2011-2013 Land Cruiser · Service Manual Power Source / Network

INSTALLATION

Removal / installation · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


1. INSTALL NETWORK GATEWAY ECU

E154162
  1. Install the ECU with the bolt.

  1. Connect the connector.


2. INSTALL DRIVER SIDE KNEE AIRBAG ASSEMBLY (w/ Driver Side Knee Airbag)

  1. B189604E01
    Connect the connector.

    NOTICE:
    When handling the airbag connector, take care not to damage the airbag wire harness.

  1. Install the driver side knee airbag with the 5 bolts.

    Torque:
    10 N*m{ 102 kgf*cm , 7 ft.*lbf }


3. INSTALL LOWER INSTRUMENT PANEL SUB-ASSEMBLY (w/o Driver Side Knee Airbag)

B180299
  1. Attach the 2 claws and connect the DLC3.

  1. Install the lower instrument panel with the 5 bolts.


4. INSTALL NO. 1 SWITCH HOLE BASE

B180298
  1. Connect the connectors.

  1. Attach the 4 claws to install the No. 1 switch hole base.


5. INSTALL LOWER NO. 1 INSTRUMENT PANEL FINISH PANEL
  1. Connect the connectors.

  1. B180296
    for Automatic Air Conditioning System:

    1. Attach the 2 claws to install the room temperature sensor.

  1. B181942
    Attach the 2 claws to connect the 2 control cables.

  1. w/ Driver Side Knee Airbag:

    1. Attach the 16 claws to install the lower No. 1 instrument panel finish panel.

    2. Install the 2 bolts.

      B291249

  1. w/o Driver Side Knee Airbag:

    1. Attach the 9 claws to install the lower No. 1 instrument panel finish panel.

    2. Install the 2 bolts.

      B291250

  1. B182569
    Attach the 2 claws to close the hole cover.


6. INSTALL NO. 1 INSTRUMENT PANEL UNDER COVER SUB-ASSEMBLY (w/ Floor Under Cover)

B182553
  1. Connect the connectors.

  1. Attach the 3 claws to install the No. 1 instrument panel under cover.

  1. Install the 2 screws.


7. INSTALL NO. 2 INSTRUMENT CLUSTER FINISH PANEL GARNISH

  1. Attach the 2 claws to install the No. 2 instrument cluster finish panel garnish.

    B291252E01

    Text in Illustration 
    *A
    w/ Entry and Start System
    *B
    w/o Entry and Start System


8. INSTALL NO. 1 INSTRUMENT CLUSTER FINISH PANEL GARNISH

E155133
  1. Attach the 3 claws to install the No. 1 instrument cluster finish panel garnish.


9. INSTALL LOWER INSTRUMENT PANEL PAD SUB-ASSEMBLY RH
  1. w/o Console Box Lid:

    1. Install the lower instrument panel pad sub-assembly RH (Click here).

  1. w/ Cool Box:

    1. Install the lower instrument panel pad sub-assembly RH (Click here).

  1. w/o Cool Box:

    1. Install the lower instrument panel pad sub-assembly RH (Click here).


10. INSTALL NO. 2 INSTRUMENT PANEL FINISH PANEL CUSHION
  1. w/o Console Box Lid:

    1. Install the No. 2 instrument panel finish panel cushion (Click here).

  1. w/ Cool Box:

    1. Install the No. 2 instrument panel finish panel cushion (Click here).

  1. w/o Cool Box:

    1. Install the No. 2 instrument panel finish panel cushion (Click here).


11. INSTALL FRONT DOOR SCUFF PLATE RH
  1. w/ Sliding Roof:
    Install the front door scuff plate (Click here ).

  1. w/o Sliding Roof:
    Install the front door scuff plate (Click here).


12. CONNECT CABLE TO NEGATIVE BATTERY TERMINAL (w/ Driver Side Knee Airbag)

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


13. CHECK SRS WARNING LIGHT (w/ Driver Side Knee Airbag)
  1. Check the SRS warning light (Click here).

← REMOVAL (from Jan 2012)INSTALLATION (from Jan 2012) →