2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

Fuel Injector Circuit

Circuit diagnosis · Vehicles built Sep 2011 – Dec 2011

DESCRIPTION

The fuel injectors are located on the intake manifold. They inject fuel into the cylinders based on the signals from the ECM.

WIRING DIAGRAM

A182116E01

INSPECTION PROCEDURE


1. CHECK INJECTOR ASSEMBLY (POWER SOURCE)
A182504E01
  1. Disconnect the fuel injector connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard voltage:
    Cylinder
    Tester Connection
    Switch Condition
    Specified Condition
    No. 1
    C5-1 - Ground
    Engine switch on (IG)
    11 to 14 V
    No. 2
    C16-1 - Ground
    Engine switch on (IG)
    11 to 14 V
    No. 3
    C7-1 - Ground
    Engine switch on (IG)
    11 to 14 V
    No. 4
    C14-1 - Ground
    Engine switch on (IG)
    11 to 14 V
    No. 5
    C9-1 - Ground
    Engine switch on (IG)
    11 to 14 V
    No. 6
    C12-1 - Ground
    Engine switch on (IG)
    11 to 14 V
    No. 7
    C52-1 - Ground
    Engine switch on (IG)
    11 to 14 V
    No. 8
    C54-1 - Ground
    Engine switch on (IG)
    11 to 14 V



NG
Go to step 6
OK


2. INSPECT FUEL INJECTOR ASSEMBLY
  1. Inspect the fuel injector (Click here).



NG
REPLACE FUEL INJECTOR ASSEMBLY (Click here)
OK


3. CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - ECM)
A181795E02
  1. Disconnect the fuel injector connector.

  1. Disconnect the ECM connector.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance (for LHD):
    Cylinder
    Tester Connection
    Condition
    Specified Condition
    No. 1
    C5-2 - Body ground
    Always
    10 kΩ or higher
    C5-2 - C45-86 (#10)
    Always
    Below 1 Ω
    No. 2
    C16-2 - Body ground
    Always
    10 kΩ or higher
    C16-2 - C45-109 (#20)
    Always
    Below 1 Ω
    No. 3
    C7-2 - Body ground
    Always
    10 kΩ or higher
    C7-2 - C45-85 (#30)
    Always
    Below 1 Ω
    No. 4
    C14-2 - Body ground
    Always
    10 kΩ or higher
    C14-2 - C45-108 (#40)
    Always
    Below 1 Ω
    No. 5
    C9-2 - Body ground
    Always
    10 kΩ or higher
    C9-2 - C45-84 (#50)
    Always
    Below 1 Ω
    No. 6
    C12-2 - Body ground
    Always
    10 kΩ or higher
    C12-2 - C45-107 (#60)
    Always
    Below 1 Ω
    No. 7
    C52-2 - Body ground
    Always
    10 kΩ or higher
    C52-2 - C45-83 (#70)
    Always
    Below 1 Ω
    No. 8
    C54-2 - Body ground
    Always
    10 kΩ or higher
    C54-2 - C45-106 (#80)
    Always
    Below 1 Ω

    Standard Resistance (for RHD):
    Cylinder
    Tester Connection
    Condition
    Specified Condition
    No. 1
    C5-2 - Body ground
    Always
    10 kΩ or higher
    C5-2 - C46-86 (#10)
    Always
    Below 1 Ω
    No. 2
    C16-2 - Body ground
    Always
    10 kΩ or higher
    C16-2 - C46-109 (#20)
    Always
    Below 1 Ω
    No. 3
    C7-2 - Body ground
    Always
    10 kΩ or higher
    C7-2 - C46-85 (#30)
    Always
    Below 1 Ω
    No. 4
    C14-2 - Body ground
    Always
    10 kΩ or higher
    C14-2 - C46-108 (#40)
    Always
    Below 1 Ω
    No. 5
    C9-2 - Body ground
    Always
    10 kΩ or higher
    C9-2 - C46-84 (#50)
    Always
    Below 1 Ω
    No. 6
    C12-2 - Body ground
    Always
    10 kΩ or higher
    C12-2 - C46-107 (#60)
    Always
    Below 1 Ω
    No. 7
    C52-2 - Body ground
    Always
    10 kΩ or higher
    C52-2 - C46-83 (#70)
    Always
    Below 1 Ω
    No. 8
    C54-2 - Body ground
    Always
    10 kΩ or higher
    C54-2 - C46-106 (#80)
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK


4. REPLACE ECM
  1. Replace the ECM (Click here).


NEXT


5. CHECK PROBLEM SYMPTOM DISAPPEARS
  1. Check if the problem symptom disappears.

    Result 
    Result
    Proceed to
    Problem symptom disappears
    A
    Problem symptom does not disappear
    B



B
GO TO PROBLEM SYMPTOMS TABLE (Click here)
A

END

6. INSPECT FUSE (INJ)
A181865E01
  1. Remove the INJ fuse from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    INJ fuse
    Always
    Below 1 Ω



NG
CHECK FOR SHORT IN ALL HARNESSES AND CONNECTORS CONNECTED TO FUSE AND REPLACE FUSE
OK


7. CHECK HARNESS AND CONNECTOR (FUEL INJECTOR ASSEMBLY - INTEGRATION RELAY)
A181796E01
  1. Disconnect the fuel injector connector.

  1. Remove the integration relay from the engine room relay block.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Cylinder
    Tester Connection
    Condition
    Specified Condition
    No. 1
    C5-2 - Body ground
    Always
    10 kΩ or higher
    C5-2 - 1B-8
    Always
    Below 1 Ω
    No. 2
    C16-2 - Body ground
    Always
    10 kΩ or higher
    C16-2 - 1B-8
    Always
    Below 1 Ω
    No. 3
    C7-2 - Body ground
    Always
    10 kΩ or higher
    C7-2 - 1B-8
    Always
    Below 1 Ω
    No. 4
    C14-2 - Body ground
    Always
    10 kΩ or higher
    C14-2 - 1B-8
    Always
    Below 1 Ω
    No. 5
    C9-2 - Body ground
    Always
    10 kΩ or higher
    C9-2 - 1B-8
    Always
    Below 1 Ω
    No. 6
    C12-2 - Body ground
    Always
    10 kΩ or higher
    C12-2 - 1B-8
    Always
    Below 1 Ω
    No. 7
    C52-2 - Body ground
    Always
    10 kΩ or higher
    C52-2 - 1B-8
    Always
    Below 1 Ω
    No. 8
    C54-2 - Body ground
    Always
    10 kΩ or higher
    C54-2 - 1B-8
    Always
    Below 1 Ω



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

CHECK ECU POWER SOURCE CIRCUIT (Click here)


← Fuel Pump Control Circuit (Sep 2011 – Dec 2011)Cranking Holding Function Circuit (Sep 2011 – Dec 2011) →