2011-2013 Land Cruiser · Service Manual Power Source / Network

U1002 (CAN MS BUS) Lost Communication with Gateway Module (Main body ECU)

Diagnostic trouble codes · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

  1. The main body ECU stores this DTC when no signals can be received from the ECUs that have been memorized as those connected to the CAN MS bus.
  2. When the main body ECU receives a response signal from the ECUs connected to the CAN MS bus, the main body ECU recognizes and memorizes that the ECU is connected to the CAN MS bus. Based on this memorized data, the main body ECU monitors for malfunctions in the ECUs connected to the CAN MS bus when communicating with those ECUs. If the main body ECU cannot receive response signals from the ECUs that have been memorized as those connected to the CAN MS bus, the main body ECU determines that a malfunction exists.
  3. If 2 or more DTCs are output during the DTC check, one side of the CAN branch wire may be open (one side of the CANH [CAN branch wire]/CANL [CAN branch wire] of the ECU and/or sensor is open).
DTC Code
DTC Detection Condition
Trouble Area
U1002 (CAN MS BUS)
Lost communication with the gateway module (main body ECU).
  1. MS bus circuit
  2. Windshield wiper ECU CAN branch wire or connector*1
  3. Position control ECU and switch CAN branch wire or connector*2
  4. Outer mirror control ECU assembly CAN branch wire or connector*2
  5. Multiplex tilt and telescopic ECU branch wire or connector*3
  6. Certification ECU (smart key ECU assembly) CAN branch wire or connector*4
  7. Power back door unit assembly (power back door ECU) CAN branch wire or connector*5
  8. No. 2 main body ECU CAN branch wire or connector*5
  9. Main body ECU (cowl side junction block LH) CAN main wire or connector
  10. Combination meter assembly CAN main wire or connector
  11. Windshield wiper ECU*1
  12. Position control ECU and switch*2
  13. Outer mirror control ECU assembly*2
  14. Multiplex tilt and telescopic ECU*3
  15. Certification ECU (smart key ECU assembly)*4
  16. Power back door unit assembly (power back door ECU)*5
  17. No. 2 main body ECU*5
  18. Main body ECU (cowl side junction block LH)
  19. Combination meter assembly
  20. No. 8 junction connector
  21. No. 9 junction connector
  22. No. 10 junction connector
  23. No. 2 CAN junction connector
  1. *1: w/ Rain Sensor
  2. *2: w/ Seat Memory
  3. *3: w/ Power Tilt Power Telescopic Steering Column System
  4. *4: w/ Entry and Start System
  5. *5: w/ Power Back Door System

WIRING DIAGRAM

C260847E01
C260848E01

INSPECTION PROCEDURE

HINT:
Operating the ignition switch, any switches or any doors triggers related ECU and sensor communication with the CAN, which causes resistance variation.


1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).


NEXT


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL
  1. Disconnect the cable from the negative (-) battery terminal before measuring the resistances of the CAN main wire and the CAN branch wire.

    CAUTION:
    For vehicles with an SRS system:
    Wait at least 90 seconds after disconnecting the cable from the negative (-) battery terminal to disable the SRS system.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


NEXT


3. CHECK CAN BUS WIRE (CAN MAIN WIRE FOR DISCONNECTION, CHECK BUS LINE FOR SHORT CIRCUIT)

  1. C259508E01
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    Resistance Malfunction
    E3-16 (CANP) - E3-15 (CANN)
    Ignition switch off
    54 to 69 Ω
    Below 53 Ω: Short in line
    E3-16 (CANP) - E3-15 (CANN)
    Ignition switch off
    54 to 69 Ω
    70 Ω or higher: Open in CAN main bus line
    E3-16 (CANP) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    Below 6 kΩ: +B short
    E3-15 (CANN) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    Below 6 kΩ: +B short
    E3-16 (CANP) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    Below 200 Ω: Ground short
    E3-15 (CANN) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    Below 200 Ω: Ground short

    Text in Illustration 
    *a
    Component with harness connected
    (Main Body ECU [Cowl Side Junction Block LH])
    *b
    Front view of DLC3
    Result 
    Result
    Proceed to
    NG
    1. Open in CAN main wire
    A
    NG
    1. Short in line
    2. +B short
    3. Ground short
    B
    OK
    C



B
Go to step 19

C
Go to step 55
A


4. CHECK FOR OPEN IN MAIN BUS WIRE (NO. 2 CAN JUNCTION CONNECTOR - MAIN BODY ECU)

  1. C259621E01
    Disconnect the L29 No. 2 CAN junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    L29-1 (CANH) - L29-2 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 CAN Junction Connector)



NG
Go to step 6
OK


5. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 2 CAN JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)

  1. C259621E02
    Disconnect the L30 No. 2 CAN junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    L30-1 (CANH) - L30-2 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 CAN Junction Connector)



NG
Go to step 11
OK

REPLACE NO. 2 CAN JUNCTION CONNECTOR

6. CONNECT CONNECTOR
  1. Reconnect the L29 No. 2 CAN junction connector.


NEXT


7. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 8 JUNCTION CONNECTOR - MAIN BODY ECU)

  1. E211920E21
    Disconnect the E73 No. 8 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E73-3 (CANH) - E73-14 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 8 Junction Connector)



NG
Go to step 9
OK


8. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 8 JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)

  1. E211920E11
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E73-1 (CANH) - E73-12 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 8 Junction Connector)



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 8 JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)
OK

REPLACE NO. 8 JUNCTION CONNECTOR

9. CONNECT CONNECTOR
  1. Reconnect the E73 No. 8 junction connector.


NEXT


10. CHECK FOR OPEN IN CAN BUS MAIN WIRE (MAIN BODY ECU - NO. 8 JUNCTION CONNECTOR)

  1. E211922E02
    Disconnect the E3 main body ECU (cowl side junction block LH) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E3-16 (CANP) - E3-15 (CANN)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Main Body ECU [Cowl Side Junction Block LH])



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO MAIN BODY ECU (MAIN BODY ECU - NO. 8 JUNCTION CONNECTOR)
OK

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)

11. CONNECT CONNECTOR
  1. Reconnect the L29 and L30 No. 2 CAN junction connectors.


NEXT


12. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 10 JUNCTION CONNECTOR - NO. 9 JUNCTION CONNECTOR)

  1. E211920E09
    Disconnect the E70 No. 10 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E70-1 (CANH) - E70-12 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 10 Junction Connector)



NG
Go to step 16
OK


13. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 10 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)

  1. E211920E10
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E70-3 (CANH) - E70-14 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 10 Junction Connector)



NG
Go to step 14
OK

REPLACE NO. 10 JUNCTION CONNECTOR

14. CONNECT CONNECTOR
  1. Reconnect the E70 No. 10 junction connector.


NEXT


15. CHECK FOR OPEN IN CAN BUS MAIN WIRE (COMBINATION METER ASSEMBLY - NO. 10 JUNCTION CONNECTOR)

  1. E211921E02
    Disconnect the E7 combination meter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E7-1 (MPX+) - E7-2 (MPX-)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Combination Meter Assembly)
    Result 
    Result
    Proceed to
    OK (w/ Multi-information Display)
    A
    OK (w/o Multi-information Display)
    B
    NG
    C



B
REPLACE COMBINATION METER ASSEMBLY (Click here)

C
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ASSEMBLY (COMBINATION METER ASSEMBLY - NO. 10 JUNCTION CONNECTOR)
A

REPLACE COMBINATION METER ASSEMBLY (Click here)

16. CONNECT CONNECTOR
  1. Reconnect the E70 No. 10 junction connector.


NEXT


17. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 9 JUNCTION CONNECTOR - NO. 10 JUNCTION CONNECTOR)

  1. E211920E08
    Disconnect the E76 No. 9 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E76-1 (CANH) - E76-12 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 9 Junction Connector)



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 9 JUNCTION CONNECTOR - NO. 10 JUNCTION CONNECTOR)
OK


18. CHECK FOR OPEN IN CAN BUS MAIN WIRE (NO. 9 JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)

  1. E211920E22
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E76-7 (CANH) - E76-18 (CANL)
    Ignition switch off
    108 to 132 Ω

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 9 Junction Connector)



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 9 JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)
OK

REPLACE NO. 9 JUNCTION CONNECTOR

19. CHECK FOR SHORT IN CAN BUS WIRES (NO. 10 JUNCTION CONNECTOR SIDE)

  1. C259508E01
    Disconnect the E70 No. 10 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E3-16 (CANP) - E3-15 (CANN)
    Ignition switch off
    108 to 132 Ω
    E3-16 (CANP) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E3-15 (CANN) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E3-16 (CANP) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E3-15 (CANN) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Component with harness connected
    (Main Body ECU [Cowl Side Junction Block LH])
    *b
    Front view of DLC3



NG
Go to step 21
OK


20. CHECK FOR SHORT IN CAN BUS WIRES (NO. 10 JUNCTION CONNECTOR - COMBINATION METER ASSEMBLY)

  1. C259545E29
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E70-3 (CANH) - E70-14 (CANN)
    Ignition switch off
    108 to 132 Ω
    E70-3 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E70-14 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E70-3 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E70-14 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 10 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 37
OK

REPLACE NO. 10 JUNCTION CONNECTOR

21. CONNECT CONNECTOR
  1. Reconnect the E70 No. 10 junction connector.


NEXT


22. CHECK FOR SHORT IN CAN BUS WIRES (NO. 9 JUNCTION CONNECTOR - NO. 10 JUNCTION CONNECTOR)

  1. C259545E33
    Disconnect the E76 No. 9 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E76-1 (CANH) - E76-12 (CANL)
    Ignition switch off
    108 to 132 Ω
    E76-1 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E76-12 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E76-1 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E76-12 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 9 Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 9 JUNCTION CONNECTOR - NO. 10 JUNCTION CONNECTOR)
OK


23. CHECK FOR SHORT IN CAN BUS WIRES (NO. 9 JUNCTION CONNECTOR SIDE)

  1. C259508E01
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E3-16 (CANP) - E3-15 (CANN)
    Ignition switch off
    108 to 132 Ω
    E3-16 (CANP) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E3-15 (CANN) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E3-16 (CANP) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E3-15 (CANN) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Component with harness connected
    (Main Body ECU [Cowl Side Junction Block LH])
    *b
    Front view of DLC3



NG
Go to step 28
OK


24. CHECK FOR SHORT IN CAN BUS WIRES (NO. 9 JUNCTION CONNECTOR - POSITION CONTROL ECU AND SWITCH)

NOTICE:
For vehicles without seat memory, go to "Check for Short in CAN Bus Wires (No. 9 Junction Connector - Multiplex Tilt and Telescopic ECU)".

  1. C259545E35
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E76-4 (CANH) - E76-15 (CANL)
    Ignition switch off
    200 Ω or higher
    E76-4 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E76-15 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E76-4 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E76-15 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

Text in Illustration 
*a
Rear view of wire harness connector
(to No. 9 Junction Connector)
*b
Front view of DLC3


NG
Go to step 39
OK


25. CHECK FOR SHORT IN CAN BUS WIRES (NO. 9 JUNCTION CONNECTOR - MULTIPLEX TILT AND TELESCOPIC ECU)

NOTICE:
For vehicles without a power tilt and power telescopic steering column system, go to "Check for Short in CAN Bus Wires (No. 9 Junction Connector - Outer Mirror Control ECU Assembly)".

  1. C259545E37
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E76-3 (CANH) - E76-14 (CANL)
    Ignition switch off
    200 Ω or higher
    E76-3 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E76-14 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E76-3 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E76-14 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

Text in Illustration 
*a
Rear view of wire harness connector
(to No. 9 Junction Connector)
*b
Front view of DLC3


NG
Go to step 41
OK


26. CHECK FOR SHORT IN CAN BUS WIRES (NO. 9 JUNCTION CONNECTOR - OUTER MIRROR CONTROL ECU ASSEMBLY)

NOTICE:
For vehicles without seat memory, go to "Check for Short in CAN Bus Wires (No. 9 Junction Connector - Certification ECU)".

  1. C259545E36
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E76-5 (CANH) - E76-16 (CANL)
    Ignition switch off
    200 Ω or higher
    E76-5 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E76-16 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E76-5 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E76-16 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 9 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 43
OK


27. CHECK FOR SHORT IN CAN BUS WIRES (NO. 9 JUNCTION CONNECTOR - CERTIFICATION ECU)

NOTICE:
For vehicles without an entry and start system, replace No. 9 junction connector.

  1. C259545E34
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E76-2 (CANH) - E76-13 (CANL)
    Ignition switch off
    200 Ω or higher
    E76-2 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E76-13 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E76-2 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E76-13 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 9 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 45
OK

REPLACE NO. 9 JUNCTION CONNECTOR

28. CONNECT CONNECTOR
  1. Reconnect the E76 No. 9 junction connector.


NEXT


29. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION CONNECTOR - NO. 9 JUNCTION CONNECTOR)

  1. C259622E01
    Disconnect the L30 No. 2 CAN junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    L30-1 (CANH) - L30-2 (CANL)
    Ignition switch off
    108 to 132 Ω
    L30-1 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    L30-2 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    L30-1 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    L30-2 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 CAN Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 2 CAN JUNCTION CONNECTOR - NO. 9 JUNCTION CONNECTOR)
OK


30. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION CONNECTOR SIDE)

  1. C259508E01
    Disconnect the L29 No. 2 CAN junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E3-16 (CANP) - E3-15 (CANN)
    Ignition switch off
    108 to 132 Ω
    E3-16 (CANP) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E3-15 (CANN) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E3-16 (CANP) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E3-15 (CANN) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Component with harness connected
    (Main Body ECU [Cowl Side Junction Block LH])
    *b
    Front view of DLC3
    Result 
    Result
    Proceed to
    OK (w/o Power Back Door System)
    A
    OK (w/ Power Back Door System)
    B
    NG
    C



B
Go to step 31

C
Go to step 33
A

REPLACE NO. 2 CAN JUNCTION CONNECTOR

31. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION CONNECTOR - POWER BACK DOOR ECU)

  1. C259622E02
    Disconnect the L54 No. 2 CAN junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    L54-1 (CANH) - L54-2 (CANL)
    Ignition switch off
    200 Ω or higher
    L54-1 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    L54-2 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    L54-1 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    L54-2 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 CAN Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 47
OK


32. CHECK FOR FOR SHORT IN CAN BUS WIRES (NO. 2 CAN JUNCTION CONNECTOR - NO. 2 MAIN BODY ECU)

  1. C259622E04
    Disconnect the L57 No. 2 CAN junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    L57-1 (CANH) - L57-2 (CANL)
    Ignition switch off
    200 Ω or higher
    L57-1 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    L57-2 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    L57-1 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    L57-2 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 CAN Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 49
OK

REPLACE NO. 2 CAN JUNCTION CONNECTOR

33. CONNECT CONNECTOR
  1. Reconnect the L29 and L30 No. 2 CAN junction connectors.


NEXT


34. CHECK FOR SHORT IN CAN BUS WIRES (NO. 8 JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)

  1. C259545E30
    Disconnect the E73 No. 8 junction connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E73-1 (CANH) - E73-12 (CANL)
    Ignition switch off
    108 to 132 Ω
    E73-1 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E73-12 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E73-1 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E73-12 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 8 Junction Connector)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE OR CONNECTOR (NO. 8 JUNCTION CONNECTOR - NO. 2 CAN JUNCTION CONNECTOR)
OK


35. CHECK FOR SHORT IN CAN BUS WIRES (NO. 8 JUNCTION CONNECTOR - WINDSHIELD WIPER ECU)

NOTICE:
For vehicles without an rain sensor, go to "Check for Short in CAN Bus Wires (No. 8 Junction Connector - Main Body ECU)".

  1. C259545E31
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E73-4 (CANH) - E73-15 (CANL)
    Ignition switch off
    200 Ω or higher
    E73-4 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E73-15 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E73-4 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E73-15 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 8 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 51
OK


36. CHECK FOR SHORT IN CAN BUS WIRES (NO. 8 JUNCTION CONNECTOR - MAIN BODY ECU)

  1. C259545E32
    Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E73-3 (CANH) - E73-14 (CANL)
    Ignition switch off
    108 to 132 Ω
    E73-3 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E73-14 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E73-3 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E73-14 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 8 Junction Connector)
    *b
    Front view of DLC3



NG
Go to step 53
OK

REPLACE NO. 8 JUNCTION CONNECTOR

37. CONNECT CONNECTOR
  1. Reconnect the E70 No. 10 junction connector.


NEXT


38. CHECK FOR SHORT IN CAN BUS WIRES (COMBINATION METER ASSEMBLY)

  1. C259509E01
    Disconnect the E7 combination meter assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E7-1 (MPX+) - E7-2 (MPX-)
    Ignition switch off
    108 to 132 Ω
    E7-1 (MPX+) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E7-2 (MPX-) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E7-1 (MPX+) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E7-2 (MPX-) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Combination Meter Assembly)
    *b
    Front view of DLC3
    Result 
    Result
    Proceed to
    OK (w/ Multi-information Display)
    A
    OK (w/o Multi-information Display)
    B
    NG
    C



B
REPLACE COMBINATION METER ASSEMBLY (Click here)

C
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO COMBINATION METER ASSEMBLY (MPX+, MPX-)
A

REPLACE COMBINATION METER ASSEMBLY (Click here)

39. CONNECT CONNECTOR
  1. Reconnect the E76 No. 9 junction connector.


NEXT


40. CHECK FOR SHORT IN CAN BUS WIRES (POSITION CONTROL ECU AND SWITCH)

  1. C259513E02
    Disconnect the c27 position control ECU and switch connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    c27-5 (MPX1) - c27-1 (MPX2)
    Ignition switch off
    54 to 69 Ω
    c27-5 (MPX1) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    c27-1 (MPX2) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    c27-5 (MPX1) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    c27-1 (MPX2) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Position Control ECU and Switch)
    *b
    Front view of DLC3



NG
REPLACE CAN BRANCH WIRE CONNECTED TO POSITION CONTROL ECU AND SWITCH (MPX1, MPX2)
OK

REPLACE POSITION CONTROL ECU AND SWITCH (Click here)

41. CONNECT CONNECTOR
  1. Reconnect the E76 No. 9 junction connector.


NEXT


42. CHECK FOR SHORT IN CAN BUS WIRES (MULTIPLEX TILT AND TELESCOPIC ECU)

  1. C259515E01
    Disconnect the E27 multiplex tilt and telescopic ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E27-5 (CANP) - E27-14 (CANN)
    Ignition switch off
    54 to 69 Ω
    E27-5 (CANP) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E27-14 (CANN) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E27-5 (CANP) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E27-14 (CANN) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Multiplex Tilt and Telescopic ECU)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO MULTIPLEX TILT AND TELESCOPIC ECU (CANP, CANN)
OK

REPLACE MULTIPLEX TILT AND TELESCOPIC ECU (Click here)

43. CONNECT CONNECTOR
  1. Reconnect the E76 No. 9 junction connector.


NEXT


44. CHECK FOR SHORT IN CAN BUS WIRES (OUTER MIRROR CONTROL ECU ASSEMBLY)

  1. C259514E03
    Disconnect the I24 outer mirror control ECU assembly connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    I24-1 (CANH) - I24-21 (CANL)
    Ignition switch off
    54 to 69 Ω
    I24-1 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    I24-21 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    I24-1 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    I24-21 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Outer Mirror Control ECU Assembly)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO OUTER MIRROR CONTROL ECU ASSEMBLY (CANH, CANL)
OK

REPLACE OUTER MIRROR CONTROL ECU ASSEMBLY (Click here)

45. CONNECT CONNECTOR
  1. Reconnect the E76 No. 9 junction connector.


NEXT


46. CHECK FOR SHORT IN CAN BUS WIRES (CERTIFICATION ECU)

  1. C259512E01
    Disconnect the E29 certification ECU (smart key ECU assembly) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E29-27 (CANH) - E29-28 (CANL)
    Ignition switch off
    54 to 69 Ω
    E29-27 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E29-28 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E29-27 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E29-28 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Certification ECU [Smart Key ECU Assembly])
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO CERTIFICATION ECU (CANH, CANL)
OK

REPLACE CERTIFICATION ECU (SMART KEY ECU ASSEMBLY)

47. CONNECT CONNECTOR
  1. Reconnect the L29, L30 and L54 No. 2 CAN junction connectors.


NEXT


48. CHECK FOR SHORT IN CAN BUS WIRES (POWER BACK DOOR ECU)

  1. C217226E10
    Disconnect the L52 power back door unit assembly (power back door ECU) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    L52-6 (MPX1) - L52-5 (MPX2)
    Ignition switch off
    54 to 69 Ω
    L52-6 (MPX1) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    L52-5 (MPX2) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    L52-6 (MPX1) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    L52-5 (MPX2) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Power Back Door Unit Assembly [Power Back Door ECU])
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO POWER BACK DOOR ECU (MPX1, MPX2)
OK

REPLACE POWER BACK DOOR UNIT ASSEMBLY (POWER BACK DOOR ECU) (Click here)

49. CONNECT CONNECTOR
  1. Reconnect the L29, L30, L54 and L57 No. 2 CAN junction connectors.


NEXT


50. CHECK FOR SHORT IN CAN BUS WIRES (NO. 2 MAIN BODY ECU)

  1. C217226E12
    Disconnect the L50 No. 2 main body ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    L50-11 (MPX+) - L50-12 (MPX-)
    Ignition switch off
    54 to 69 Ω
    L50-11 (MPX+) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    L50-12 (MPX-) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    L50-11 (MPX+) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    L50-12 (MPX-) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to No. 2 Main Body ECU)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO NO. 2 MAIN BODY ECU (MPX+, MPX-)
OK

REPLACE NO. 2 MAIN BODY ECU (Click here)

51. CONNECT CONNECTOR
  1. Reconnect the E73 No. 8 junction connector.


NEXT


52. CHECK FOR SHORT IN CAN BUS WIRES (WINDSHIELD WIPER ECU)

  1. C259510E01
    Disconnect the E85 windshield wiper ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E85-6 (CANH) - E85-5 (CANL)
    Ignition switch off
    54 to 69 Ω
    E85-6 (CANH) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E85-5 (CANL) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E85-6 (CANH) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E85-5 (CANL) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Windshield Wiper ECU)
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN BRANCH WIRE CONNECTED TO WINDSHIELD WIPER ECU (CANH, CANL)
OK

REPLACE WINDSHIELD WIPER ECU (Click here)

53. CONNECT CONNECTOR
  1. Reconnect the E73 No. 8 junction connector.


NEXT


54. CHECK FOR SHORT IN CAN BUS WIRES (MAIN BODY ECU)

  1. C259516E01
    Disconnect the E3 main body ECU (cowl side junction block LH) connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    E3-16 (CANP) - E3-15 (CANN)
    Ignition switch off
    108 to 132 Ω
    E3-16 (CANP) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E3-15 (CANN) - E22-4 (CG)
    Ignition switch off
    200 Ω or higher
    E3-16 (CANP) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher
    E3-15 (CANN) - E22-16 (BAT)
    Ignition switch off
    6 kΩ or higher

    Text in Illustration 
    *a
    Rear view of wire harness connector
    (to Main Body ECU [Cowl Side Junction Block LH])
    *b
    Front view of DLC3



NG
REPAIR OR REPLACE CAN MAIN WIRE CONNECTED TO MAIN BODY ECU (CANP, CANN)
OK

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)

55. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - BATTERY AND BODY GROUND)

  1. Connect the cable to the negative (-) battery terminal.C259517E01

    Text in Illustration 
    *a
    Front view of wire harness connector
    (to Main Body ECU [Cowl Side Junction Block LH])
    *b
    Rear view of wire harness connector
    (to Main Body ECU [Cowl Side Junction Block LH])

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Disconnect the E3, 2A and 2D main body ECU (cowl side junction block LH) connectors.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    2D-62 (GND2) - Body ground
    Always
    Below 1 Ω
    E3-1 (GND3) - Body ground
    Always
    Below 1 Ω

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    2A-1 (ALTB) - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)


← U1002 (CAN MS BUS) Lost Communication with Gateway Module (Main body ECU) (Sep 2011 – Dec 2011)U1002 (CAN No. 2 BUS) Lost Communication with Gateway Module (Network Gateway ECU) (Sep 2011 – Dec 2011) →