2011-2013 Land Cruiser · Service Manual Drivetrain

REMOVAL

Removal / installation · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


1. PRECAUTION

NOTICE:
After turning the ignition switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here)


2. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


3. REMOVE UPPER CONSOLE PANEL SUB-ASSEMBLY
w/o Console Box Lid (Click here)
w/ Cool Box (Click here)
w/o Cool Box (Click here)

4. REMOVE SHIFT LEVER BOOT ASSEMBLY

C172726
  1. Remove the 4 screws, shift lever retainer and shift lever boot.


5. REMOVE FLOOR SHIFT LEVER ASSEMBLY

C176506E01
  1. Cover the shift lever cap with a cloth.

  1. Press down on the shift lever cap and rotate it counterclockwise to remove it.

  1. Pull out the shift lever.


6. REMOVE NO. 1 ENGINE COVER SUB-ASSEMBLY (w/ Intercooler)

  1. A174701
    Remove the 2 nuts and No. 1 engine cover.


7. REMOVE INTERCOOLER ASSEMBLY (w/ Intercooler)

  1. A174703
    Loosen the No. 1 air hose clamp.

  1. A174702
    Loosen the No. 2 air hose clamp.

  1. A174704
    Disconnect the turbo pressure sensor connector, intake air temperature sensor connector and vacuum hose.

  1. A174705
    Remove the 6 nuts, 2 bolts and intercooler.

  1. Remove the 2 gaskets from the air tube LH and RH.


8. REMOVE NO. 2 COOL AIR INLET (w/o Intercooler)

  1. A257027
    Loosen the No. 2 air hose clamp.

  1. A257029
    Remove the 3 nuts, bolt and No. 2 cool air inlet.

  1. Remove the gasket from the air tube LH.


9. DRAIN CLUTCH FLUID

10. REMOVE CLUTCH HOSE (for 1VD-FTV)

  1. A177028
    Disconnect the 2 flexible hose tubes from the clutch hose with a 10 mm union nut wrench while holding the flexible hose with a wrench.

    NOTICE:
    1. Do not bend or damage the flexible hose tubes.
    2. Do not allow any foreign matter such as dirt and dust to enter the flexible hose tubes from the connecting point.

  1. Remove the 2 clips.

  1. A183845
    Remove the bolt and clutch hose.


11. REMOVE AIR TUBE SUB-ASSEMBLY LH (for 1VD-FTV)

A174728
  1. Loosen the hose clamp.

  1. Remove the air tube from the throttle body.


12. REMOVE TUBE CONNECTOR TO FLEXIBLE HOSE TUBE (for 1VD-FTV)

  1. A177030
    Using a 10 mm union nut wrench, disconnect the tube connector to flexible hose tube from the clutch tube to release cylinder 2 way.

    NOTICE:
    1. Do not bend or damage the flexible hose tube.
    2. Do not allow any foreign matter such as dirt and dust to enter the flexible hose tube from the connecting point.

  1. A177031
    Remove the 2 bolts and tube connector to flexible hose tube.


13. REMOVE TRANSFER HEAT INSULATOR

  1. C171487
    Remove the 4 bolts and insulator.


14. REMOVE TRANSFER DYNAMIC DAMPER (for 1VD-FTV)

C173746
  1. Remove the 2 bolts and transfer dynamic damper.


15. REMOVE LOWER TRANSFER CASE PROTECTOR

C173748
  1. Remove the 7 bolts and lower transfer case protector.


16. DRAIN MANUAL TRANSMISSION OIL

C172955
  1. Remove the drain plug and gasket and then drain the manual transmission oil.

  1. C174902
    Remove the filler plug and gasket.

  1. Install a new gasket and the drain plug.

    Torque:
    37 N*m{ 380 kgf*cm , 27 ft.*lbf }


17. DRAIN TRANSFER OIL

  1. C173746
    except 1GR-FE:
    Remove the 2 bolts and transfer dynamic damper.

  1. C171487
    Remove the 4 bolts and transfer heat insulator.

  1. C173748
    Remove the 7 bolts and lower transfer case protector.

  1. C172047
    Remove the filler plug and gasket.

  1. C172046
    Remove the drain plug and gasket, and drain the transfer oil.


18. REMOVE PROPELLER SHAFT ASSEMBLY
(Click here)

19. REMOVE FRONT PROPELLER SHAFT ASSEMBLY
(Click here)

20. REMOVE EXHAUST PIPE (for 1GR-FE)
(Click here)

21. REMOVE EXHAUST PIPE (for 1VD-FTV)
(Click here)

22. REMOVE MANIFOLD STAY (for 1GR-FE)

  1. A176352
    Remove the 3 bolts and No. 1 manifold stay.


23. REMOVE NO. 2 MANIFOLD STAY (for 1GR-FE)

  1. A176353
    Remove the 3 bolts and No. 2 manifold stay.


24. REMOVE STARTER ASSEMBLY (for 1GR-FE)
  1. for 1.4 kW Type:
    Remove the starter assembly (Click here).

  1. for 2.0 kW Type:
    Remove the starter assembly (Click here).


25. REMOVE NO. 2 FRAME CROSSMEMBER SUB-ASSEMBLY
  1. Support the transmission with a transmission jack. Lift the transmission slightly from the crossmember.

  1. C176551
    Remove the 4 bolts of the rear engine mounting insulator.

  1. C176552
    Remove the 4 bolts, 4 nuts, 4 washers and frame crossmember.


26. REMOVE REAR NO. 1 ENGINE MOUNTING INSULATOR

  1. C176553
    Remove the 4 bolts and engine mounting insulator.


27. REMOVE TRANSFER BREATHER HOSE SUB-ASSEMBLY (for 1GR-FE)

  1. C172728
    Disconnect the breather hose from the transfer and actuator, and disconnect the 2 clamps.

  1. C172948
    Disconnect the 5 clamps.

  1. C172729
    Disconnect the 2 breather hoses from the bracket.


28. REMOVE TRANSFER BREATHER HOSE SUB-ASSEMBLY (for 1VD-FTV)

  1. C172728
    Disconnect the breather hose from the transfer and actuator, and disconnect the 2 clamps.

  1. C172949
    Disconnect the 3 clamps.

  1. C172727
    Disconnect the 3 breather hoses from the bracket.

  1. Remove the bolt and disconnect the bracket from the transmission.


29. DISCONNECT WIRE HARNESS (for 1GR-FE)

  1. C172711
    Disconnect the 2 connectors and 3 clamps.

  1. C172714
    Remove the bolt and disconnect the ground cable.

  1. Tilt the transmission downward.

    NOTICE:
    Make sure the cooling fan does not contact the fan shroud.

  1. C172951E01
    Remove the 2 bolts.

  1. Disconnect the back-up light switch connector.

  1. Disconnect the 6 clamps.


30. DISCONNECT WIRE HARNESS (for 1VD-FTV)

  1. C172711
    Disconnect the 2 connectors and 3 clamps.

  1. C172714
    Remove the bolt and disconnect the ground cable.

  1. Tilt the transmission downward.

    NOTICE:
    Make sure the cooling fan does not contact the fan shroud.

  1. C172950
    Disconnect the shift position switch connector.

  1. Disconnect the back-up light switch connector.

  1. Disconnect the 5 clamps.


31. REMOVE NO. 1 CLUTCH HOUSING COVER

C172725
  1. Remove the 3 bolts and clutch housing cover.


32. REMOVE CLUTCH RELEASE CYLINDER TO ACCUMULATOR TUBE

C271130
  1. Using a union nut wrench, disconnect the tube.

    HINT:
    Use a container to catch the fluid.

  1. Remove the 2 bolts and tube.


33. REMOVE CLUTCH ACCUMULATOR ASSEMBLY

C271134
  1. Using a union nut wrench, disconnect the flexible hose tube.

    HINT:
    Use a container to catch the fluid.

  1. C271135
    Remove the 3 bolts and clutch accumulator.


34. REMOVE CLUTCH RELEASE CYLINDER ASSEMBLY

C179745
  1. Remove the 2 bolts and pull out the clutch release cylinder.


35. REMOVE CLUTCH RELEASE CYLINDER TO FLEXIBLE HOSE TUBE

C179744E01
  1. Remove the 3 bolts and flexible hose tube.


36. REMOVE OIL PAN COVER (for 1VD-FTV)

C172956
  1. Remove the 2 bolts and oil pan cover.


37. REMOVE MANUAL TRANSMISSION WITH TRANSFER (for 1GR-FE)

C176669
  1. Remove the 9 bolts and manual transmission with transfer.


38. REMOVE MANUAL TRANSMISSION WITH TRANSFER (for 1VD-FTV)

C176668
  1. Remove the 10 bolts and manual transmission with transfer.


39. REMOVE TRANSFER ASSEMBLY

  1. C174591E01
    Remove the 8 transfer adaptor rear mounting bolts.

  1. Pull the transfer straight up and remove it from the transmission.

    NOTICE:
    Take care not to damage the adaptor oil seal with the transfer input shaft spline.


40. REMOVE CLUTCH RELEASE FORK SUB-ASSEMBLY

C173304
  1. Remove the clutch release fork with the clutch release bearing from the transmission unit.

  1. Remove the release fork support from the transmission unit.

  1. C163036
    Remove the clip and release bearing from the clutch release fork.

← COMPONENTS (from Jan 2012)REMOVAL (from Jan 2012) →