Illumination Circuit
Circuit diagnosis · Vehicles built from Jan 2012
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
DESCRIPTION
When a door is opened while the DOOR switch of the map light assembly is on, the map light assembly receives a door open signal from the main body ECU and turns on the corresponding lights.WIRING DIAGRAM




INSPECTION PROCEDURE
| 1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER |
Operate the intelligent tester according to the steps on the display and select "Active Test".
Main Body Tester Display
Test Part
Control Range
Diagnostic Note
Illuminated Entry System
Illumination light
OFF or ON
-
- OK:
- Light comes on.
|
|
||||
| OK | ||
| ||
| 2. INSPECT FUSE (DOME2) |
Remove the DOME2 fuse from the engine room junction block.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
DOME2 fuse
Always
Below 1 Ω
|
|
||||
| OK | |
| 3. CHECK VEHICLE TYPE |
Check the vehicle type.
Result Result
Proceed to
w/o Map Light
A
w/ Map Light
B
|
|
||||
| A | |
| 4. CHECK HARNESS AND CONNECTOR (DOME LIGHT - MAP LIGHT AND BODY GROUND) |
Disconnect the 2D ECU connector.
Disconnect the R13 light connector.


Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
2D-51 (ILE) - R13-2 (CTY)
Always
Below 1 Ω
R13-1 (B) - Body ground
R13-3 (E) - Body ground
2D-51 (ILE) - Body ground
Always
10 kΩ or higher
Disconnect the R15 light connector.


Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
2D-51 (ILE) - R15-2 (DL)
Always
Below 1 Ω
R15-1 (DB) - Body ground
R15-3 (L) - Body ground
2D-51 (ILE) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | ||
| ||
| 5. CHECK HARNESS AND CONNECTOR (MAP LIGHT - BODY GROUND) |
Disconnect the 2D ECU connector.

Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Condition
Specified Condition
R7-16 (+B3) - Body ground
Always
11 to 14 V
|
|
||||
| OK | |
| 6. INSPECT MAP LIGHT |
![]() ![]() |
Remove the map light (Click here).
Measure the voltage according to the value(s) in the table below.
- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
R7-31 (+B1) - R7-5 (RRVT)
Dome light switch off
Below 1 V
Dome light switch on
11 to 14 V
R7-6 (RILL) - R7-32 (ILLB)
Dome light switch off
Below 1 V
Dome light switch on
11 to 14 V
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Switch Condition
Specified Condition
R7-9 (CTY) - Body ground
"Door" switch on and door open
Below 1 Ω
"Door" switch off and door open
10 kΩ or higher
"Door" switch on and door closed
10 kΩ or higher
"Door" switch off and door closed
10 kΩ or higher
R7-17 (GND9) - Body ground
Always
Below 1 Ω
|
|
||||
| OK | |
| 7. CHECK HARNESS AND CONNECTOR (NO. 3 ROOM LIGHT - MAP LIGHT AND BODY GROUND) |
Disconnect the R7 map light connector.
Disconnect the R6 light connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
R7-31 (+B1) - R6-1 (DB)
Always
Below 1 Ω
R7-5 (RRVT) - R6-3 (DL)
R6-2 (L) - Body ground
R7-31 (+B1) - Body ground
Always
10 kΩ or higher
R7-16 (RRVT) - Body ground
|
|
||||
| OK | |
| 8. CHECK VEHICLE TYPE |
Check the vehicle type.
Result Result
Proceed to
w/ Sliding Roof
A
w/o Sliding Roof
B
|
|
||||
| A | |
| 9. CHECK HARNESS AND CONNECTOR (SPOT LIGHT - MAP LIGHT AND BODY GROUND) |
Disconnect the R7 map light connector.
Disconnect the R4 light connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
R7-32 (ILLB) - R4-1 (B)
Always
Below 1 Ω
R7-6 (RILL) - R4-2 (CTY)
R7-32 (ILLB) - Body ground
Always
10 kΩ or higher
R7-6 (RILL) - Body ground
for LH:

Disconnect the R8 light connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
R7-32 (ILLB) - R8-2 (BL)
Always
Below 1 Ω
R7-1 (RGND) - R8-4 (E)
R7-32 (ILLB) - Body ground
Always
10 kΩ or higher
R7-1 (RGND) - Body ground
for RH:
Disconnect the R9 light connector.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
R7-32 (ILLB) - R9-2 (BR)
Always
Below 1 Ω
R7-1 (RGND) - R9-4 (ER)
R7-32 (ILLB) - Body ground
Always
10 kΩ or higher
R7-1 (RGND) - Body ground
|
|
||||
| OK | ||
| ||
| 10. CHECK HARNESS AND CONNECTOR (NO. 1 ROOM LIGHT - MAP LIGHT AND BODY GROUND) |
Disconnect the R7 map light connector.
Disconnect the R12 light connector.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
R7-32 (ILLB) - R12-1 (B)
Always
Below 1 Ω
R7-6 (RILL) - R12-3 (CTY)
R12-2 (E) - R7-1 (RGND)
R7-32 (ILLB) - Body ground
Always
10 kΩ or higher
R7-6 (RILL) - Body ground
|
|
||||
| OK | ||
| ||

