2011-2013 Land Cruiser · Service Manual Engine / Hybrid / EV System

Clutch Switch Circuit

Circuit diagnosis · Vehicles built Sep 2011 – Dec 2011

Versions by build date: Sep 2011 – Dec 2011 from Jan 2012

DESCRIPTION

When the clutch pedal is released, the ECM receives positive (+) battery voltage through the LH-IG fuse. While depressing the clutch pedal, the clutch switch sends a signal to terminal D*1 or CLSW*2 of the ECM. The ECM cancels cruise control when terminal D*1 or CLSW*2 receives the signal.

HINT:
  1. *1: for 1GR-FE
  2. *2: for 1VD-FTV


WIRING DIAGRAM

E149076E01
E149076E02

INSPECTION PROCEDURE


1. INSPECT FUSE (LH-IG)
  1. Remove the LH-IG fuse from the main body ECU.

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Condition
    Specified Condition
    LH-IG fuse
    Always
    Below 1 Ω



NG
REPLACE FUSE
OK


2. INSPECT ECM

  1. E149077E01
    Disconnect the C45*1, C46*2, A38*3 or A52*4 ECM connector.

    HINT:
    1. *1: for 1GR-FE LHD
    2. *2: for 1GR-FE RHD
    3. *3: for 1VD-FTV LHD
    4. *4: for 1VD-FTV RHD

  1. Measure the voltage according to the value(s) in the table below.

    Standard Voltage:
    for 1GR-FE LHD 
    Tester Connection
    Switch Condition
    Specified Condition
    C45-26 (D) - Body ground
    Ignition switch ON
    Clutch pedal depressed
    Below 1 V
    Ignition switch ON
    Clutch pedal released
    11 to 14 V
    for 1GR-FE RHD 
    Tester Connection
    Switch Condition
    Specified Condition
    C46-26 (D) - Body ground
    Ignition switch ON
    Clutch pedal depressed
    Below 1 V
    Ignition switch ON
    Clutch pedal released
    11 to 14 V
    for 1VD-FTV LHD 
    Tester Connection
    Switch Condition
    Specified Condition
    A38-42 (CLSW) - Body ground
    Ignition switch ON
    Clutch pedal depressed
    Below 1 V
    Ignition switch ON
    Clutch pedal released
    11 to 14 V
    for 1VD-FTV RHD 
    Tester Connection
    Switch Condition
    Specified Condition
    A52-42 (CLSW) - Body ground
    Ignition switch ON
    Clutch pedal depressed
    Below 1 V
    Ignition switch ON
    Clutch pedal released
    11 to 14 V



NG
Go to step 3
OK

PROCEED TO NEXT CIRCUIT INSPECTION SHOWN IN PROBLEM SYMPTOMS TABLE (Click here)

3. INSPECT CLUTCH SWITCH ASSEMBLY
  1. Turn the Ignition switch off.

  1. E149078E01
    Disconnect the A50*1 or e2*2 clutch switch connector.

    HINT:
    1. *1: for LHD
    2. *2: for RHD

  1. Remove the clutch switch (Click here for LHD, Click here for RHD).

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    Tester Connection
    Switch Condition
    Specified Condition
    1 - 2
    Pushed (On)
    Below 1 Ω
    Not pushed (Off)
    10 kΩ or higher

    Result 
    Result
    Proceed to
    OK
    A
    NG (for LHD)
    B
    NG (for RHD)
    C

  1. Install the clutch switch (Click here for LHD, Click here for RHD).



B
REPLACE CLUTCH SWITCH ASSEMBLY (Click here)

C
REPLACE CLUTCH SWITCH ASSEMBLY (Click here)
A


4. CHECK HARNESS AND CONNECTOR (ECM - CLUTCH SWITCH)

  1. E149079E01
    Disconnect the C45*1, C46*2, A38*3 or A52*4 ECM connector.

    HINT:
    1. *1: for 1GR-FE LHD
    2. *2: for 1GR-FE RHD
    3. *3: for 1VD-FTV LHD
    4. *4: for 1VD-FTV RHD

  1. Disconnect the A50*1 or e2*2 clutch switch connector.

    HINT:
    1. *1: for LHD
    2. *2: for RHD

  1. Measure the resistance according to the value(s) in the table below.

    Standard Resistance:
    for 1GR-FE LHD 
    Tester Connection
    Condition
    Specified Condition
    C45-26 (D) - A50-2
    Always
    Below 1 Ω
    C45-26 (D) - Body ground
    Always
    10 kΩ or higher
    for 1GR-FE RHD 
    Tester Connection
    Condition
    Specified Condition
    C46-26 (D) - e2-2
    Always
    Below 1 Ω
    C46-26 (D) - Body ground
    Always
    10 kΩ or higher
    for 1VD-FTV LHD 
    Tester Connection
    Condition
    Specified Condition
    A38-42 (CLSW) - A50-2
    Always
    Below 1 Ω
    A38-42 (CLSW) - Body ground
    Always
    10 kΩ or higher
    for 1VD-FTV RHD 
    Tester Connection
    Condition
    Specified Condition
    A52-42 (CLSW) - e2-2
    Always
    Below 1 Ω
    A52-42 (CLSW) - Body ground
    Always
    10 kΩ or higher



NG
REPAIR OR REPLACE HARNESS OR CONNECTOR (ECM - CLUTCH SWITCH)
OK

REPAIR OR REPLACE HARNESS OR CONNECTOR (BATTERY - CLUTCH SWITCH)


← P0575 Cruise Control Input Circuit (+ P0607) (from Jan 2012)Clutch Switch Circuit (from Jan 2012) →