2011-2013 Land Cruiser · Service Manual Power Source / Network

U1002 (CAN MS BUS) Lost Communication with Gateway Module (Main body ECU)

Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

If 2 or more DTCs are output during the DTC check, one side of the CAN branch wire may be open (One side of the CANH [branch wire]/CANL [branch wire] of the ECU and/or sensor is open).
DTC Code
Symptom
Trouble Area
U1002 (CAN MS BUS)
Lost communication with the gateway module (main body ECU).
  1. MS bus circuit
  2. Main body ECU main wire or connector
  3. Windshield wiper ECU branch wire or connector*1
  4. Position control ECU and switch branch wire or connector*2
  5. Certification ECU (smart key ECU assembly) branch wire or connector*4
  6. Multiplex tilt and telescopic ECU branch wire or connector*3
  7. Outer mirror control ECU branch wire or connector*2
  8. Combination meter main wire or connector
  9. Main body ECU
  10. Windshield wiper ECU*1
  11. Position control ECU and switch*2
  12. Certification ECU (smart key ECU assembly)*4
  13. Multiplex tilt and telescopic ECU*3
  14. Outer mirror control ECU*2
  15. Combination meter
  16. No. 8 junction connector
  17. No. 9 junction connector
  18. No. 10 junction connector
  19. No. 2 CAN junction connector

HINT:
*1: w/ Rain Sensor
*2: w/ Seat Memory
*3: w/ Power Tilt and Power Telescopic Steering Column System
*4: w/ Entry and Start System


WIRING DIAGRAM

C176039E01
C176040E03

INSPECTION PROCEDURE


1. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the main wire and the branch wire.

    CAUTION:
    For vehicles with an SRS system:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


2. CHECK CAN BUS WIRE (MAIN WIRE FOR DISCONNECTION, BUS LINE FOR SHORT CIRCUIT)

  1. C174933E02
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    Resistance Malfunction
    E3-16 (CANP) - E3-15 (CANN)
    Ignition switch off
    54 to 69 Ω
    Below 53 Ω: Short in line
    E3-16 (CANP) - E3-15 (CANN)
    Ignition switch off
    54 to 69 Ω
    70 Ω or higher: Open in CAN main bus line
    E3-16 (CANP) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    Below 6 kΩ: +B short
    E3-15 (CANN) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    Below 6 kΩ: +B short
    E3-16 (CANP) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    Below 200 Ω: Ground short
    E3-15 (CANN) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    Below 200 Ω: Ground short

    Result 
    Result
    Proceed to
    NG
    - Open in CAN main wire
    A
    NG
    - Short in line
    - +B short
    - Ground short
    B
    OK
    C



B
Go to step 18

C
Go to step 48
A


3. CHECK FOR OPEN IN MAIN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR - MAIN BODY ECU)

  1. C175832E01
    Disconnect the L29 No. 2 CAN junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    L29-1 (CANH) - L29-2 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
Go to step 5
OK


4. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 2 CAN JUNCTION CONNECTOR - COMBINATION METER)

  1. C175832E03
    Disconnect the L30 No. 2 CAN junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    L30-1 (CANH) - L30-2 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
Go to step 10
OK

REPLACE NO. 2 CAN JUNCTION CONNECTOR

5. CONNECT CONNECTOR
  1. Reconnect the L29 No. 2 CAN junction connector connector.


NEXT


6. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 8 JUNCTION CONNECTOR - MAIN BODY ECU)

  1. C174233E37
    Disconnect the E73 No. 8 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E73-3 (CANH) - E73-14 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
Go to step 8
OK


7. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 8 JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)

  1. C174233E38
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E73-1 (CANH) - E73-12 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 8 JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)
OK

REPAIR OR REPLACE NO. 8 JUNCTION CONNECTOR

8. CONNECT CONNECTOR
  1. Reconnect the E73 No. 8 junction connector connector.


NEXT


9. CHECK FOR OPEN IN CAN BUS MAIN WIRE (MAIN BODY ECU - NO. 8 JUNCTION CONNECTOR)

  1. C175845E01
    Disconnect the E3 main body ECU (cowl side junction block LH) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E3-16 (CANP) - E3-15 (CANN)
    Ignition switch off
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH) (MAIN BODY ECU - NO. 8 JUNCTION CONNECTOR)
OK

REPLACE MAIN BODY ECU

10. CONNECT CONNECTOR
  1. Reconnect the L29 and L30 No. 2 CAN junction connector connectors.


NEXT


11. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 9 JUNCTION CONNECTOR - NO. 10 JUNCTION CONNECTOR)

  1. C174233E18
    Disconnect the E70 No. 10 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E70-1 (CANH) - E70-12 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
Go to step 15
OK


12. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 10 JUNCTION CONNECTOR - COMBINATION METER)

  1. C174233E19
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E70-3 (CANH) - E70-14 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
Go to step 13
OK

REPAIR OR REPLACE NO. 10 CAN JUNCTION CONNECTOR

13. CONNECT CONNECTOR
  1. Reconnect the E70 No. 10 junction connector connector.


NEXT


14. CHECK FOR OPEN IN CAN BUS MAIN WIRE (COMBINATION METER - NO. 10 JUNCTION CONNECTOR)

  1. C170369E07
    Disconnect the E7 combination meter connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E7-1 (MPX+) - E7-2 (MPX-)
    Ignition switch off
    108 to 132 Ω

    Result 
    Result
    Proceed to
    OK (w/ Multi-information Display)
    A
    OK (w/o Multi-information Display)
    B
    NG
    C



B
REPLACE COMBINATION METER ASSEMBLY (Click here)

C
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER (COMBINATION METER - NO. 10 JUNCTION BLOCK)
A

REPLACE COMBINATION METER ASSEMBLY (Click here)

15. CONNECT CONNECTOR
  1. Reconnect the E70 No. 10 junction connector connector.


NEXT


16. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 9 JUNCTION CONNECTOR - NO. 10 JUNCTION CONNECTOR)

  1. C174233E39
    Disconnect the E76 No. 9 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E76-1 (CANH) - E76-12 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 9 JUNCTION CONNECTOR - NO. 10 JUNCTION CONNECTOR)
OK


17. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 2 CAN JUNCTION CONNECTOR - NO. 9 JUNCTION CONNECTOR)

  1. C174233E40
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E76-7 (CANH) - E76-18 (CANL)
    Ignition switch off
    108 to 132 Ω



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 2 CAN JUNCTION CONNECTOR - NO. 9 JUNCTION CONNECTOR)
OK

REPAIR OR REPLACE NO. 9 JUNCTION CONNECTOR

18. CHECK FOR SHORT IN CAN BUS WIRES (NO. 10 JUNCTION CONNECTOR SIDE)

  1. C174933E01
    Disconnect the E70 No. 10 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E3-16 (CANP) - E3-15 (CANN)
    Ignition switch off
    108 to 132 Ω
    E3-16 (CANP) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E3-15 (CANN) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E3-16 (CANP) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E3-15 (CANN) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
Go to step 20
OK


19. CHECK FOR SHORT IN CAN BUS WIRES (NO. 10 JUNCTION CONNECTOR - COMBINATION METER)

  1. C175844E01
    Measure the resistance according to the value(s) in the table below.
    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    E70-3 (CANH) - E70-14 (CANN)
    Ignition switch off
    1 Ω or higher
    OK
    E70-3 (CANH) - E70-14 (CANL)
    Ignition switch off
    Below 1 Ω
    NG
    E70-3 (CANH) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    E70-14 (CANL) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    E70-3 (CANH) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    E70-14 (CANL) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    E70-3 (CANH) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    E70-14 (CANL) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    E70-3 (CANH) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG
    E70-14 (CANL) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG



NG
Go to step 34
OK

REPAIR OR REPLACE NO. 10 JUNCTION CONNECTOR

20. CONNECT CONNECTOR
  1. Reconnect the E70 No. 10 junction connector connector.


NEXT


21. CHECK FOR SHORT IN CAN BUS WIRES (NO. 10 JUNCTION CONNECTOR - NO. 9 JUNCTION CONNECTOR)

  1. C175844E08
    Disconnect the E76 No. 9 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E76-1 (CANH) - E76-12 (CANL)
    Ignition switch off
    108 to 132 Ω
    E76-1 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E76-12 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E76-1 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E76-12 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 10 JUNCTION CONNECTOR - NO. 9 JUNCTION CONNECTOR)
OK


22. CHECK FOR SHORT IN CAN BUS WIRES (NO. 9 JUNCTION CONNECTOR SIDE)

  1. C174933E01
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E3-16 (CANP) - E3-15 (CANN)
    Ignition switch off
    108 to 132 Ω
    E3-16 (CANP) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E3-15 (CANN) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E3-16 (CANP) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E3-15 (CANN) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
Go to step 27
OK


23. CHECK FOR SHORT IN CAN BUS WIRES (NO. 9 JUNCTION CONNECTOR - POSITION CONTROL AND SWITCH)

NOTICE:
For vehicles without the seat memory, go to "Check for Short in CAN Bus Wires (No. 9 Junction Connector - Multiplex Tilt and Telescopic ECU)".

  1. C175835E06
    Measure the resistance according to the value(s) in the table below.
    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    E76-4 (CANH) - E76-15 (CANL)
    Ignition switch off
    1 Ω or higher
    OK
    E76-4 (CANH) - E76-15 (CANL)
    Ignition switch off
    Below 1 Ω
    NG
    E76-4 (CANH) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    E76-15 (CANL) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    E76-4 (CANH) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    E76-15 (CANL) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    E76-4 (CANH) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    E76-15 (CANL) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    E76-4 (CANH) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG
    E76-15 (CANL) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG



NG
Go to step 36
OK


24. CHECK FOR SHORT IN CAN BUS WIRES (NO. 9 JUNCTION CONNECTOR - MULTIPLEX TILT AND TELESCOPIC ECU)

NOTICE:
For vehicles without the power tilt and telescopic steering column system, go to "Check for Short in CAN Bus Wires (No. 9 Junction Connector - Outer Mirror Control ECU)".

  1. C175835E07
    Measure the resistance according to the value(s) in the table below.
    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    E76-3 (CANH) - E76-14 (CANL)
    Ignition switch off
    1 Ω or higher
    OK
    E76-3 (CANH) - E76-14 (CANL)
    Ignition switch off
    Below 1 Ω
    NG
    E76-3 (CANH) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    E76-14 (CANL) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    E76-3 (CANH) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    E76-14 (CANL) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    E76-3 (CANH) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    E76-14 (CANL) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    E76-3 (CANH) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG
    E76-14 (CANL) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG



NG
Go to step 38
OK


25. CHECK FOR SHORT IN CAN BUS WIRES (NO. 9 JUNCTION CONNECTOR - OUTER MIRROR CONTROL ECU)

NOTICE:
For vehicles without the seat memory, go to "Check for Short in CAN Bus Wires (No. 9 Junction Connector - Certification ECU)".

  1. C175835E08
    Measure the resistance according to the value(s) in the table below.
    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    E76-5 (CANH) - E76-16 (CANL)
    Ignition switch off
    1 Ω or higher
    OK
    E76-5 (CANH) - E76-16 (CANL)
    Ignition switch off
    Below 1 Ω
    NG
    E76-5 (CANH) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    E76-16 (CANL) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    E76-5 (CANH) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    E76-16 (CANL) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    E76-5 (CANH) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    E76-16 (CANL) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    E76-5 (CANH) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG
    E76-16 (CANL) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG



NG
Go to step 40
OK


26. CHECK FOR SHORT IN CAN BUS WIRES (NO. 9 JUNCTION CONNECTOR - CERTIFICATION ECU)

NOTICE:
For vehicles without the entry and start system, repair or replace No. 9 junction connector.

  1. C175835E09
    Measure the resistance according to the value(s) in the table below.
    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    E76-2 (CANH) - E76-13 (CANL)
    Ignition switch off
    1 Ω or higher
    OK
    E76-2 (CANH) - E76-13 (CANL)
    Ignition switch off
    Below 1 Ω
    NG
    E76-2 (CANH) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    E76-13 (CANL) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    E76-2 (CANH) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    E76-13 (CANL) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    E76-2 (CANH) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    E76-13 (CANL) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    E76-2 (CANH) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG
    E76-13 (CANL) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG



NG
Go to step 42
OK

REPAIR OR REPLACE NO. 9 JUNCTION CONNECTOR

27. CONNECT CONNECTOR
  1. Reconnect the E76 No. 9 junction connector connector.


NEXT


28. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION CONNECTOR - NO. 9 JUNCTION CONNECTOR)

  1. C175841E04
    Disconnect the L30 No. 2 CAN junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    L30-1 (CANH) - L30-2 (CANL)
    Ignition switch off
    108 to 132 Ω
    L30-1 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    L30-2 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    L30-1 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    L30-2 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 2 CAN JUNCTION CONNECTOR - NO. 9 JUNCTION CONNECTOR)
OK


29. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION CONNECTOR SIDE)

  1. C174933E01
    Disconnect the L29 No. 2 CAN junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E3-16 (CANP) - E3-15 (CANN)
    Ignition switch off
    108 to 132 Ω
    E3-16 (CANP) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E3-15 (CANN) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E3-16 (CANP) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E3-15 (CANN) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
Go to step 30
OK

REPAIR OR REPLACE NO. 2 CAN JUNCTION CONNECTOR

30. CONNECT CONNECTOR
  1. Reconnect the L29 and L30 No. 2 CAN junction connector connectors.


NEXT


31. CHECK FOR SHORT IN CAN BUS WIRES (NO. 8 JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)

  1. C175835E12
    Disconnect the E73 No. 8 junction connector connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E73-1 (CANH) - E73-12 (CANL)
    Ignition switch off
    108 to 132 Ω
    E73-1 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E73-12 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E73-1 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E73-12 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 8 JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)
OK


32. CHECK FOR SHORT IN CAN BUS WIRES (NO. 8 JUNCTION CONNECTOR - WINDSHIELD WIPER ECU)

NOTICE:
For vehicles without the rain sensor, go to "Check for Short in CAN Bus Wires (No. 8 Junction Connector - Main Body ECU)".

  1. C175835E10
    Measure the resistance according to the value(s) in the table below.
    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    E73-4 (CANH) - E73-15 (CANN)
    Ignition switch off
    1 Ω or higher
    OK
    E73-4 (CANH) - E73-15 (CANN)
    Ignition switch off
    Below 1 Ω
    NG
    E73-4 (CANH) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    E73-15 (CANL) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    E73-4 (CANH) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    E73-15 (CANL) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    E73-4 (CANH) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    E73-15 (CANL) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    E73-4 (CANH) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG
    E73-15 (CANL) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG



NG
Go to step 44
OK


33. CHECK FOR SHORT IN CAN BUS WIRES (NO. 8 JUNCTION CONNECTOR - MAIN BODY ECU)

  1. C175835E11
    Measure the resistance according to the value(s) in the table below.
    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    E73-3 (CANH) - E73-14 (CANL)
    Ignition switch off
    1 Ω or higher
    OK
    E73-3 (CANH) - E73-14 (CANL)
    Ignition switch off
    Below 1 Ω
    NG
    E73-3 (CANH) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    E73-14 (CANL) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    E73-3 (CANH) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    E73-14 (CANL) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    E73-3 (CANH) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    E73-14 (CANL) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    E73-3 (CANH) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG
    E73-14 (CANL) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG



NG
Go to step 46
OK

REPAIR OR REPLACE NO. 8 JUNCTION CONNECTOR

34. CONNECT CONNECTOR
  1. Reconnect the E70 No. 10 junction connector connector.


NEXT


35. CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER)

  1. C176288E01
    Measure the resistance according to the value(s) in the table below.
    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Result
    Type
    Proceed to
    E7-1 (MPX+) - E7-2 (MPX-)
    Ignition switch off
    1 Ω or higher
    OK
    w/ Multi-information Display
    A
    w/o Multi-information Display
    B
    E7-1 (MPX+) - E7-2 (MPX-)
    Ignition switch off
    Below 1 Ω
    NG
    All types
    C
    E7-1 (MPX+) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    w/ Multi-information Display
    A
    w/o Multi-information Display
    B
    E7-2 (MPX-) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    w/ Multi-information Display
    A
    w/o Multi-information Display
    B
    E7-1 (MPX+) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    All types
    C
    E7-2 (MPX-) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    All types
    C
    E7-1 (MPX+) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    w/ Multi-information Display
    A
    w/o Multi-information Display
    B
    E7-2 (MPX-) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    w/ Multi-information Display
    A
    w/o Multi-information Display
    B
    E7-1 (MPX+) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG
    All types
    C
    E7-2 (MPX-) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG
    All types
    C



B
REPLACE COMBINATION METER ASSEMBLY (Click here)

C
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER (NO. 10 JUNCTION CONNECTOR - COMBINATION METER)
A

REPLACE COMBINATION METER ASSEMBLY (Click here)

36. CONNECT CONNECTOR
  1. Reconnect the E76 No. 9 junction connector connector.


NEXT


37. CHECK FOR SHORT IN CAN BUS WIRES (POSITION CONTROL ECU AND SWITCH)

  1. C175837E02
    Disconnect the c27 position control ECU and switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    c27-5 (MPX1) - c27-1 (MPX2)
    Ignition switch off
    1 Ω or higher
    OK
    c27-5 (MPX1) - c27-1 (MPX2)
    Ignition switch off
    Below 1 Ω
    NG
    c27-5 (MPX1) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    c27-1 (MPX2) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    c27-5 (MPX1) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    c27-1 (MPX2) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    c27-5 (MPX1) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    c27-1 (MPX2) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    c27-5 (MPX1) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG
    c27-1 (MPX2) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO POSITION CONTROL ECU AND SWITCH (MPX1, MPX2)
OK

REPLACE POSITION CONTROL ECU AND SWITCH ASSEMBLY (Click here)

38. CONNECT CONNECTOR
  1. Reconnect the E76 No. 9 junction connector connector.


NEXT


39. CHECK FOR SHORT IN CAN BUS WIRES (MULTIPLEX TILT AND TELESCOPIC ECU)

  1. C175838E01
    Disconnect the E27 power tilt and telescopic ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    E27-5 (CANP) - E27-14 (CANN)
    Ignition switch off
    1 Ω or higher
    OK
    E27-5 (CANP) - E27-14 (CANN)
    Ignition switch off
    Below 1 Ω
    NG
    E27-5 (CANP) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    E27-14 (CANN) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    E27-5 (CANP) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    E27-14 (CANN) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    E27-5 (CANP) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    E27-14 (CANN) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    E27-5 (CANP) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG
    E27-14 (CANN) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO POWER TILT AND TELESCOPIC ECU (CANP, CANN)
OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU (Click here)

40. CONNECT CONNECTOR
  1. Reconnect the E76 No. 9 junction connector connector.


NEXT


41. CHECK FOR SHORT IN CAN BUS WIRES (OUTER MIRROR CONTROL ECU)

  1. C175839E02
    Disconnect the I24 outer mirror control ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    I24-1 (CANH) - I24-21 (CANL)
    Ignition switch off
    1 Ω or higher
    OK
    I24-1 (CANH) - I24-21 (CANL)
    Ignition switch off
    Below 1 Ω
    NG
    I24-1 (CANH) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    I24-21 (CANL) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    I24-1 (CANH) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    I24-21 (CANL) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    I24-1 (CANH) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    I24-21 (CANL) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    I24-1 (CANH) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG
    I24-21 (CANL) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO OUTER MIRROR CONTROL ECU (CANH, CANL)
OK

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (Click here)

42. CONNECT CONNECTOR
  1. Reconnect the E76 No. 9 junction connector connector.


NEXT


43. CHECK FOR SHORT IN CAN BUS WIRES (CERTIFICATION ECU)

  1. C175836E01
    Disconnect the E29 certification ECU (smart key ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    E29-27 (CANH) - E29-28 (CANL)
    Ignition switch off
    1 Ω or higher
    OK
    E29-27 (CANH) - E29-28 (CANL)
    Ignition switch off
    Below 1 Ω
    NG
    E29-27 (CANH) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    E29-28 (CANL) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    E29-27 (CANH) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    E29-28 (CANL) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    E29-27 (CANH) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    E29-28 (CANL) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    E29-27 (CANH) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG
    E29-28 (CANL) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CERTIFICATION ECU (SMART KEY ECU ASSEMBLY) (CANH, CANL)
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

44. CONNECT CONNECTOR
  1. Reconnect the E73 No. 8 junction connector connector.


NEXT


45. CHECK FOR SHORT IN CAN BUS WIRES (WINDSHIELD WIPER ECU)

  1. C176954E02
    Disconnect the E85 windshield wiper ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    E85-6 (CANH) - E85-5 (CANL)
    Ignition switch off
    1 Ω or higher
    OK
    E85-6 (CANH) - E85-5 (CANL)
    Ignition switch off
    Below 1 Ω
    NG
    E85-6 (CANH) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    E85-5 (CANL) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    E85-6 (CANH) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    E85-5 (CANL) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    E85-6 (CANH) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    E85-5 (CANL) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    E85-6 (CANH) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG
    E85-5 (CANL) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO WINDSHIELD WIPER ECU (CANH, CANL)
OK

REPLACE WINDSHIELD WIPER ECU (Click here)

46. CONNECT CONNECTOR
  1. Reconnect the E73 No. 8 junction connector connector.


NEXT


47. CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU)

  1. C175840E01
    Disconnect the E3 main body ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Result 
    Tester Connection
    Switch Condition
    Measured Resistance
    Proceed to
    E3-16 (CANP) - E3-15 (CANN)
    Ignition switch off
    1 Ω or higher
    OK
    E3-16 (CANP) - E3-15 (CANN)
    Ignition switch off
    Below 1 Ω
    NG
    E3-16 (CANP) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    E3-15 (CANN) - E22-4 (CG)
    Ignition switch off
    1 Ω or higher
    OK
    E3-16 (CANP) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    E3-15 (CANN) - E22-4 (CG)
    Ignition switch off
    Below 1 Ω
    NG
    E3-16 (CANP) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    E3-15 (CANN) - E22-16 (BAT)
    Ignition switch off
    1 Ω or higher
    OK
    E3-16 (CANP) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG
    E3-15 (CANN) - E22-16 (BAT)
    Ignition switch off
    Below 1 Ω
    NG



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO MAIN BODY ECU (NO. 8 JUNCTION CONNECTOR - MAIN BODY ECU)
OK

REPLACE MAIN BODY ECU

48. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY AND BODY GROUND)
  1. Connect the cable to the negative (-) battery terminal.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Disconnect the 2A, 2D and E3 main body ECU (cowl side junction block LH) connectors.C176067E01

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2D-62 (GND2) - Body ground
    Always
    Below 1 Ω
    E3-1 (GND3) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    2A-1 (ALTB) - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)


← U0327 Software Incompatibility with Vehicle Security Control Module (from Jan 2012)U1002 (CAN MS BUS) Lost Communication with Gateway Module (Main body ECU) (from Jan 2012) →