

  1. C175835E15
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E76-4 (CANH) - E76-15 (CANL)
    Ignition switch off
    200 Ω or higher
    E76-4 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E76-15 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E76-4 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E76-15 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 8 Junction Connector)
    *2
    DLC3



NG
Go to step 43
OK


32. CHECK FOR SHORT IN CAN BUS WIRES (NO. 8 JUNCTION CONNECTOR - OUTER MIRROR CONTROL ECU)

  1. C175835E16
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E76-5 (CANH) - E76-16 (CANL)
    Ignition switch off
    200 Ω or higher
    E76-5 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E76-16 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E76-5 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E76-16 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 8 Junction Connector)
    *2
    DLC3



NG
Go to step 45
OK


33. CHECK FOR SHORT IN CAN BUS WIRES (NO. 8 JUNCTION CONNECTOR - MULTIPLEX TILT AND TELESCOPIC ECU)

NOTICE:
For vehicles without the power tilt and power telescopic steering column system, go to "Check for Short in CAN Bus Wires (No. 8 Junction Connector - Main Body ECU)".

  1. C175835E17
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E76-3 (CANH) - E76-14 (CANL)
    Ignition switch off
    200 Ω or higher
    E76-3 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E76-14 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E76-3 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E76-14 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 8 Junction Connector)
    *2
    DLC3



NG
Go to step 47
OK


34. CHECK FOR SHORT IN CAN BUS WIRES (NO. 8 JUNCTION CONNECTOR - MAIN BODY ECU)

  1. C175835E18
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E76-6 (CANH) - E76-17 (CANL)
    Ignition switch off
    108 to 132 Ω
    E76-6 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E76-17 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E76-6 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E76-17 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to No. 8 Junction Connector)
    *2
    DLC3



NG
Go to step 49
OK

REPAIR OR REPLACE NO. 8 JUNCTION CONNECTOR

35. CONNECT CONNECTOR
  1. Reconnect the E70 No. 10 junction connector connector.


NEXT


36. CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER)
C176288E02
  1. Disconnect the E7 combination meter connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E7-1 (MPX+) - E7-2 (MPX-)
    Ignition switch off
    108 to 132 Ω
    E7-1 (MPX+) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E7-2 (MPX-) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E7-1 (MPX+) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E7-2 (MPX-) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to Combination Meter)
    *2
    DLC3
    Result 
    Result
    Proceed to
    OK (w/ Multi-information Display)
    A
    OK (w/o Multi-information Display)
    B
    NG
    C



B
REPLACE COMBINATION METER (Click here)

C
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER (MPX+, MPX-)
A

REPLACE COMBINATION METER (Click here)

37. CONNECT CONNECTOR
  1. Reconnect the E73 No. 9 junction connector connector.


NEXT


38. CHECK FOR SHORT IN CAN BUS WIRES (WINDSHIELD WIPER ECU)

  1. C176954E05
    Disconnect the E85 windshield wiper ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E85-6 (CANH) - E85-5 (CANL)
    Ignition switch off
    54 to 69 Ω
    E85-6 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E85-5 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E85-6 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E85-5 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Windshield Wiper ECU)
    *2
    DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO WINDSHIELD WIPER ECU (CANH, CANL)
OK

REPLACE WINDSHIELD WIPER ECU (Click here)

39. CONNECT CONNECTOR
  1. Reconnect the E73 No. 9 junction connector connector.


NEXT


40. CHECK FOR SHORT IN CAN BUS WIRES (ACCESSORY BUS BUFFER WIRE)

  1. E211923E01
    Disconnect the E6 accessory bus buffer connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E6-1 (CAN+) - E6-2 (CAN-)
    Ignition switch off
    54 to 69 Ω
    E6-1 (CAN+) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E6-2 (CAN-) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E6-1 (CAN+) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E6-2 (CAN-) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Accessory Bus Buffer Connector)
    *2
    DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO ACCESSORY BUS BUFFER (CANH, CANL)
OK

REPLACE ACCESSORY BUS BUFFER

41. CONNECT CONNECTOR
  1. Reconnect the E76 No. 8 junction connector connector.


NEXT


42. CHECK FOR SHORT IN CAN BUS WIRES (CERTIFICATION ECU)

  1. C175836E02
    Disconnect the E29 certification ECU (smart key ECU assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E29-27 (CANH) - E29-28 (CANL)
    Ignition switch off
    54 to 69 Ω
    E29-27 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E29-28 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E29-27 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E29-28 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Certification ECU)
    *2
    DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (CANH, CANL)
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

43. CONNECT CONNECTOR
  1. Reconnect the E76 No. 8 junction connector connector.


NEXT


44. CHECK FOR SHORT IN CAN BUS WIRES (POSITION CONTROL AND SWITCH)

  1. C175837E04
    Disconnect the c15 position control ECU and switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    c15-5 (MPX1) - c15-1 (MPX2)
    Ignition switch off
    54 to 69 Ω
    c15-5 (MPX1) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    c15-1 (MPX2) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    c15-5 (MPX1) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    c15-1 (MPX2) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Position Control ECU and Switch)
    *2
    DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO POSITION CONTROL ECU AND SWITCH (MPX1, MPX2)
OK

REPLACE POSITION CONTROL ECU AND SWITCH (Click here)

45. CONNECT CONNECTOR
  1. Reconnect the E76 No. 8 junction connector connector.


NEXT


46. CHECK FOR SHORT IN CAN BUS WIRES (OUTER MIRROR CONTROL ECU)

  1. C175839E05
    Disconnect the I18 outer mirror control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    I18-1 (CANH) - I18-21 (CANL)
    Ignition switch off
    54 to 69 Ω
    I18-1 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    I18-21 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    I18-1 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    I18-21 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Outer Mirror Control ECU)
    *2
    DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO OUTER MIRROR CONTROL ECU (CANH, CANL)
OK

REPLACE OUTER MIRROR CONTROL ECU (Click here)

47. CONNECT CONNECTOR
  1. Reconnect the E76 No. 8 junction connector connector.


NEXT


48. CHECK FOR SHORT IN CAN BUS WIRES (MULTIPLEX TILT AND TELESCOPIC ECU)

  1. C175838E02
    Disconnect the E27 power tilt and telescopic ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E27-5 (CANP) - E27-14 (CANN)
    Ignition switch off
    54 to 69 Ω
    E27-5 (CANP) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E27-14 (CANN) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E27-5 (CANP) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E27-14 (CANN) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Multiplex Tilt and Telescopic ECU)
    *2
    DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO POWER TILT AND TELESCOPIC ECU (CANP, CANN)
OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU (Click here)

49. CONNECT CONNECTOR
  1. Reconnect the E76 No. 8 junction connector connector.


NEXT


50. CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU)

  1. C175840E02
    Disconnect the E3 main body ECU (cowl side junction block LH) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E3-16 (CANP) - E3-15 (CANN)
    Ignition switch off
    108 to 132 Ω
    E3-16 (CANP) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E3-15 (CANN) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E3-16 (CANP) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E3-15 (CANN) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *1
    Rear view of wire harness connector
    (to Main Body ECU)
    *2
    DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH) (CANP, CANN)
OK

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)

51. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY AND BODY GROUND)

  1. E211924E01
    Connect the cable to the negative (-) battery terminal.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Disconnect the 2A, 2D and E3 main body ECU (cowl side junction block LH) connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2D-62 (GND2) - Body ground
    Always
    Below 1 Ω
    E3-1 (GND3) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    2A-1 (ALTB) - Body ground
    Always
    11 to 14 V

    Text in Illustration 
    *1
    Front view of wire harness connector
    (to Main Body ECU)



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)


← U0327 Software Incompatibility with Vehicle Security Control Module (from Jan 2012)U1002 (CAN MS BUS) Lost Communication with Gateway Module (Main body ECU) (from Jan 2012) →