P1251 Turbocharger / Supercharger Overboost Condition (Too High)
Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
DESCRIPTION
- HINT:
- Refer to DTC P0046 (Click here).
- Refer to DTC P00AF (Click here).
| DTC Detection Drive Pattern |
DTC Detection Condition |
Trouble Area |
| Vehicle being driven |
The turbo motor driver detects an overcurrent caused by the DC motor being stuck (1 trip detection logic). |
|
| DTC No. |
Data List |
| P1251 |
|
- VN turbo vane stuck closed malfunction
- Vehicle surge when driving with full load
- Sudden lack of power due to power being limited
WIRING DIAGRAM
Refer to DTC P0046 (Click here).Refer to DTC P00AF (Click here).
INSPECTION PROCEDURE
- HINT:
- Read freeze frame data using the intelligent tester. Freeze frame data records the engine condition when malfunctions are detected. When troubleshooting, freeze frame data can help determine if the vehicle was moving or stationary, if the engine was warmed up or not, and other data from the time the malfunction occurred.
- NOTICE:
- After replacing the ECM, the new ECM needs registration (Click here) and initialization (Click here ).
| 1. CHECK ANY OTHER DTCS OUTPUT (IN ADDITION TO DTC P1251) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine / DTC.
Read the DTCs.
- Result:
Display (DTC Output)
Proceed to
P1251
A
P1251 and other DTCs
B
|
|
||||
| A | |
| 2. INSPECT TURBOCHARGER SUB-ASSEMBLY (for Bank 1 and/or Bank 2) |
![]() ![]() |
Check the motor movement when turning the ignition switch to ON, when starting the engine and then when turning the ignition switch off.
- OK:
- Motor moves as shown in the illustration.
|
|
||||
| OK | |
| 3. CHECK WHETHER DTC OUTPUT RECURS (DTC P1251) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following: Powertrain / Engine / DTC / Clear.
Clear DTCs (Click here).
Turn the ignition switch off.
Start the engine and warm it up.
Drive the vehicle.
Enter the following menus: Powertrain / Engine / DTC.
Read the DTCs.
- Result:
Display (DTC Output)
Proceed to
P1251
A
No output
B
|
|
||||
|
|
||||
| 4. INSPECT TURBO MOTOR DRIVER (POWER SOURCE CIRCUIT) |
Disconnect the turbo motor driver connector.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
for Bank 1 Tester Connection
Condition
Specified Condition
Turbo motor driver connector-3 (+B) - Turbo motor driver connector-4 (GND)
Ignition switch ON
11 to 14 V
for Bank 2 Tester Connection
Condition
Specified Condition
Turbo motor driver connector-3 (+B2) - Turbo motor driver connector-4 (GND2)
Ignition switch ON
11 to 14 V
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
for Bank 1 Tester Connection
Condition
Specified Condition
Turbo motor driver connector-4 (GND) - Body ground
Always
Below 1 Ω
for Bank 2 Tester Connection
Condition
Specified Condition
Turbo motor driver connector-4 (GND2) - Body ground
Always
Below 1 Ω
|
|
||||
| OK | |
| 5. CHECK HARNESS AND CONNECTOR (TURBO MOTOR DRIVER - ECM) |
Disconnect the turbo motor driver connector.
Disconnect the ECM connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance (Check for Open):
for LHD Tester Connection
Condition
Specified Condition
C45-49 (VNTO) - B-4 (VNTO)
Always
Below 1 Ω
C45-50 (VNTI) - B-3 (VNTI)
Always
Below 1 Ω
C45-47 (VNO2) - D-4 (VNO2)
Always
Below 1 Ω
C45-48 (VNI2) - D-3 (VNI2)
Always
Below 1 Ω
for RHD Tester Connection
Condition
Specified Condition
C46-49 (VNTO) - B-4 (VNTO)
Always
Below 1 Ω
C46-50 (VNTI) - B-3 (VNTI)
Always
Below 1 Ω
C46-47 (VNO2) - D-4 (VNO2)
Always
Below 1 Ω
C46-48 (VNI2) - D-3 (VNI2)
Always
Below 1 Ω
- Standard Resistance (Check for Short):
for LHD Tester Connection
Condition
Specified Condition
C45-49 (VNTO) or B-4 (VNTO) - Body ground
Always
10 kΩ or higher
C45-50 (VNTI) or B-3 (VNTI) - Body ground
Always
10 kΩ or higher
C45-47 (VNO2) or D-4 (VNO2) - Body ground
Always
10 kΩ or higher
C45-48 (VNI2) or D-3 (VNI2) - Body ground
Always
10 kΩ or higher
for RHD Tester Connection
Condition
Specified Condition
C46-49 (VNTO) or B-4 (VNTO) - Body ground
Always
10 kΩ or higher
C46-50 (VNTI) or B-3 (VNTI) - Body ground
Always
10 kΩ or higher
C46-47 (VNO2) or D-4 (VNO2) - Body ground
Always
10 kΩ or higher
C46-48 (VNI2) or D-3 (VNI2) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 6. CHECK HARNESS AND CONNECTOR (DC MOTOR - TURBO MOTOR DRIVER) |
Disconnect the DC motor connector.

Disconnect the turbo motor driver connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance (Check for Open):
for Bank 1 Tester Connection
Condition
Specified Condition
DC motor connector-1 (M-) - Turbo motor driver connector-2 (M-)
Always
Below 1 Ω
DC motor connector-2 (M+) - Turbo motor driver connector-1 (M+)
Always
Below 1 Ω
for Bank 2 Tester Connection
Condition
Specified Condition
DC motor connector-1 (M2-) - Turbo motor driver connector-2 (M2-)
Always
Below 1 Ω
DC motor connector-2 (M2+) - Turbo motor driver connector-1 (M2+)
Always
Below 1 Ω
- Standard Resistance (Check for Short):
for Bank 1 Tester Connection
Condition
Specified Condition
DC motor connector-1 (M-) or Turbo motor driver connector-2 (M-) - Body ground
Always
10 kΩ or higher
DC motor connector-2 (M+) or Turbo motor driver connector-1 (M+) - Body ground
Always
10 kΩ or higher
for Bank 2 Tester Connection
Condition
Specified Condition
DC motor connector-1 (M2-) or Turbo motor driver connector-2 (M2-) - Body ground
Always
10 kΩ or higher
DC motor connector-2 (M2+) or Turbo motor driver connector-1 (M2+) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 7. REPLACE TURBO MOTOR DRIVER (for Bank 1 and/or Bank 2) |
Replace the turbo motor driver (for Bank 1 and/or Bank 2) (Click here).
| NEXT | |
| 8. CHECK WHETHER DTC OUTPUT RECURS (DTC P1251) |
Connect the intelligent tester to the DLC3.
Turn the ignition switch to ON and turn the tester on.
Enter the following menus: Powertrain / Engine / DTC / Clear.
Clear the DTCs (Click here).
Turn the ignition switch off.
Start the engine and warm it up.
Drive the vehicle.
Enter the following menus: Powertrain / Engine / DTC.
Read the DTCs.
Result Display (DTC Output)
Proceed to
P1251
A
No output
B
|
|
||||
| A | |
| 9. REPLACE TURBOCHARGER SUB-ASSEMBLY (for Bank 1 and/or Bank 2) (DC MOTOR) |
Replace the turbocharger sub-assembly (for Bank 1 or Bank 2) (Click here).
|
|
||||
| 10. REPAIR OR REPLACE HARNESS OR CONNECTOR |
|
|
||||
| 11. REPLACE ECM |
Replace the ECM (Click here).
| NEXT | |
| 12. CONFIRM WHETHER MALFUNCTION HAS BEEN SUCCESSFULLY REPAIRED |
Connect the intelligent tester to the DLC3.
Clear the DTCs (Click here).
Turn the ignition switch off.
Start the engine and warm it up.
Run the engine with a heavy load at a mid to high engine speed.
Confirm that the DTC is not output again.
- HINT:
- Perform the following procedure using the tester to determine whether or not the DTC judgment has been carried out.
Enter the following menus: Powertrain / Engine / Utility / All Readiness.
Input DTC P1251.
Check that STATUS is NORMAL. If STATUS is INCOMPLETE or UNKNOWN, increase the time spent running the engine with a heavy load at a mid to high engine speed.
| NEXT | ||
| ||

