U1002 (CAN MS BUS) Lost Communication with Gateway Module (Main body ECU)
Diagnostic trouble codes · Vehicles built from Jan 2012
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
DESCRIPTION
- The main body ECU stores this DTC when no signals can be received from the ECUs that have been memorized as those connected to the CAN MS bus.
- When the main body ECU receives a response signal from the ECUs connected to the CAN MS bus, the main body ECU recognizes and memorizes that the ECU is connected to the CAN MS bus. Based on this memorized data, the main body ECU monitors for malfunctions in the ECUs connected to the CAN MS bus when communicating with those ECUs. If the main body ECU cannot receive response signals from the ECUs that have been memorized as those connected to the CAN MS bus, the main body ECU determines that a malfunction exists.
- If 2 or more DTCs are output during the DTC check, one side of the CAN branch wire may be open (one side of the CANH [CAN branch wire]/CANL [CAN branch wire] of the ECU and/or sensor is open).
| DTC Code |
DTC Detection Condition |
Trouble Area |
| U1002 (CAN MS BUS) |
Lost communication with the gateway module (main body ECU). |
|
- *1: w/ Rain Sensor
- *2: w/ Seat Memory
- *3: w/ Power Tilt Power Telescopic Steering Column System
- *4: w/ Entry and Start System
- *5: w/ Power Back Door System
WIRING DIAGRAM




INSPECTION PROCEDURE
- HINT:
- Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.
| 1. PRECAUTION |
- NOTICE:
- After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).
| NEXT | |
| 2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL |
Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.
- CAUTION:
- For vehicles with an SRS system:
- Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.
- NOTICE:
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).
| NEXT | |
| 3. CHECK CAN BUS WIRE (CAN MAIN WIRE FOR DISCONNECTION, CHECK BUS LINE FOR SHORT CIRCUIT) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
Resistance Malfunction
E3-16 (CANP) - E3-15 (CANN)
Ignition switch off
54 to 69 Ω
Below 53 Ω: Short in line
E3-16 (CANP) - E3-15 (CANN)
Ignition switch off
54 to 69 Ω
70 Ω or higher: Open in CAN main bus line
E3-16 (CANP) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
Below 6 kΩ: +B short
E3-15 (CANN) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
Below 6 kΩ: +B short
E3-16 (CANP) - E22-4 (CG)
Ignition switch off
200 Ω or higher
Below 200 Ω: Ground short
E3-15 (CANN) - E22-4 (CG)
Ignition switch off
200 Ω or higher
Below 200 Ω: Ground short
Text in Illustration *a
Component with harness connected
(Main Body ECU [Cowl Side Junction Block LH])
*b
Front view of DLC3
Result Result
Proceed to
NG - Open in CAN main wire
A
NG - Short in line
- +B short
- Ground short
B
OK
C
|
|
||||
|
|
||||
| A | |
| 4. CHECK FOR OPEN IN MAIN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR - MAIN BODY ECU) |
Disconnect the L29 No. 2 CAN junction connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
L29-1 (CANH) - L29-2 (CANL)
Ignition switch off
108 to 132 Ω
Text in Illustration *a
Rear view of wire harness connector
(to No. 2 CAN Junction Connector)
|
|
||||
| OK | |
| 5. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 2 CAN JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY) |
Disconnect the L30 No. 2 CAN junction connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
L30-1 (CANH) - L30-2 (CANL)
Ignition switch off
108 to 132 Ω
Text in Illustration *a
Rear view of wire harness connector
(to No. 2 CAN Junction Connector)
|
|
||||
| OK | ||
| ||
| 6. CONNECT CONNECTOR |
Reconnect the L29 No. 2 CAN junction connector.
| NEXT | |
| 7. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 8 JUNCTION CONNECTOR - MAIN BODY ECU) |
Disconnect the E76 No. 8 junction connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E76-6 (CANH) - E76-17 (CANL)
Ignition switch off
108 to 132 Ω
Text in Illustration *a
Rear view of wire harness connector
(to No. 8 Junction Connector)
|
|
||||
| OK | |
| 8. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 8 JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E76-1 (CANH) - E76-12 (CANL)
Ignition switch off
108 to 132 Ω
Text in Illustration *a
Rear view of wire harness connector
(to No. 8 Junction Connector)
|
|
||||
| OK | ||
| ||
| 9. CONNECT CONNECTOR |
Reconnect the E76 No. 8 junction connector.
| NEXT | |
| 10. CHECK FOR OPEN IN CAN BUS MAIN WIRE (MAIN BODY ECU - NO. 8 JUNCTION CONNECTOR) |
Disconnect the E3 main body ECU (cowl side junction block LH) connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E3-16 (CANP) - E3-15 (CANN)
Ignition switch off
108 to 132 Ω
Text in Illustration *a
Rear view of wire harness connector
(to Main Body ECU [Cowl Side Junction Block LH])
|
|
||||
| OK | ||
| ||
| 11. CONNECT CONNECTOR |
Reconnect the L29 and L30 No. 2 CAN junction connectors.
| NEXT | |
| 12. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 10 JUNCTION CONNECTOR - NO. 9 JUNCTION CONNECTOR) |
Disconnect the E70 No. 10 junction connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E70-1 (CANH) - E70-12 (CANL)
Ignition switch off
108 to 132 Ω
Text in Illustration *a
Rear view of wire harness connector
(to No. 10 Junction Connector)
|
|
||||
| OK | |
| 13. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 10 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E70-3 (CANH) - E70-14 (CANL)
Ignition switch off
108 to 132 Ω
Text in Illustration *a
Rear view of wire harness connector
(to No. 10 Junction Connector)
|
|
||||
| OK | ||
| ||
| 14. CONNECT CONNECTOR |
Reconnect the E70 No. 10 junction connector.
| NEXT | |
| 15. CHECK FOR OPEN IN CAN BUS MAIN WIRE (COMBINATION METER ASSEMBLY - NO. 10 JUNCTION CONNECTOR) |
Disconnect the E7 combination meter assembly connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E7-1 (MPX+) - E7-2 (MPX-)
Ignition switch off
108 to 132 Ω
Text in Illustration *a
Front view of wire harness connector
(to Combination Meter Assembly)
Result Result
Proceed to
OK (w/ Multi-information Display)
A
OK (w/o Multi-information Display)
B
NG
C
|
|
||||
|
|
||||
| A | ||
| ||
| 16. CONNECT CONNECTOR |
Reconnect the E70 No. 10 junction connector.
| NEXT | |
| 17. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 9 JUNCTION CONNECTOR - NO. 10 JUNCTION CONNECTOR) |
Disconnect the E73 No. 9 junction connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E73-1 (CANH) - E73-12 (CANL)
Ignition switch off
108 to 132 Ω
Text in Illustration *a
Rear view of wire harness connector
(to No. 9 Junction Connector)
|
|
||||
| OK | |
| 18. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 9 JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E73-2 (CANH) - E73-13 (CANL)
Ignition switch off
108 to 132 Ω
Text in Illustration *a
Rear view of wire harness connector
(to No. 9 Junction Connector)
|
|
||||
| OK | ||
| ||
| 19. CHECK FOR SHORT IN CAN BUS WIRES (NO. 10 JUNCTION CONNECTOR SIDE) |
Disconnect the E70 No. 10 junction connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E3-16 (CANP) - E3-15 (CANN)
Ignition switch off
108 to 132 Ω
E3-16 (CANP) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E3-15 (CANN) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E3-16 (CANP) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
E3-15 (CANN) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
Text in Illustration *a
Component with harness connected
(Main Body ECU [Cowl Side Junction Block LH])
*b
Front view of DLC3
|
|
||||
| OK | |
| 20. CHECK FOR SHORT IN CAN BUS WIRES (NO. 10 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E70-3 (CANH) - E70-14 (CANN)
Ignition switch off
108 to 132 Ω
E70-3 (CANH) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E70-14 (CANL) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E70-3 (CANH) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
E70-14 (CANL) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
Text in Illustration *a
Rear view of wire harness connector
(to No. 10 Junction Connector)
*b
Front view of DLC3
|
|
||||
| OK | ||
| ||
| 21. CONNECT CONNECTOR |
Reconnect the E70 No. 10 junction connector.
| NEXT | |
| 22. CHECK FOR SHORT IN CAN BUS WIRES (NO. 9 JUNCTION CONNECTOR - NO. 10 JUNCTION CONNECTOR) |
Disconnect the E73 No. 9 junction connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E73-1 (CANH) - E73-12 (CANL)
Ignition switch off
108 to 132 Ω
E73-1 (CANH) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E73-12 (CANL) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E73-1 (CANH) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
E73-12 (CANL) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
Text in Illustration *a
Rear view of wire harness connector
(to No. 9 Junction Connector)
*b
Front view of DLC3
|
|
||||
| OK | |
| 23. CHECK FOR SHORT IN CAN BUS WIRES (NO. 9 JUNCTION CONNECTOR SIDE) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E3-16 (CANP) - E3-15 (CANN)
Ignition switch off
108 to 132 Ω
E3-16 (CANP) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E3-15 (CANN) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E3-16 (CANP) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
E3-15 (CANN) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
Text in Illustration *a
Component with harness connected
(Main Body ECU [Cowl Side Junction Block LH])
*b
Front view of DLC3
|
|
||||
| OK | |
| 24. CHECK FOR SHORT IN CAN BUS WIRES (NO. 9 JUNCTION CONNECTOR - WINDSHIELD WIPER ECU) |
- NOTICE:
- For vehicles without an rain sensor, go to "Check for Short in CAN Bus Wires (No. 9 Junction Connector - Accessory Bus Buffer)".
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E73-4 (CANH) - E73-15 (CANL)
Ignition switch off
200 Ω or higher
E73-4 (CANH) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E73-15 (CANL) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E73-4 (CANH) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
E73-15 (CANL) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
Text in Illustration *a
Rear view of wire harness connector
(to No. 9 Junction Connector)
*b
Front view of DLC3
|
|
||||
| OK | |
| 25. CHECK FOR SHORT IN CAN BUS WIRES (NO. 9 JUNCTION CONNECTOR - ACCESSORY BUS BUFFER) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E73-3 (CANH) - E73-14 (CANL)
Ignition switch off
200 Ω or higher
E73-3 (CANH) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E73-14 (CANL) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E73-3 (CANH) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
E73-14 (CANL) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
Text in Illustration *a
Rear view of wire harness connector
(to No. 9 Junction Connector)
*b
Front view of DLC3
|
|
||||
| OK | ||
| ||
| 26. CONNECT CONNECTOR |
Reconnect the E73 No. 9 junction connector.
| NEXT | |
| 27. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION CONNECTOR - NO. 9 JUNCTION CONNECTOR) |
Disconnect the L30 No. 2 CAN junction connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
L30-1 (CANH) - L30-2 (CANL)
Ignition switch off
108 to 132 Ω
L30-1 (CANH) - E22-4 (CG)
Ignition switch off
200 Ω or higher
L30-2 (CANL) - E22-4 (CG)
Ignition switch off
200 Ω or higher
L30-1 (CANH) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
L30-2 (CANL) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
Text in Illustration *a
Rear view of wire harness connector
(to No. 2 CAN Junction Connector)
*b
Front view of DLC3
|
|
||||
| OK | |
| 28. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION CONNECTOR SIDE) |
Disconnect the L29 No. 2 CAN junction connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E3-16 (CANP) - E3-15 (CANN)
Ignition switch off
108 to 132 Ω
E3-16 (CANP) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E3-15 (CANN) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E3-16 (CANP) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
E3-15 (CANN) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
Text in Illustration *a
Component with harness connected
(Main Body ECU [Cowl Side Junction Block LH])
*b
Front view of DLC3
Result Result
Proceed to
OK (w/o Power Back Door System)
A
OK (w/ Power Back Door System)
B
NG
C
|
|
||||
|
|
||||
| A | ||
| ||
| 29. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION CONNECTOR - POWER BACK DOOR ECU) |
Disconnect the L54 No. 2 CAN junction connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
L54-1 (CANH) - L54-2 (CANL)
Ignition switch off
200 Ω or higher
L54-1 (CANH) - E22-4 (CG)
Ignition switch off
200 Ω or higher
L54-2 (CANL) - E22-4 (CG)
Ignition switch off
200 Ω or higher
L54-1 (CANH) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
L54-2 (CANH) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
Text in Illustration *a
Rear view of wire harness connector
(to No. 2 CAN Junction Connector)
*b
Front view of DLC3
|
|
||||
| OK | |
| 30. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION CONNECTOR - NO. 2 MAIN BODY ECU) |
Disconnect the L57 No. 2 CAN junction connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
L57-1 (CANH) - L57-2 (CANL)
Ignition switch off
200 Ω or higher
L57-1 (CANH) - E22-4 (CG)
Ignition switch off
200 Ω or higher
L57-2 (CANL) - E22-4 (CG)
Ignition switch off
200 Ω or higher
L57-1 (CANH) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
L57-2 (CANH) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
Text in Illustration *a
Rear view of wire harness connector
(to No. 2 CAN Junction Connector)
*b
Front view of DLC3
|
|
||||
| OK | ||
| ||
| 31. CONNECT CONNECTOR |
Reconnect the L29 and L30 No. 2 CAN junction connectors.
| NEXT | |
| 32. CHECK FOR SHORT IN CAN BUS WIRES (NO. 8 JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR) |
Disconnect the E76 No. 8 junction connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E76-1 (CANH) - E76-12 (CANL)
Ignition switch off
108 to 132 Ω
E76-1 (CANH) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E76-12 (CANL) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E76-1 (CANH) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
E76-12 (CANL) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
Text in Illustration *a
Rear view of wire harness connector
(to No. 8 Junction Connector)
*b
Front view of DLC3
|
|
||||
| OK | |
| 33. CHECK FOR SHORT IN CAN BUS WIRES (NO. 8 JUNCTION CONNECTOR - CERTIFICATION ECU) |
- NOTICE:
- For vehicles without an entry and start system, go to "Check for Short in CAN Bus Wires (No. 8 Junction Connector - Position Control and Switch)".
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E76-2 (CANH) - E76-13 (CANL)
Ignition switch off
200 Ω or higher
E76-2 (CANH) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E76-13 (CANL) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E76-2 (CANH) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
E76-13 (CANL) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
Text in Illustration *a
Rear view of wire harness connector
(to No. 8 Junction Connector)
*b
Front view of DLC3
|
|
||||
| OK | |
| 34. CHECK FOR SHORT IN CAN BUS WIRES (NO. 8 JUNCTION CONNECTOR - POSITION CONTROL ECU AND SWITCH) |
- NOTICE:
- For vehicles without seat memory, go to "Check for Short in CAN Bus Wires (No. 8 Junction Connector - Multiplex Tilt and Telescopic ECU)".
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E76-4 (CANH) - E76-15 (CANL)
Ignition switch off
200 Ω or higher
E76-4 (CANH) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E76-15 (CANL) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E76-4 (CANH) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
E76-15 (CANL) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
Text in Illustration *a
Rear view of wire harness connector
(to No. 8 Junction Connector)
*b
Front view of DLC3
|
|
||||
| OK | |
| 35. CHECK FOR SHORT IN CAN BUS WIRES (NO. 8 JUNCTION CONNECTOR - OUTER MIRROR CONTROL ECU ASSEMBLY) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E76-5 (CANH) - E76-16 (CANL)
Ignition switch off
200 Ω or higher
E76-5 (CANH) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E76-16 (CANL) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E76-5 (CANH) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
E76-16 (CANL) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
Text in Illustration *a
Rear view of wire harness connector
(to No. 8 Junction Connector)
*b
Front view of DLC3
|
|
||||
| OK | |
| 36. CHECK FOR SHORT IN CAN BUS WIRES (NO. 8 JUNCTION CONNECTOR - MULTIPLEX TILT AND TELESCOPIC ECU) |
- NOTICE:
- For vehicles without a power tilt and power telescopic steering column system, go to "Check for Short in CAN Bus Wires (No. 8 Junction Connector - Main Body ECU)".
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E76-3 (CANH) - E76-14 (CANL)
Ignition switch off
200 Ω or higher
E76-3 (CANH) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E76-14 (CANL) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E76-3 (CANH) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
E76-14 (CANL) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
Text in Illustration *a
Rear view of wire harness connector
(to No. 8 Junction Connector)
*b
Front view of DLC3
|
|
||||
| OK | |
| 37. CHECK FOR SHORT IN CAN BUS WIRES (NO. 8 JUNCTION CONNECTOR - MAIN BODY ECU) |
Measure the resistance according to the value(s) in the table below.

- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E76-6 (CANH) - E76-17 (CANL)
Ignition switch off
108 to 132 Ω
E76-6 (CANH) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E76-17 (CANL) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E76-6 (CANH) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
E76-17 (CANL) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
Text in Illustration *a
Rear view of wire harness connector
(to No. 8 Junction Connector)
*b
Front view of DLC3
|
|
||||
| OK | ||
| ||
| 38. CONNECT CONNECTOR |
Reconnect the E70 No. 10 junction connector.
| NEXT | |
| 39. CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER ASSEMBLY) |
Disconnect the E7 combination meter assembly connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E7-1 (MPX+) - E7-2 (MPX-)
Ignition switch off
108 to 132 Ω
E7-1 (MPX+) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E7-2 (MPX-) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E7-1 (MPX+) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
E7-2 (MPX-) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
Text in Illustration *a
Front view of wire harness connector
(to Combination Meter Assembly)
*b
Front view of DLC3
Result Result
Proceed to
OK (w/ Multi-information Display)
A
OK (w/o Multi-information Display)
B
NG
C
|
|
||||
|
|
||||
| A | ||
| ||
| 40. CONNECT CONNECTOR |
Reconnect the E73 No. 9 junction connector.
| NEXT | |
| 41. CHECK FOR SHORT IN CAN BUS WIRES (WINDSHIELD WIPER ECU) |
Disconnect the E85 windshield wiper ECU connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E85-6 (CANH) - E85-5 (CANL)
Ignition switch off
54 to 69 Ω
E85-6 (CANH) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E85-5 (CANL) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E85-6 (CANH) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
E85-5 (CANL) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
Text in Illustration *a
Front view of wire harness connector
(to Windshield Wiper ECU)
*b
Front view of DLC3
|
|
||||
| OK | ||
| ||
| 42. CONNECT CONNECTOR |
Reconnect the E73 No. 9 junction connector.
| NEXT | |
| 43. CHECK FOR SHORT IN CAN BUS WIRES (ACCESSORY BUS BUFFER) |
Disconnect the E6 accessory bus buffer connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E6-1 (CAN+) - E6-2 (CAN-)
Ignition switch off
54 to 69 Ω
E6-1 (CAN+) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E6-2 (CAN-) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E6-1 (CAN+) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
E6-2 (CAN-) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
Text in Illustration *a
Front view of wire harness connector
(to Accessory Bus Buffer)
*b
Front view of DLC3
|
|
||||
| OK | ||
| ||
| 44. CONNECT CONNECTOR |
Reconnect the L29, L30 and L54 No. 2 CAN junction connectors.
| NEXT | |
| 45. CHECK FOR SHORT IN CAN BUS WIRES (POWER BACK DOOR ECU) |
Disconnect the L52 power back door unit assembly (power back door ECU) connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
L52-6 (MPX1) - L52-5 (MPX2)
Ignition switch off
54 to 69 Ω
L52-6 (MPX1) - E22-4 (CG)
Ignition switch off
200 Ω or higher
L52-5 (MPX2) - E22-4 (CG)
Ignition switch off
200 Ω or higher
L52-6 (MPX1) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
L52-5 (MPX2) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
Text in Illustration *a
Rear view of wire harness connector
(to Power Back Door Unit Assembly [Power Back Door ECU])
*b
Front view of DLC3
|
|
||||
| OK | ||
| ||
| 46. CONNECT CONNECTOR |
Reconnect the L29, L30, L54 and L57 No. 2 CAN junction connectors.
| NEXT | |
| 47. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 MAIN BODY ECU) |
Disconnect the L50 No. 2 main body ECU connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
L50-11 (MPX+) - L50-12 (MPX-)
Ignition switch off
54 to 69 Ω
L50-11 (MPX+) - E22-4 (CG)
Ignition switch off
200 Ω or higher
L50-12 (MPX-) - E22-4 (CG)
Ignition switch off
200 Ω or higher
L50-11 (MPX+) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
L50-12 (MPX-) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
Text in Illustration *a
Rear view of wire harness connector
(to No. 2 Main Body ECU)
*b
Front view of DLC3
|
|
||||
| OK | ||
| ||
| 48. CONNECT CONNECTOR |
Reconnect the E76 No. 8 junction connector.
| NEXT | |
| 49. CHECK FOR SHORT IN CAN BUS WIRES (CERTIFICATION ECU) |
Disconnect the E29 certification ECU (smart key ECU assembly) connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E29-27 (CANH) - E29-28 (CANL)
Ignition switch off
54 to 69 Ω
E29-27 (CANH) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E29-28 (CANL) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E29-27 (CANH) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
E29-28 (CANL) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
Text in Illustration *a
Front view of wire harness connector
(to Certification ECU [Smart Key ECU Assembly])
*b
Front view of DLC3
|
|
||||
| OK | ||
| ||
| 50. CONNECT CONNECTOR |
Reconnect the E76 No. 8 junction connector.
| NEXT | |
| 51. CHECK FOR SHORT IN CAN BUS WIRES (POSITION CONTROL ECU AND SWITCH) |
Disconnect the c15 position control ECU and switch connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
c15-5 (MPX1) - c15-1 (MPX2)
Ignition switch off
54 to 69 Ω
c15-5 (MPX1) - E22-4 (CG)
Ignition switch off
200 Ω or higher
c15-1 (MPX2) - E22-4 (CG)
Ignition switch off
200 Ω or higher
c15-5 (MPX1) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
c15-1 (MPX2) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
Text in Illustration *a
Front view of wire harness connector
(to Position Control ECU and Switch)
*b
Front view of DLC3
|
|
||||
| OK | ||
| ||
| 52. CONNECT CONNECTOR |
Reconnect the E76 No. 8 junction connector.
| NEXT | |
| 53. CHECK FOR SHORT IN CAN BUS WIRES (OUTER MIRROR CONTROL ECU ASSEMBLY) |
Disconnect the I18 outer mirror control ECU assembly connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
I18-1 (CANH) - I18-21 (CANL)
Ignition switch off
54 to 69 Ω
I18-1 (CANH) - E22-4 (CG)
Ignition switch off
200 Ω or higher
I18-21 (CANL) - E22-4 (CG)
Ignition switch off
200 Ω or higher
I18-1 (CANH) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
I18-21 (CANL) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
Text in Illustration *a
Front view of wire harness connector
(to Outer Mirror Control ECU Assembly)
*b
Front view of DLC3
|
|
||||
| OK | ||
| ||
| 54. CONNECT CONNECTOR |
Reconnect the E76 No. 8 junction connector.
| NEXT | |
| 55. CHECK FOR SHORT IN CAN BUS WIRES (MULTIPLEX TILT AND TELESCOPIC ECU) |
Disconnect the E27 multiplex tilt and telescopic ECU connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E27-5 (CANP) - E27-14 (CANN)
Ignition switch off
54 to 69 Ω
E27-5 (CANP) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E27-14 (CANN) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E27-5 (CANP) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
E27-14 (CANN) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
Text in Illustration *a
Front view of wire harness connector
(to Multiplex Tilt and Telescopic ECU)
*b
Front view of DLC3
|
|
||||
| OK | ||
| ||
| 56. CONNECT CONNECTOR |
Reconnect the E76 No. 8 junction connector.
| NEXT | |
| 57. CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU) |
Disconnect the E3 main body ECU (cowl side junction block LH) connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
E3-16 (CANP) - E3-15 (CANN)
Ignition switch off
108 to 132 Ω
E3-16 (CANP) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E3-15 (CANN) - E22-4 (CG)
Ignition switch off
200 Ω or higher
E3-16 (CANP) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
E3-15 (CANN) - E22-16 (BAT)
Ignition switch off
6 kΩ or higher
Text in Illustration *a
Rear view of wire harness connector
(to Main Body ECU [Cowl Side Junction Block LH])
*b
Front view of DLC3
|
|
||||
| OK | ||
| ||
| 58. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY AND BODY GROUND) |
Connect the cable to the negative (-) battery terminal.


Text in Illustration *a
Front view of wire harness connector
(to Main Body ECU [Cowl Side Junction Block LH])
*b
Rear view of wire harness connector
(to Main Body ECU [Cowl Side Junction Block LH])
- NOTICE:
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).
Disconnect the E3, 2A and 2D main body ECU (cowl side junction block LH) connectors.
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
2A-1 (ALTB) - Body ground
Always
11 to 14 V
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
2D-62 (GND2) - Body ground
Always
Below 1 Ω
E3-1 (GND3) - Body ground
Always
Below 1 Ω
|
|
||||
| OK | ||
| ||
