2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

Fuel Pump Control Circuit

Circuit diagnosis · Vehicles built Sep 2011 – Dec 2011

DESCRIPTION

The fuel pump circuit consists of the ECM, fuel pump and fuel pump ECU (which operates the fuel pump). Based on the engine output, the ECM determines the fuel pump speed. The speed is then converted to a duty signal and sent to the fuel pump ECU. Based on the signal sent from the ECM, the fuel pump ECU adjusts the fuel pump operation speed between 3 settings.

WIRING DIAGRAM

A182115E01

INSPECTION PROCEDURE

This troubleshooting procedure is based on the premise that the engine is started. If the engine is not started, proceed to the Problem Symptoms Table (Click here).

1. PERFORM ACTIVE TEST USING INTELLIGENT TESTER (FUEL PUMP)
  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG) and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

  1. Check whether operating sounds can be heard while operating the relay using the tester.

    OK:
    Operating sounds can be heard from relay.



NG
Go to step 5
OK


2. CHECK HARNESS AND CONNECTOR (FUEL PUMP ECU - ECM - FUEL PUMP)
A181565E01
  1. Disconnect the fuel pump ECU connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (for LHD):
    Tester Connection
    Condition
    Specified Condition
    N2-5 (FPC) - A38-52 (FPC)
    Always
    Below 1 Ω
    N2-4 (DI) - A38-18 (DI)
    Always
    Below 1 Ω
    N2-6 (E) - Body ground
    Always
    Below 1 Ω
    N2-5 (FPC) or A38-52 (FPC) - Body ground
    Always
    10 kΩ or more
    N2-4 (DI) or A38-18 (DI) - Body ground
    Always
    10 kΩ or more
    N2-1 (FP-) or N1-5 (E2) - Body ground
    Always
    10 kΩ or more

    Standard Resistance (for RHD):
    Tester Connection
    Condition
    Specified Condition
    N2-5 (FPC) - A52-52 (FPC)
    Always
    Below 1 Ω
    N2-4 (DI) - A52-18 (DI)
    Always
    Below 1 Ω
    N2-6 (E) - Body ground
    Always
    Below 1 Ω
    N2-5 (FPC) or A52-52 (FPC) - Body ground
    Always
    10 kΩ or more
    N2-4 (DI) or A52-18 (DI) - Body ground
    Always
    10 kΩ or more
    N2-1 (FP-) or N1-5 (E2) - Body ground
    Always
    10 kΩ or more



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


3. REPLACE FUEL PUMP CONTROL ECU
  1. Replace the fuel pump control ECU (Click here).


NEXT


4. CHECK PROBLEM SYMPTOM DISAPPEARS
  1. Check if the problem symptom disappears.

    Result 
    Result
    Proceed to
    Problem symptom disappears
    A
    Problem symptom does not disappear
    B



B
Go to step 15
A

END

5. CHECK FUEL PUMP (POWER SOURCE VOLTAGE)

  1. E114283E16
    Disconnect the fuel pump connector.

  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG) and turn the tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Condition
    Specified Condition
    N1-4 - N1-5
    Engine switch on (IG)
    Active Test on
    11 to 14 V

    Result 
    Result
    Proceed to
    OK
    A
    NG (for Single Tank Type)
    B
    NG (for Double Tank Type)
    C



B
REPLACE FUEL PUMP (Click here)

C
REPLACE FUEL PUMP (Click here)
A


6. CHECK HARNESS AND CONNECTOR (ECM - FUEL PUMP CONTROL ECU - FUEL PUMP)
A181565E02
  1. Disconnect the ECM connector.

  1. Disconnect the fuel pump ECU connector.

  1. Disconnect the fuel pump connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (for LHD):
    Tester Connection
    Condition
    Specified Condition
    N2-5 (FPC) - A38-52 (FPC)
    Always
    Below 1 Ω
    N2-4 (DI) - A38-18 (DI)
    Always
    Below 1 Ω
    N2-6 (E) - Body ground
    Always
    Below 1 Ω
    N2-2 (FP+) - N1-4 (B2)
    Always
    Below 1 Ω
    N2-1 (FP-) - N1-5 (E2)
    Always
    Below 1 Ω
    N2-5 (FPC) or A38-52 (FPC) - Body ground
    Always
    10 kΩ or more
    N2-4 (DI) or A38-18 (DI) - Body ground
    Always
    10 kΩ or more
    N2-2 (FP+) or N1-4 (B2) - Body ground
    Always
    10 kΩ or more
    N2-1 (FP-) or N1-5 (E2) - Body ground
    Always
    10 kΩ or more

    Standard Resistance (for RHD):
    Tester Connection
    Condition
    Specified Condition
    N2-5 (FPC) - A52-52 (FPC)
    Always
    Below 1 Ω
    N2-4 (DI) - A52-18 (DI)
    Always
    Below 1 Ω
    N2-6 (E) - Body ground
    Always
    Below 1 Ω
    N2-2 (FP+) - N1-4 (B2)
    Always
    Below 1 Ω
    N2-1 (FP-) - N1-5 (E2)
    Always
    Below 1 Ω
    N2-5 (FPC) or A52-52 (FPC) - Body ground
    Always
    10 kΩ or more
    N2-4 (DI) or A52-18 (DI) - Body ground
    Always
    10 kΩ or more
    N2-2 (FP+) or N1-4 (B2) - Body ground
    Always
    10 kΩ or more
    N2-1 (FP-) or N1-5 (E2) - Body ground
    Always
    10 kΩ or more



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


7. CHECK FUEL PUMP CONTROL ECU (POWER SOURCE VOLTAGE)

  1. A181918E01
    Disconnect the fuel pump ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    N2-3 (+B) - Body ground
    Engine switch on (IG)
    11 to 14 V



NG
Go to step 10
OK


8. REPLACE FUEL PUMP CONTROL ECU
  1. Replace the fuel pump control ECU (Click here).


NEXT


9. CHECK PROBLEM SYMPTOM DISAPPEARS
  1. Check if the problem symptom disappears.

    Result 
    Result
    Proceed to
    Problem symptom disappears
    A
    Problem symptom does not disappear
    B



B
Go to step 15
A

END

10. INSPECT CIRCUIT OPENING RELAY (C/OPN)
B016200E02
  1. Remove the circuit opening relay (C/OPN) from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    3 - 5
    Battery voltage not applied to terminals 1 and 2
    10 kΩ or higher
    3 - 5
    Battery voltage applied to terminals 1 and 2
    Below 1 Ω



NG
REPLACE CIRCUIT OPENING RELAY (C/OPN)
OK


11. CHECK CIRCUIT OPENING RELAY
  1. Check the operating sound of the relay when the engine switch is turned on (IG).

    OK:
    Tester Connection
    Switch Condition
    Specified Condition
    C/OPN relay
    Engine switch on (IG)
    Operating sound heard



NG
Go to step 13
OK


12. CHECK HARNESS AND CONNECTOR (FUEL PUMP ECU - CIRCUIT OPENING RELAY - INTEGRATION RELAY)

  1. A181919E01
    Remove the circuit opening relay (C/OPN) and integration relay from the engine room relay block.

  1. Disconnect the fuel pump ECU connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    N2-3 (+B) - C/OPN relay terminal 3
    Always
    Below 1 Ω
    1B-4 - C/OPN relay terminal 5
    Always
    Below 1 Ω
    N2 or 3 (+B) - C/OPN relay terminal 3 - Body ground
    Always
    10 kΩ or more
    1B or 4 - C/OPN relay terminal 5 - Body ground
    Always
    10 kΩ or more



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

GO TO ECU POWER SOURCE CIRCUIT (Click here)

13. INSPECT FUSE (IGN)

  1. A181568E01
    Remove the IGN fuse from the integration relay.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    IGN fuse
    Always
    Below 1 Ω

  1. Reinstall the IGN fuse.



NG
CHECK FOR SHORTS IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE
OK


14. CHECK HARNESS AND CONNECTOR (ECM - CIRCUIT OPENING RELAY - INTEGRATION)

  1. A185395E01
    Remove the circuit opening relay (C/OPN) and integration relay from the engine room relay block.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (for LHD):
    Tester Connection
    Condition
    Specified Condition
    A38-48(FC) - 1
    Always
    Below 1 Ω
    1B-8 - 2
    Always
    Below 1 Ω
    A38-48(FC) - 1 or Body ground
    Always
    10 kΩ or more
    1B-8 or 2 - Body ground
    Always
    10 kΩ or more

    Standard Resistance (for RHD):
    Tester Connection
    Condition
    Specified Condition
    A52-48(FC) - 1
    Always
    Below 1 Ω
    1B-8 - 2
    Always
    Below 1 Ω
    A52-48(FC) - 1 or Body ground
    Always
    10 kΩ or more
    1B-8 or 2 - Body ground
    Always
    10 kΩ or more



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


15. REPLACE ECM
  1. Replace the ECM (Click here).


NEXT


16. CHECK PROBLEM SYMPTOM DISAPPEARS
  1. Check if the problem symptom disappears.

    Result 
    Result
    Proceed to
    Problem symptom disappears
    A
    Problem symptom does not disappear
    B



B
GO TO PROBLEM SYMPTOMS TABLE (Click here)
A

END


← VC Output Circuit (Sep 2011 – Dec 2011)Fuel Injector Circuit (Sep 2011 – Dec 2011) →