Removal / installation · Vehicles built Sep 2011 – Dec 2011
Versions by build date: Sep 2011 – Dec 2011from Jan 2012
1.
INSTALL NO. 1 FUEL TANK HEAT INSULATOR
Install the heat insulator with the 4 clips.
Install the fuel tube clamp to the heat insulator.
2.
INSTALL FUEL TANK TO FILLER PIPE HOSE
Install the hose to the fuel tank as shown in the illustration.
Text in Illustration
*1
Fuel Tank Side Mark
*2
Hose Side Mark
HINT:
Align the fuel tank side mark with the hose side mark when installing the hose.
Tighten the hose clamp until the end of the hose clamp contacts the stopper as shown in the illustration.
Text in Illustration
*1
Stopper
3.
INSTALL FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY
Apply a light coat of gasoline or grease to a new gasket, and install it to the fuel tank.
Install the fuel suction with pump and gauge tube into the fuel tank.
Text in Illustration
*1
Protrusion
*2
Groove
Front
NOTICE:
Be careful not to bend the arm of the fuel sender gauge.
HINT:
Align the protrusion of the fuel suction with pump and gauge tube with the groove of the fuel tank.
Put the retainer on the fuel tank. While holding the fuel suction with pump and gauge tube, tighten the retainer 1 complete turn by hand.
Set SST on the retainer.
SST
09808-14030
HINT:
Hold the fuel suction tube assembly upright by hand to ensure that the fuel suction tube gasket is not moved out of position.
Securely attach the claws of SST to the protrusions of the retainer and fix SST in place.
Install SST while pressing the claws of SST against the retainer (toward the center of SST).
Using SST, tighten the retainer until the mark on the retainer is within range A on the fuel tank as shown in the illustration.
SST
09808-14030
HINT:
Fit the tips of SST onto the ribs of the retainer.
4.
INSTALL FUEL TANK MAIN TUBE, FUEL TANK RETURN TUBE AND NO. 2 FUEL TANK MAIN TUBE SUB-ASSEMBLY
Install the 3 fuel tank tubes with the 3 tube joint clips.
NOTICE:
Check that there are no scratches or foreign objects on the connecting parts.
Check that the fuel tube joints are inserted securely.
Check that the tube joint clips are on the collars of the fuel tube joints.
After installing the tube joint clips, check that the fuel tube joints cannot be pulled off.
Text in Illustration
*1
Fuel Tube Joint
*2
O-Ring
*3
Fuel Tube
*4
Tube Joint Clip
*a
CORRECT
*b
INCORRECT
Install the 3 fuel tank tubes to the fuel tank.
5.
INSTALL FUEL TANK SUB-ASSEMBLY
Set the fuel tank on a transmission jack and raise the fuel tank.
NOTICE:
Do not allow the fuel tank to contact the vehicle, especially the differential.
Raise the transmission jack.
Install the 2 fuel tank bands with the 2 pins and 2 clips.
Connect the 2 fuel tank bands with the 2 bolts.
Torque:
40 N*m{
408 kgf*cm
, 30 ft.*lbf
}
6.
CONNECT FUEL TANK TO FILLER PIPE HOSE
Connect the hose to the filler pipe as shown in the illustration.
Text in Illustration
*1
Hose Side Mark
*2
Pipe Side Mark
*a
0 to 0.3 mm
HINT:
Install the hose so that the distance between the fuel tank inlet pipe side mark and fuel tank to filler pipe hose side mark is 0 to 0.3 mm (0 to 0.0118 in.) as shown in the illustration.
Tighten the hose clamp until the end of the hose clamp contacts the stopper as shown in the illustration.
Text in Illustration
*1
Stopper
7.
CONNECT FUEL TANK BREATHER TUBE
Connect the fuel tank breather tube to the filler pipe and push the retainer.
Text in Illustration
*1
Retainer
HINT:
Push the parts together firmly until a "click" sound is heard.
NOTICE:
Before installing the tube connectors to the pipes, check if there is any damage or foreign matter in the connectors.
After the connection, check if the connectors and pipes are securely connected by trying to pull them apart.
Attach the fuel tube clamp.
8.
CONNECT NO. 2 FUEL MAIN TUBE SUB-ASSEMBLY
Connect the fuel main tube and push the retainer.
Text in Illustration
*1
Retainer
*2
Pipe
*3
Nylon Tube
*4
Connector
*5
O-Ring
HINT:
Push the parts together firmly until a "click" sound is heard.
NOTICE:
Before installing the tube connectors to the pipes, check if there is any damage or foreign matter in the connectors.
After the connection, check if the connectors and pipes are securely connected by trying to pull them apart.
Attach the fuel tube clamp.
9.
CONNECT NO. 2 FUEL TANK BREATHER TUBE
Connect the fuel tank breather tube and push the retainer.
Text in Illustration
*1
Retainer
*2
Pipe
*3
Nylon Tube
*4
Connector
*5
O-Ring
HINT:
Push the parts together firmly until a "click" sound is heard.
NOTICE:
Before installing the tube connectors to the pipes, check if there is any damage or foreign matter in the connectors.
After the connection, check if the connectors and pipes are securely connected by trying to pull them apart.
Attach the fuel tube clamp.
10.
CONNECT FUEL TANK RETURN TUBE
Connect the fuel tank return tube and push the retainer.
Text in Illustration
*1
Retainer
*2
Pipe
*3
Nylon Tube
*4
Connector
*5
O-Ring
HINT:
Push the parts together firmly until a "click" sound is heard.
NOTICE:
Before installing the tube connectors to the pipes, check if there is any damage or foreign matter in the connectors.
After the connection, check if the connectors and pipes are securely connected by trying to pull them apart.
Attach the fuel tube clamp.
11.
CONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY
Connect the fuel tank main tube and push the retainer.
Text in Illustration
*1
Retainer
*2
Pipe
*3
Nylon Tube
*4
Connector
*5
O-Ring
HINT:
Push the parts together firmly until a "click" sound is heard.
NOTICE:
Before installing the tube connectors to the pipes, check if there is any damage or foreign matter in the connectors.
After the connection, check if the connectors and pipes are securely connected by trying to pull them apart.
Attach the fuel tube clamp.
12.
INSTALL NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY
Install the tank protector with the 5 bolts.
Torque:
20 N*m{
204 kgf*cm
, 15 ft.*lbf
}
13.
INSTALL FUEL TANK CAP ASSEMBLY
14.
INSTALL REAR FLOOR NO. 2 SERVICE HOLE COVER
Connect the fuel pump and fuel sender gauge connector.
Install the service hole cover with new butyl tape.
Install the air duct and 2 screws.
15.
INSTALL FRONT FLOOR CARPET ASSEMBLY
16.
INSTALL REAR NO. 2 SEAT ASSEMBLY
for Face to Face Seat Type: Install the rear No. 2 seat assembly (Click here).
except Face to Face Seat Type: Install the rear No. 2 seat assembly (Click here).