2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

REMOVAL

Removal / installation · Vehicles built from Jan 2012

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012


1. DISCHARGE FUEL SYSTEM PRESSURE
(Click here)

2. PRECAUTION

NOTICE:
After turning the engine switch off, waiting time may be required before disconnecting the cable from the battery terminal. Therefore, make sure to read the disconnecting the cable from the battery terminal notice before proceeding with work (Click here).


3. DISCONNECT CABLE FROM NEGATIVE BATTERY TERMINAL

NOTICE:
When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).


4. REMOVE REAR NO. 1 SEAT ASSEMBLY RH (for 60/40 Split Seat Type 40 Side)
(Click here)

5. REMOVE REAR NO. 1 SEAT ASSEMBLY LH (for 60/40 Split Seat Type 60 Side)
(Click here)

6. REMOVE REAR NO. 2 SEAT ASSEMBLY
  1. for Face to Face Seat Type:
    Remove the rear No. 2 seat assembly (Click here).

  1. except Face to Face Seat Type:
    Remove the rear No. 2 seat assembly (Click here).


7. REMOVE FRONT FLOOR CARPET ASSEMBLY
  1. Turn over the floor carpet.

    HINT:
    Fold back the floor carpet so that the air duct can be removed.


8. REMOVE REAR FLOOR NO. 2 SERVICE HOLE COVER

  1. A181426
    Remove the 2 screws and air duct.

  1. A181427
    Remove the service hole cover.


9. REMOVE FUEL TANK CAP ASSEMBLY

10. REMOVE NO. 1 FUEL TANK PROTECTOR SUB-ASSEMBLY

  1. A175014
    Remove the 5 bolts and fuel tank protector.


11. DISCONNECT FUEL TANK MAIN TUBE SUB-ASSEMBLY

  1. A176336E02
    Detach the fuel tube clamp.

  1. Pull up the retainer and disconnect the fuel tank main tube.

    Text in Illustration 
    *1
    Retainer
    *2
    Pipe
    *3
    Nylon Tube
    *4
    Connector
    *5
    O-Ring

    NOTICE:
    1. Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.
    2. Do not use any tools to separate the pipe and connector.
    3. Do not forcefully bend or twist the nylon tube.
    4. Check for foreign matter on the pipe seal surface. Clean if necessary.
    5. Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.
    6. If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.


12. DRAIN FUEL
  1. Connect the cable to the negative (-) battery terminal.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. Connect the intelligent tester to the DLC3.

  1. Turn the engine switch on (IG).

    NOTICE:
    Do not start the engine.

  1. Turn the intelligent tester on.

  1. Enter the following menus: Powertrain / Engine and ECT / Active Test / Control the Fuel Pump / Speed.

    CAUTION:
    1. Do not smoke or be near an open flame when working on the fuel system.
    2. Secure good ventilation.
    3. Keep gasoline away from rubber or leather parts.


    HINT:
    A237023
    If the fuel pump does not operate, remove the fuel tube joint clip and disconnect the fuel tank return tube, and drain fuel from the port shown in the illustration.

  1. Disconnect the cable from the negative (-) battery terminal.

    NOTICE:
    When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).

  1. A237024
    Disconnect the fuel pump and fuel sender gauge connector.


13. DISCONNECT FUEL TANK RETURN TUBE

  1. A176338E02
    Detach the fuel tube clamp.

  1. Pull up the retainer and disconnect the fuel tank return tube.

    Text in Illustration 
    *1
    Retainer
    *2
    Pipe
    *3
    Nylon Tube
    *4
    Connector
    *5
    O-Ring

    NOTICE:
    1. Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.
    2. Do not use any tools to separate the pipe and connector.
    3. Do not forcefully bend or twist the nylon tube.
    4. Check for foreign matter on the pipe seal surface. Clean if necessary.
    5. Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.
    6. If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.


14. DISCONNECT NO. 2 FUEL MAIN TUBE SUB-ASSEMBLY

  1. A175061E02
    Detach the fuel tube clamp.

  1. Pull up the retainer and disconnect the fuel tank main tube.

    Text in Illustration 
    *1
    Retainer
    *2
    Pipe
    *3
    Nylon Tube
    *4
    Connector
    *5
    O-Ring

    NOTICE:
    1. Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.
    2. Do not use any tools to separate the pipe and connector.
    3. Do not forcefully bend or twist the nylon tube.
    4. Check for foreign matter on the pipe seal surface. Clean if necessary.
    5. Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.
    6. If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.


15. DISCONNECT NO. 2 FUEL TANK BREATHER TUBE

  1. A175063E02
    Detach the fuel tube clamp.

  1. Pull up the retainer and disconnect the fuel tank breather tube.

    Text in Illustration 
    *1
    Retainer
    *2
    Pipe
    *3
    Nylon Tube
    *4
    Connector
    *5
    O-Ring

    NOTICE:
    1. Check for foreign matter in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.
    2. Do not use any tools to separate the pipe and connector.
    3. Do not forcefully bend or twist the nylon tube.
    4. Check for foreign matter on the pipe seal surface. Clean if necessary.
    5. Put the pipe and connector ends in plastic bags to prevent damage and foreign matter contamination.
    6. If the pipe and connector are stuck together, pinch the connector between your fingers and turn it carefully to disconnect it.


16. DISCONNECT FUEL TANK BREATHER TUBE

  1. A181491E02
    Detach the fuel tube clamp.

  1. Pull up the retainer and disconnect the fuel tank breather tube from the filler pipe.

    Text in Illustration 
    *1
    Retainer

    NOTICE:
    1. Do not use any tools in this procedure.
    2. Check for any dirt and foreign matter contamination in the pipe and around the connector. Clean if necessary. Foreign matter may damage the O-ring or cause leaks in the seal between the pipe and connector.


17. DISCONNECT FUEL TANK TO FILLER PIPE HOSE

  1. A175067
    Disconnect the hose from the filler pipe.


18. REMOVE FUEL TANK SUB-ASSEMBLY
  1. Place a transmission jack under the fuel tank.

  1. A175024
    Remove the 2 bolts, 2 clips, 2 pins and 2 fuel tank bands.


19. REMOVE FUEL TANK MAIN TUBE, FUEL TANK RETURN TUBE AND NO. 2 FUEL TANK MAIN TUBE SUB-ASSEMBLY

  1. A176319E03
    Remove the 3 fuel tube joint clips and pull out the 3 fuel tubes.
    Text in Illustration 
    *1
    Tube Joint
    *2
    Tube Joint Clip
    *3
    Fuel Tank Tube
    *4
    O-Ring
    *5
    Fuel Suction Plate

    NOTICE:
    1. Remove any dirt and foreign matter on the fuel tube joint before performing this work.
    2. Do not allow any scratches or foreign matter on the parts when disconnecting them, as the fuel tube joint contains the O-rings that seal the plug.
    3. Perform this work by hand. Do not use any tools.
    4. Do not forcibly bend, twist or turn the nylon tube.
    5. Protect the disconnected part by covering it with a plastic bag and tape after disconnecting the fuel tubes.

  1. A175070
    Remove the 3 fuel tubes from the fuel tank.


20. REMOVE FUEL SUCTION WITH PUMP AND GAUGE TUBE ASSEMBLY

  1. A242908E01
    Set SST on the retainer.
    SST
    09808-14030  

    HINT:
    1. Securely attach the claws of SST to the protrusion of the retainer and fix SST in place.
    2. Install SST while pressing the claws of SST against the retainer (towards the center of SST).

  1. A242907
    Using SST, loosen the retainer.
    SST
    09808-14030  

    NOTICE:
    1. Do not use any tools other than those specified in this operation. Damage to the retainer or the fuel tank may result.
    2. While pressing down on SST so that the claws of SST do not slip off the protrusion of the retainer, turn the retainer counterclockwise to loosen it.

    HINT:
    The protrusion of the retainer fit in the ends of SST.

  1. Remove the retainer while holding the fuel suction tube assembly by hand.

  1. Remove the gasket from the fuel tank.


21. REMOVE FUEL TANK TO FILLER PIPE HOSE

  1. A176316
    Remove the hose from the fuel tank.


22. REMOVE NO. 1 FUEL TANK HEAT INSULATOR

  1. A175033E01
    Remove the fuel tube clamp from the heat insulator.

  1. Using needle-nose pliers, remove the 4 clips shown in the illustration and then remove the heat insulator.

← REMOVAL (Sep 2011 – Dec 2011)INSTALLATION (Sep 2011 – Dec 2011) →