C1622 Open or Short Circuit in Back Camera Signal
Diagnostic trouble codes · Vehicles built Sep 2011 – Dec 2011
DESCRIPTION
This DTC is stored if the parking assist ECU judges as a result of its self check that the signals or signal lines between the parking assist ECU and the rear television camera assembly are not normal.| DTC No. |
DTC Detection Condition |
Trouble Area |
| C1622 |
An open or short in the rear television camera signal circuit |
|
WIRING DIAGRAM


INSPECTION PROCEDURE
- NOTICE:
- When "System initializing" is displayed on the display and navigation module display after the battery terminal disconnected, correct the steering angle neutral point (Click here).
- Depending on the parts that are replaced or operations that are performed during vehicle inspection or maintenance, calibration of other systems as well as the parking assist monitor system may be needed (Click here).
- When "System initializing" is displayed on the display and navigation module display after the battery terminal disconnected, correct the steering angle neutral point (Click here).
| 1. CHECK HARNESS AND CONNECTOR (PARKING ASSIST ECU - REAR TELEVISION CAMERA) |
Disconnect the F44 connector from the parking assist ECU.
Disconnect the S5 connector from the rear television camera assembly.
Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
F44-34 (CV-) - S5-1 (CV-)
Always
Below 1 Ω
F44-10 (CV+) - S5-2 (CV+)
Always
Below 1 Ω
F44-35 (CB+) - S5-4 (CB+)
Always
Below 1 Ω
F44-34 (CV-) - Body ground
Always
10 kΩ or higher
F44-10 (CV+) - Body ground
Always
10 kΩ or higher
F44-11 (CGND) - Body ground
Always
10 kΩ or higher
F44-35 (CB+) - Body ground
Always
10 kΩ or higher
|
|
||||
| OK | |
| 2. INSPECT PARKING ASSIST ECU (CV-, CGND) |
Reconnect the F44 connector to the parking assist ECU.

Measure the resistance according to the value(s) in the table below.
- Standard Resistance:
Tester Connection
Condition
Specified Condition
F44-34 (CV-) - Body ground
Always
Below 1 Ω
F44-11 (CGND) - Body ground
Always
Below 1 Ω
Text in Illustration *1
Component with harness connected
(Parking Assist ECU)
|
|
||||
| OK | |
| 3. INSPECT REAR TELEVISION CAMERA ASSEMBLY (CB+, CGND) |
Disconnect the S5 connector from the rear television camera assembly.
Measure the voltage according to the value(s) in the table below.

- Standard Voltage:
Tester Connection
Switch Condition
Specified Condition
S5-3 (CGND) - S5-4 (CB+)
Engine switch on (IG)
Shift lever in R
5.8 to 7.0 V
Text in Illustration *1
Front view of wire harness connector
(to Rear Television Camera Assembly)
|
|
||||
| OK | |
| 4. INSPECT PARKING ASSIST ECU (CV+, GND1) |
Reconnect the S5 connector to the rear television camera assembly.
Reconnect the F43 and F44 connectors to the parking assist ECU.


Check the waveform of the rear television camera assembly using an oscilloscope.

- HINT:
- A waterproof connector is used for the rear television camera assembly. Therefore, inspect the waveform at the parking assist ECU with the connector connected.
- OK:
- Waveform is as shown in the illustration.
Item
Content
Terminal No. (Symbol)
F44-10 (CV+) - F43-4 (GND1)
Tool Setting
200 mV/DIV., 50 μsec./DIV.
Condition
Engine switch on (IG), shift lever in R
- HINT:
- The video waveform changes according to the image sent by the rear television camera assembly.
Text in Illustration *1
Component with harness connected
(Parking Assist ECU)
*2
Waveform 1 (under normal conditions)
*3
Waveform 2 (camera lens is covered, blacking out the screen)
*4
Synchronized Signal
*5
Video Waveform
|
|
||||
| OK | ||
| ||
