2011-2013 Land Cruiser · Service Manual Suspension

INSTALLATION

Removal / installation · Vehicles built from Sep 2011


1. INSTALL HEIGHT CONTROL PUMP AND MOTOR ASSEMBLY

  1. C172732
    Install the pump and motor with the 3 bolts.

    Torque:
    31 N*m{ 316 kgf*cm , 23 ft.*lbf }

  1. C172672
    Connect the 2 connectors and 3 clamps.


2. INSTALL HEIGHT CONTROL TUBE CLAMP

  1. C176840E01
    Install the tube clamp with the 2 bolts.

    Torque:
    20 N*m{ 204 kgf*cm , 15 ft.*lbf }

  1. Connect the reservoir hose to the tube clamp.


3. CONNECT REAR NO. 6 HEIGHT CONTROL TUBE

  1. C176223E01
    Using a union nut wrench, connect the control tube to the pump and motor.

    Torque:
    without union nut wrench:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }
    with union nut wrench:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }

    HINT:
    1. Use a torque wrench with a fulcrum length of 300 mm (11.8 in.).
    2. The torque value for use with a union nut wrench is effective when the union nut wrench is parallel to the torque wrench.


4. BLEED AIR FROM SUSPENSION FLUID

  1. C176402
    With the engine stopped, fill the reservoir tank with fluid.

    NOTICE:
    When the engine starts, the pump operates and fluid is supplied to each cylinder from the reservoir tank. Therefore, add the necessary amount of fluid so that the reservoir tank does not become empty.

    HINT:
    At this point, the vehicle height is low because the pressure of the cylinders is low.

  1. With the vehicle on a level surface, start the engine and set the vehicle height to NORMAL with the suspension control switch.

  1. When the vehicle height becomes NORMAL and the pump stops, stop the engine.

  1. C172939
    Connect a hose to the bleeder plug of the front left side or right side control valve, then loosen the bleeder plug.

    CAUTION:
    Be careful when loosening the control valve bleeder plug because the front vehicle height drops rapidly.

  1. After the fluid containing air stops coming out, retighten the bleeder plug.

    Torque:
    8.3 N*m{ 85 kgf*cm , 73 in.*lbf }

    HINT:
    If the procedures are performed for the first time on the left side, perform the procedures on the right side for the second time.

  1. C172940
    Connect a hose to the bleeder plug of the rear left side or right side control valve, then loosen the bleeder plug.

    CAUTION:
    Be careful when loosening the control valve bleeder plug because the rear vehicle height drops rapidly.

  1. After the fluid containing air stops coming out, retighten the bleeder plug.

    Torque:
    8.3 N*m{ 85 kgf*cm , 73 in.*lbf }

    HINT:
    If the procedures are performed for the first time on the left side, perform the procedures on the right side for the second time.

  1. Repeat the previous 4 procedures until the fluid containing air stop coming out.


5. CHECK FLUID LEVEL IN RESERVOIR

  1. C176461
    With the vehicle empty, after setting the vehicle height to NORMAL from LO, check the indicator to make sure the vehicle height is NORMAL and check that the fluid level in the reservoir tank is within the specified range (MAX, MIN).

    HINT:
    After changing the vehicle height from LO to NORMAL, do not stop the engine for 25 seconds because the pressure control for the main accumulator is operating. After that, check the fluid level.


6. INSPECT FOR SUSPENSION FLUID LEAK
  1. Check that the union nuts shown in the illustration are tightened to the specified torque.

    Torque:
    without union nut wrench:
    15 N*m{ 155 kgf*cm , 11 ft.*lbf }
    with union nut wrench:
    14 N*m{ 143 kgf*cm , 10 ft.*lbf }

    HINT:
    1. Use a torque wrench with a fulcrum length of 300 mm (11.8 in.).
    2. The torque value for use with a union nut wrench is effective when the union nut wrench is parallel to the torque wrench.

  1. Check for fluid leakage from the parts and connections.

    C176381E01

    HINT:
    For union nuts and union bolts not shown in the illustration, refer to the installation procedures for each title.


7. INSTALL FUEL TANK FILLER PIPE PROTECTOR

  1. C172735
    Using a T30 "TORX" socket wrench, install the pipe protector with the 3 screws and grommet.

  1. Install the new grommet.


8. INSTALL NO. 1 LUGGAGE COMPARTMENT SIDE COVER PROTECTOR

C179456
  1. Install the protector with 2 new grommets.

  1. Install the 2 screws.


9. INSTALL REAR BUMPER COVER
  1. for Standard:
    Install the bumper cover (Click here).

  1. w/ Towing Hitch:
    Install the bumper cover (Click here).

  1. w/ Pintle Hook:
    Install the bumper cover (Click here).


10. INSTALL REAR QUARTER PANEL MUDGUARD RH

B180883
  1. Install the mudguard with the clip.

  1. Using a T30 "TORX" socket, install the 7 screws.

← REASSEMBLY (from Sep 2011)COMPONENTS (from Sep 2011) →