2011-2013 Land Cruiser · Service Manual Power Source / Network

B1206 P/W Master Switch Communication Stop

Diagnostic trouble codes · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

This DTC is stored when LIN communication between the master switch and main body ECU (cowl side junction block LH) stops for 10 seconds or more.
DTC Code
DTC Detection Condition
Trouble Area
B1206
No communication between master switch and main body ECU (cowl side junction block LH) for 10 seconds or more.
  1. Master switch
  2. Main body ECU (cowl side junction block LH)
  3. Harness or connector

WIRING DIAGRAM

B173719E21

INSPECTION PROCEDURE

NOTICE:
When using the intelligent tester with the ignition switch off to troubleshoot:
Connect the intelligent tester to the vehicle, and turn a courtesy switch on and off at 1.5 second intervals until communication between the intelligent tester and vehicle begins.

HINT:
DTC B2325 is stored when the communication between the master switch and main body ECU (cowl side junction block LH) stops.


1. CLEAR DTC
  1. Clear the DTC (Click here).


NEXT


2. CHECK FOR DTC
  1. Recheck for DTCs (Click here).

    Result 
    Result
    Proceed to
    DTC B1206 is output
    A
    DTC B1206 is not output
    B



B
USE SIMULATION METHOD TO CHECK (Click here)
A


3. CHECK HARNESS AND CONNECTOR (MAIN BODY ECU - MASTER SWITCH)
E156400E02
  1. Disconnect the E3 ECU connector.

  1. Disconnect the I11*1 or I22*2 switch connector.

    HINT:
    1. *1: for LHD
    2. *2: for RHD

  1. Measure the resistance and voltage according to the value(s) in the tables below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    E3-10 (LIN2) - I11-17 (LIN1)*1 or I22-17 (LIN)*2
    Always
    Below 1 Ω
    E3-10 (LIN2) - Body ground
    Always
    10 kΩ or higher

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    E3-10 (LIN2) - Body ground
    Always
    Below 1 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. CHECK MASTER SWITCH ASSEMBLY (BATTERY VOLTAGE AND BODY GROUND)

  1. B163102E04
    Disconnect the I11*1 or I22*2 switch connector.

    HINT:
    1. *1: for LHD
    2. *2: for RHD

  1. Measure the resistance and voltage according to the value(s) in the tables below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    I11-12 (GND)*1 or I22-12 (GND)*2 - Body ground
    Always
    Below 1 Ω

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    I11-11 (B)*1 or I22-11 (B)*2 - Body ground
    Always
    11 to 14 V



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


5. REPLACE MASTER SWITCH ASSEMBLY
  1. Temporarily replace the master switch assembly with a new or normally functioning one (Click here).

  1. Clear the DTC (Click here).


NEXT


6. CHECK FOR DTC
  1. Recheck for DTCs (Click here).

    Result 
    Result
    Proceed to
    DTC B1206 is not output
    A
    DTC B1206 is output
    B



B
REPLACE MAIN BODY ECU (COWL SIDE JUNCTION BLOCK LH)
A

END (MASTER SWITCH IS DEFECTIVE)


← B1206 P/W Master Switch Communication Stop (Sep 2011 – Dec 2011)B1249 Double Locking ECU Communication Stop (from Sep 2011) →