2011-2013 Land Cruiser · Service Manual Audio / Visual / Telematics

Clearance Sonar Main Switch Circuit

Circuit diagnosis · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

When the back sonar or clearance sonar switch assembly turns on, the ON signal is input into the parking assist ECU*1 or clearance warning ECU assembly*2.
  1. *1: w/ Side Monitor System
  2. *2: w/o Side Monitor System

WIRING DIAGRAM

E246938E01
E246938E02

INSPECTION PROCEDURE


1. READ VALUE USING INTELLIGENT TESTER (BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY)
  1. Check the Data List for proper functioning of the back sonar or clearance sonar main switch assembly (Click here).

    Clearance Sonar 
    Tester Display
    Measurement Item/Range
    Normal Condition
    Diagnostic Note
    Main Switch
    Back sonar or clearance sonar switch assembly / ON or OFF
    OFF: Back sonar or clearance sonar switch assembly off
    ON: Back sonar or clearance sonar switch assembly on
    -

    OK:
    The intelligent tester display changes according to operation of back sonar or clearance sonar switch assembly.



NG
Go to step 2
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

2. INSPECT BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY
  1. Remove the back sonar or clearance sonar switch assembly (Click here).

  1. Inspect the back sonar or clearance sonar switch assembly (Click here).

    Result 
    Result
    Proceed to
    OK (w/ Side Monitor System)
    A
    OK (w/o Side Monitor System)
    B
    NG
    C



B
Go to step 4

C
REPLACE BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY (Click here)
A


3. CHECK HARNESS AND CONNECTOR (BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY - PARKING ASSIST ECU AND BATTERY)
  1. Disconnect the G15 back sonar or clearance sonar switch assembly connector.

  1. Disconnect the F76 parking assist ECU connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    G15-6 (IG) - Body ground
    Engine switch on (IG)
    11 to 14 V
    Engine switch off
    Below 1 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G15-9 (ECU) - F76-25 (CSSW)
    Always
    Below 1 Ω
    G15-9 (ECU) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE PARKING ASSIST ECU (Click here)

4. CHECK HARNESS AND CONNECTOR (BACK SONAR OR CLEARANCE SONAR SWITCH ASSEMBLY - CLEARANCE WARNING ECU ASSEMBLY AND BATTERY)
  1. Disconnect the G15 back sonar or clearance sonar switch assembly connector.

  1. Disconnect the F12 clearance warning ECU assembly connector.

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    Tester Connection
    Switch Condition
    Specified Condition
    G15-6 (IG) - Body ground
    Engine switch on (IG)
    11 to 14 V
    Engine switch off
    Below 1 V

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    G15-9 (ECU) - F12-12 (CSSW)
    Always
    Below 1 Ω
    G15-9 (ECU) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR
OK

REPLACE CLEARANCE WARNING ECU ASSEMBLY (Click here)


← Clearance Sonar Main Switch Circuit (Sep 2011 – Dec 2011)Clearance Warning Buzzer Circuit (Sep 2011 – Dec 2011) →