INSTALLATION
Removal / installation · Vehicles built Sep 2011 – Dec 2011
Versions by build date: Sep 2011 – Dec 2011 from Jan 2012
| 1.
INSTALL FUEL SENDER GAUGE ASSEMBLY |
 |
- Install a new gasket to the sender gauge.
Install the sender gauge with the 5 screws.
-
Torque:
- 1.5 N*m{
15 kgf*cm
, 13 in.*lbf
}
- NOTICE:
- Be careful not to bend the arm of the fuel sender gauge.
Connect the sender gauge connector.
| 2.
INSTALL REAR FLOOR SERVICE HOLE COVER |
 |
- Install the service hole cover with new butyl tape.
| 3.
INSTALL REAR NO. 7 AIR DUCT (w/ Rear Air Conditioning System) |
 |
- Attach the 4 clips to install the air duct.
- HINT:
- Attach the clips in the order shown in the illustration.
| 4.
INSTALL REAR FLOOR MAT ASSEMBLY |
 |
- Attach the 5 clips to install the floor mat.
| 5.
INSTALL REAR AIR DUCT GUIDE (w/ Rear Air Conditioning System)
|
 |
- Attach the claw to install the guide.
Install the screw.
- HINT:
- Use the same procedures for both sides.
| 6.
INSTALL AIR DUCT PLUG (w/ Rear Air Conditioning System)
|
 |
- Attach the 2 claws to install the plug.
- HINT:
- Use the same procedures for both sides.
| 7.
INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY LH |
 |
w/ Sliding Roof:
Install the front quarter trim panel assembly LH (Click here).
w/o Sliding Roof:
Install the front quarter trim panel assembly LH (Click here).
| 8.
INSTALL FRONT QUARTER TRIM PANEL ASSEMBLY RH |
 |
w/ Sliding Roof:
Install the front quarter trim panel assembly RH (Click here).
w/o Sliding Roof:
Install the front quarter trim panel assembly RH (Click here).
| 9.
INSTALL REAR SEAT COVER CAP (w/ Reat No. 2 Seat, except Face to Face Seat Type)
|
 |
- HINT:
- Use the same procedure to install the rear seat cover cap on the other side.
Attach the 3 claws to install the rear seat cover cap.
| 10.
INSTALL REAR FLOOR MAT REAR SUPPORT PLATE
|
 |
Attach the 6 clips to install the support plate.
| 11.
INSTALL REAR DOOR SCUFF PLATE LH
|
 |
Attach the 7 claws and 4 clips to install the scuff plate.
| 12.
INSTALL REAR DOOR SCUFF PLATE RH
|
 |
- HINT:
- Use the same procedures described for the LH side.
| 13.
INSTALL REAR STEP COVER
|
 |
- HINT:
- Use the same procedure to install the step cover on the other side.
Attach the 2 claws to install the step cover.
| 14.
INSTALL REAR NO. 2 SEAT ASSEMBLY |
 |
for Face to Face Seat Type:
Install the rear No. 2 seat assembly (Click here).
except Face to Face Seat Type:
Install the rear No. 2 seat assembly (Click here).
| 15.
INSTALL REAR NO. 1 SEAT ASSEMBLY RH (for 60/40 Split Seat Type 40 Side) |
 |
Install the rear No. 1 seat assembly RH (Click here).
| 16.
INSTALL REAR NO. 1 SEAT ASSEMBLY LH (for 60/40 Split Seat Type 60 Side) |
 |
Install the rear No. 1 seat assembly LH (Click here).
| 17.
INSTALL CABLE TO NEGATIVE BATTERY TERMINAL |
 |
- NOTICE:
- When disconnecting the cable, some systems need to be initialized after the cable is reconnected (Click here).
| 18.
CHECK SRS WARNING LIGHT |
 |
Check the SRS warning light (Click here).